Re: L3 etherchannel Dynamips

Hi,
Dynamips does NOT emulate switches or ISRs.
The NM16ESW module is still NOT a switch :-)

Configuration features of the Etherswitch module are documented here:

http://www.cisco.com/en/US/docs/ios/lanswitch/configuration/guide/lsw_enet_switch_net_ps6350_TSD_Products_Configuration_Guide_Chapter.html

The NM16ESW does not support layer 3 etherchannels.

On 2/19/10, Edmore Chingwena <chingwenaed_at_gmail.com> wrote:
> Hi Guys
>
> Any help on the issue below I am experiencing any ideas
>
> Rack1SW2(config)#int po2
> Rack1SW2(config-if)#ip address 155.1.108.8 255.255.255.0
>
> % IP addresses may not be configured on L2 links.
>
> Rack1SW2(config-if)#no switchport
> Command rejected: not allowed under port channel.
> Rack1SW2(config-if)#
>
> Rack1SW2(config-if)#do show run int port 2
> Building configuration...
>
> Current configuration : 31 bytes
> !
> interface Port-channel2
> end
>
> Rack1SW2(config-if)#do show run int fa 1/13
> Building configuration...
>
> Current configuration : 59 bytes
> !
> interface FastEthernet1/13
> channel-group 2 mode on
> end
>
> Rack1SW2(config-if)#do show run int fa 1/14
> Building configuration...
>
> Current configuration : 59 bytes
> !
> interface FastEthernet1/14
> channel-group 2 mode on
> end
>
> Rack1SW2(config-if)#do show run int fa 1/15
> Building configuration...
>
> Current configuration : 59 bytes
> !
> interface FastEthernet1/15
> channel-group 2 mode on
> end
>
> Rack1SW2(config-if)#do show int port 2
> Port-channel2 is up, line protocol is up
> Hardware is EtherChannel, address is c20a.0da8.f10f (bia c20a.0da8.f10f)
> MTU 1500 bytes, BW 300000 Kbit/sec, DLY 1000 usec,
> reliability 255/255, txload 1/255, rxload 1/255
> Encapsulation ARPA, loopback not set
> Keepalive set (10 sec)
> Auto-duplex, Auto-speed
> Members in this channel: Fa1/13 Fa1/14 Fa1/15
> ARP type: ARPA, ARP Timeout 04:00:00
> Last input 00:00:01, output never, output hang never
> Last clearing of "show interface" counters never
> Input queue: 39/75/370/0 (size/max/drops/flushes); Total output drops: 0
> Queueing strategy: fifo
> Output queue: 0/40 (size/max)
> 5 minute input rate 0 bits/sec, 0 packets/sec
> 5 minute output rate 0 bits/sec, 0 packets/sec
> 0 packets input, 0 bytes, 0 no buffer
> Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
> 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
> 0 input packets with dribble condition detected
> 0 packets output, 0 bytes, 0 underruns
> 0 output errors, 0 collisions, 1 interface resets
> 0 unknown protocol drops
> 0 babbles, 0 late collision, 0 deferred
> 0 lost carrier, 0 no carrier
> 0 output buffer failures, 0 output buffers swapped out
> Rack1SW2(config-if)#do show version
> Cisco IOS Software, 3700 Software (C3725-ADVENTERPRISEK9-M), Version
> 12.4(15)T10, RELEASE SOFTWARE (fc3)
> Technical Support: http://www.cisco.com/techsupport
> Copyright (c) 1986-2009 by Cisco Systems, Inc.
> Compiled Mon 14-Sep-09 15:53 by prod_rel_team
>
>
> Blogs and organic groups at http://www.ccie.net
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
>
>
>
>
>
>
>

-- 
Best Regards,
Tolulope.
Blogs and organic groups at http://www.ccie.net