Re: What does 'show ip eigrp topology x.x.x.x/x' actually show?

here is my output:

R1#sh ip eigrp topology 22.22.22.22/32
IP-EIGRP (AS 1): Topology entry for 22.22.22.22/32
  State is Passive, Query origin flag is 1, 1 Successor(s), FD is 2297856
  Routing Descriptor Blocks:
  192.168.12.2 (Serial0/0), from 192.168.12.2, Send flag is 0x0
      Composite metric is (2297856/128256), Route is Internal
      Vector metric:
        Minimum bandwidth is 1544 Kbit
        Total delay is 25000 microseconds
        Reliability is 255/255
        Load is 1/255
        Minimum MTU is 1500
        Hop count is 1
  192.168.13.3 (Serial0/1), from 192.168.13.3, Send flag is 0x0
      Composite metric is (2809856/2297856), Route is Internal
      Vector metric:
        Minimum bandwidth is 1544 Kbit
        Total delay is 45000 microseconds
        Reliability is 255/255
        Load is 1/255
        Minimum MTU is 1500
        Hop count is 2
R1#

Same behavior.

On 10 August 2012 01:05, dia.aliou_at_gmail.com <dia.aliou_at_gmail.com> wrote:

> Sorry I didnt check well, had some variance and delay configs.
>
>
> On 10 August 2012 00:39, Keller Giacomarro <keller.g_at_gmail.com> wrote:
>
>> Good thought on variance, but I do not have it configured.
>>
>> R3(config-router)#do show ver | inc 12.4
>> Cisco IOS Software, C2600 Software (C2600-ADVENTERPRISEK9-M), Version
>> 12.4(15)T14, RELEASE SOFTWARE (fc2)
>> R3(config-router)#do show run | inc variance
>> R3(config-router)#
>>
>> I'm also pretty sure it's not an artifact from my setup, as the output
>> I pasted was directly out of the solution guide!
>>
>> Keller Giacomarro
>> keller.g_at_gmail.com
>>
>>
>> On Fri, Aug 10, 2012 at 2:35 AM, dia.aliou_at_gmail.com
>> <dia.aliou_at_gmail.com> wrote:
>> > Hi Keller,
>> > Which IOS version are you using?
>> > Just tested in 12.4T, I only see feasible successor when I use the below
>> > command.
>> > I would guess you have variance configured under eigrp.
>> >
>> > /Aliou
>> >
>> > On 10 August 2012 00:07, Keller Giacomarro <keller.g_at_gmail.com> wrote:
>> >>
>> >> Okay, pretty stumped here.
>> >>
>> >> R3#show ip eigrp topology 150.1.7.0 255.255.255.0
>> >> IP-EIGRP (AS 100): Topology entry for 150.1.7.0/24
>> >> State is Passive, Query origin flag is 1, 1 Successor(s), FD is 128256
>> >> Routing Descriptor Blocks:
>> >> 155.1.37.7 (FastEthernet0/0), from 155.1.37.7, Send flag is 0x0
>> >> Composite metric is (128256/128000), Route is Internal
>> >> Vector metric:
>> >> Minimum bandwidth is 100000 Kbit
>> >> Total delay is 5010 microseconds
>> >> Reliability is 255/255
>> >> Load is 1/255
>> >> Minimum MTU is 1500
>> >> Hop count is 1
>> >> 155.1.0.5 (Serial1/0.1), from 155.1.0.5, Send flag is 0x0
>> >> Composite metric is (1152512/640512), Route is Internal
>> >> Vector metric:
>> >> Minimum bandwidth is 128 Kbit
>> >> Total delay is 45020 microseconds
>> >> Reliability is 255/255
>> >> Load is 1/255
>> >>
>> >> I thought that 'show ip eigrp topo x.x.x.x/x' showed successors and
>> >> feasible successors only. But the second entry above shows an AD of
>> >> 640512, which is larger than the FD of 128256. Is this considered a
>> >> Feasible Successor or not? If not, what's it doing in this command
>> >> output?
>> >>
>> >> Thanks as always!
>> >>
>> >> Keller Giacomarro
>> >> keller.g_at_gmail.com
>> >>
>> >>
>> >> Blogs and organic groups at http://www.ccie.net
>> >>
>> >> _______________________________________________________________________
>> >> Subscription information may be found at:
>> >> http://www.groupstudy.com/list/CCIELab.html

Blogs and organic groups at http://www.ccie.net
Received on Fri Aug 10 2012 - 01:07:54 ART