Re: OT:cisco 6500 runing configration..help??

my end config

rommon 1 > set
PS1=rommon ! >
?=0
BSI=0
ACL_DENY=0
PF_REDUN_CRASH_COUNT=0
LOG_PREFIX_VERSION=1
BOOT=bootflash:s72033-pk9sv-
mz.122-18.SXD4.bin,1
CONFIG_FILE=bootflash:startup-config
BOOTLDR=bootflash:c6msfc3-psv-mz.122-17d.SXB5.bin
SLOTCACHE=cards;
RET_2_RTS=18:35:28 PKT Wed Jun 8 2011
RET_2_RCALTS=1307540127.

when i unpluged the power cord everything remove under the >set command

Thanks

On Wed, Jan 25, 2012 at 6:16 PM, George J. Sanchez <marco207p_at_gmail.com>wrote:

> Sup-bootflash:
>
> In rommon check your boot via
> Rommon> set
>
>
> If the return value is what you want, run the command boot "then the value
> shown in the set settings" f the value in the set return values is wrong
> use the command set boot: xxxxxx
>
> Where xxxx is the location of your .bin image.
>
> I've had these problems with stubborn 6506's in the past when someone at a
> customer site tries to do craziness and jacks the boot order.
>
> Regards,
> Joe Sanchez
>
> On Jan 25, 2012, at 6:02 AM, muhammad adnan <taurusadnan19_at_gmail.com>
> wrote:
>
> > i fix everything but when i unplugged the 6509 power cord then switch
> lost
> > his startup config and boot config on SP(switch processor)
> > and switch goes into rommon monitor mode then i put to manually the boot
> > command at rommon and manually copy the
> > startup-config into the runing-config and also restore the vlan.dat file
> > manually.
> >
> >
> > kindly help me in this regard
> >
> > Thanks
> > Muhammad Adnan
> >
> >
> > On Tue, Jan 24, 2012 at 11:52 PM, kennypual <pdaramol_at_gmail.com> wrote:
> >
> >> Also check your remote switch config register setting
> >>
> >>
> >>
> >> On Tue, Jan 24, 2012 at 11:08 AM, muhammad adnan <
> taurusadnan19_at_gmail.com>wrote:
> >>
> >>> my config reg was configured as 0x2102 but i change it to the 0x2101.
> >>> After
> >>> that when i put #config t command on switch it give me error message.
> >>>
> >>> Router#conf t
> >>>
> >>> % Warning: Waiting for draco inventory message from SP.
> >>>
> >>> % Reload MSFC without saving configuration if the MSFC does not r
> >>>
> >>> ecover.
> >>> % Configuration allowed only from Primary
> >>>
> >>> any one kindly help on this error
> >>> Thanks
> >>>
> >>>
> >>> On Tue, Jan 24, 2012 at 8:48 PM, Michael Seonarain <
> mseonarain_at_gmail.com
> >>>> wrote:
> >>>
> >>>> It is stored in nvram and check the config-register setting..
> >>>>
> >>>> On Tue, Jan 24, 2012 at 5:59 AM, muhammad adnan <
> >>> taurusadnan19_at_gmail.com>wrote:
> >>>>
> >>>>> Hello to all group members:-
> >>>>> i want to know where the startup
> >>>>> configration of cisco 6500 switch save.i am facing a problem when i
> >>> unplug
> >>>>> the power of the switch i lost my startup configration and switch
> boots
> >>>>> with default configuration.kindly help me on this matter.
> >>>>>
> >>>>>
> >>>>>
> >>>>>
> >>>>>
> >>>>> Thanks a lot
> >>>>> Muhammad Adnan
> >>>>>
> >>>>>
> >>>>> Blogs and organic groups at http://www.ccie.net
> >>>>>
> >>>>>
> _______________________________________________________________________
> >>>>> Subscription information may be found at:
> >>>>> http://www.groupstudy.com/list/CCIELab.html
> >>>
> >>>
> >>> Blogs and organic groups at http://www.ccie.net
> >>>
> >>> _______________________________________________________________________
> >>> Subscription information may be found at:
> >>> http://www.groupstudy.com/list/CCIELab.html
> >
> >
> > Blogs and organic groups at http://www.ccie.net
> >
> > _______________________________________________________________________
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html

Blogs and organic groups at http://www.ccie.net
Received on Wed Jan 25 2012 - 18:31:50 ART