From: marc fernandez (mag08036@yahoo.com)
Date: Sat Oct 14 2006 - 13:38:47 ART
Tried all of the steps below. Including output
interpretor but I'm still getting the following error
after image download. Any comments or ideas on what to
do?
Error : Uncompression of the image failed.
invalid compressed data--format violated
Error : zip decompress failed
*** System received a Software forced crash ***
signal= 0x17, code= 0x7, context= 0x8000eac0
PC = 0x800080d4, Cause = 0x20, Status Reg = 0x3041f003
-marc
--- Victor Cappuccio <cvictor@protokolgroup.com>
wrote:
> Paste that information in the Cisco Output
> interpreter
>
https://www.cisco.com/pcgi-bin/Support/OutputInterpreter/home.pl
>
> ERROR: A 'Software-forced Crash' error occurs when
> the router detects a
> severe, unrecoverable error, and reloads itself to
> prevent transmission of
> corrupt data.
>
> This error may be caused by watchdog timeouts, low
> memory, corrupt software
> image,or hardware problems.
>
> TRY THIS: (please note that there are URLs in the
> following text, so go to
> OInterpreter Page to check out detail information)
>
> 1. Please refer to TAC Case Collection -
> Software-forced crash for
> troubleshooting.
> 2. If the "Error : pre and post compression image
> sizes disagree" console
> message is displayed along with 'Software forced
> crash' message, please
> refer
> to TAC Case Collection - Software-forced crash
> (pre and post compression)
> for
> troubleshooting.
> 3. If the "Not enough memory in the system to run
> this image" console
> message is displayed along with the
> 'Software-forced Crash' message,
> please refer
> to TAC Case Collection - Software-forced crash
> (not enough memory) for
> troubleshooting.
> REFERENCE: For more information, see Understanding
> Software-forced Crashes.
>
> REFERENCE: For more information, see:
> Troubleshooting Router Crashes
> Less Common Types of System Crashes
>
>
>
> -----Mensaje original-----
> De: nobody@groupstudy.com
> [mailto:nobody@groupstudy.com] En nombre de marc
> fernandez
> Enviado el: Viernes, 13 de Octubre de 2006 10:40
> p.m.
> Para: ccielab@groupstudy.com
> Asunto: 3640 will not load image
>
> I have a 3640 which had no mem or flash and would
> not
> boot. I upgraded it to 128D/32F. Tried to download
> flash via xmodem but image still won't load. I now
> can
> only access it via rommon. Does anyone have any
> answers in regards to what I am doing wrong or what
> is
> wrong? below is the constant reboot I get after a
> reset as there is no image on the box when I do a
> dir.
> I need help desperatly.
>
> rommon 2 > reset
>
> System Bootstrap, Version 11.1(20)AA2, EARLY
> DEPLOYMENT RELEASE SOFTWARE (fc1)
> Copyright (c) 1999 by cisco Systems, Inc.
> C3600 processor with 131072 Kbytes of main memory
> Main memory is configured to 64 bit mode with parity
> disabled
>
> program load complete, entry point: 0x80008000,
> size:
> 0x1a7a6f8
> Self decompressing the image :
> Error : Uncompression of the image failed.
> invalid compressed data--format violated
>
> Error : zip decompress failed
>
> *** System received a Software forced crash ***
> signal= 0x17, code= 0x7, context= 0x8000eb40
> PC = 0x800080d4, Cause = 0x20, Status Reg =
> 0x3041f003
>
> System Bootstrap, Version 11.1(20)AA2, EARLY
> DEPLOYMENT RELEASE SOFTWARE (fc1)
> Copyright (c) 1999 by cisco Systems, Inc.
> C3600 processor with 131072 Kbytes of main memory
> Main memory is configured to 64 bit mode with parity
> disabled
>
> PCMCIA Slot0: No Card Present
>
> System Bootstrap, Version 11.1(20)AA2, EARLY
> DEPLOYMENT RELEASE SOFTWARE (fc1)
> Copyright (c) 1999 by cisco Systems, Inc.
>
>
>
> -marc
>
> __________________________________________________
> Do You Yahoo!?
> Tired of spam? Yahoo! Mail has the best spam
> protection around
> http://mail.yahoo.com
>
>
This archive was generated by hypermail 2.1.4 : Wed Nov 01 2006 - 07:29:05 ART