Re: L3 etherchannel Dynamips

hey edmore,
use no switchport command on the individual interfaces first before bundling
them up
it should work, i think

but i dont think you're having dynamips problem

On Fri, Feb 19, 2010 at 12:37 PM, Tolulope Ogunsina <togunsina_at_gmail.com>wrote:

> Hi,
> Dynamips does NOT emulate switches or ISRs.
> The NM16ESW module is still NOT a switch :-)
>
> Configuration features of the Etherswitch module are documented here:
>
>
> http://www.cisco.com/en/US/docs/ios/lanswitch/configuration/guide/lsw_enet_switch_net_ps6350_TSD_Products_Configuration_Guide_Chapter.html
>
>
> The NM16ESW does not support layer 3 etherchannels.
>
> On 2/19/10, Edmore Chingwena <chingwenaed_at_gmail.com> wrote:
> > Hi Guys
> >
> > Any help on the issue below I am experiencing any ideas
> >
> > Rack1SW2(config)#int po2
> > Rack1SW2(config-if)#ip address 155.1.108.8 255.255.255.0
> >
> > % IP addresses may not be configured on L2 links.
> >
> > Rack1SW2(config-if)#no switchport
> > Command rejected: not allowed under port channel.
> > Rack1SW2(config-if)#
> >
> > Rack1SW2(config-if)#do show run int port 2
> > Building configuration...
> >
> > Current configuration : 31 bytes
> > !
> > interface Port-channel2
> > end
> >
> > Rack1SW2(config-if)#do show run int fa 1/13
> > Building configuration...
> >
> > Current configuration : 59 bytes
> > !
> > interface FastEthernet1/13
> > channel-group 2 mode on
> > end
> >
> > Rack1SW2(config-if)#do show run int fa 1/14
> > Building configuration...
> >
> > Current configuration : 59 bytes
> > !
> > interface FastEthernet1/14
> > channel-group 2 mode on
> > end
> >
> > Rack1SW2(config-if)#do show run int fa 1/15
> > Building configuration...
> >
> > Current configuration : 59 bytes
> > !
> > interface FastEthernet1/15
> > channel-group 2 mode on
> > end
> >
> > Rack1SW2(config-if)#do show int port 2
> > Port-channel2 is up, line protocol is up
> > Hardware is EtherChannel, address is c20a.0da8.f10f (bia
> c20a.0da8.f10f)
> > MTU 1500 bytes, BW 300000 Kbit/sec, DLY 1000 usec,
> > reliability 255/255, txload 1/255, rxload 1/255
> > Encapsulation ARPA, loopback not set
> > Keepalive set (10 sec)
> > Auto-duplex, Auto-speed
> > Members in this channel: Fa1/13 Fa1/14 Fa1/15
> > ARP type: ARPA, ARP Timeout 04:00:00
> > Last input 00:00:01, output never, output hang never
> > Last clearing of "show interface" counters never
> > Input queue: 39/75/370/0 (size/max/drops/flushes); Total output drops:
> 0
> > Queueing strategy: fifo
> > Output queue: 0/40 (size/max)
> > 5 minute input rate 0 bits/sec, 0 packets/sec
> > 5 minute output rate 0 bits/sec, 0 packets/sec
> > 0 packets input, 0 bytes, 0 no buffer
> > Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
> > 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
> > 0 input packets with dribble condition detected
> > 0 packets output, 0 bytes, 0 underruns
> > 0 output errors, 0 collisions, 1 interface resets
> > 0 unknown protocol drops
> > 0 babbles, 0 late collision, 0 deferred
> > 0 lost carrier, 0 no carrier
> > 0 output buffer failures, 0 output buffers swapped out
> > Rack1SW2(config-if)#do show version
> > Cisco IOS Software, 3700 Software (C3725-ADVENTERPRISEK9-M), Version
> > 12.4(15)T10, RELEASE SOFTWARE (fc3)
> > Technical Support: http://www.cisco.com/techsupport
> > Copyright (c) 1986-2009 by Cisco Systems, Inc.
> > Compiled Mon 14-Sep-09 15:53 by prod_rel_team
> >
> >
> > Blogs and organic groups at http://www.ccie.net
> >
> > _______________________________________________________________________
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html
> >
> >
> >
> >
> >
> >
> >
> >
>
>
> --
> Best Regards,
>
> Tolulope.
>
>
> Blogs and organic groups at http://www.ccie.net
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html

Blogs and organic groups at http://www.ccie.net
Received on Fri Feb 19 2010 - 17:54:07 ART