From: Victor Cappuccio (cvictor@protokolgroup.com)
Date: Sat Oct 14 2006 - 13:52:41 ART
Yes did you tried this:
=======
De: nobody@groupstudy.com [mailto:nobody@groupstudy.com] En nombre de Brad
Ellis
Enviado el: Sabado, 14 de Octubre de 2006 12:38 a.m.
Para: marc fernandez; ccielab@groupstudy.com
Asunto: Re: 3640 will not load image [bcc][faked-from]
I've seen this before...try the following:
1) re-download a very small ip only 3640 image and try that
if (1) doesnt work, then (2) try replacing the dram and try the upgrade
again
if (2) doesnt work, then (3) try replacing the flash (although it doesnt
appear to be a flash issue)
thanks,
Brad Ellis
CCIE#5796 (R&S / Security)
CCSI#30482
Network Learning Inc - A Cisco Sponsored Organization (SO)
YES! We take Cisco Learning credits!
brad@ccbootcamp.com
www.ccbootcamp.com (Cisco Training and Advanced Technology Rental Racks)
Voice: 702-968-5100
FAX: 702-446-8012
-----Mensaje original-----
De: marc fernandez [mailto:mag08036@yahoo.com]
Enviado el: Sabado, 14 de Octubre de 2006 12:39 p.m.
Para: Victor Cappuccio; ccielab@groupstudy.com
Asunto: RE: 3640 will not load image
Tried all of the steps below. Including output
interpretor but I'm still getting the following error
after image download. Any comments or ideas on what to
do?
Error : Uncompression of the image failed.
invalid compressed data--format violated
Error : zip decompress failed
*** System received a Software forced crash ***
signal= 0x17, code= 0x7, context= 0x8000eac0
PC = 0x800080d4, Cause = 0x20, Status Reg = 0x3041f003
-marc
--- Victor Cappuccio <cvictor@protokolgroup.com>
wrote:
> Paste that information in the Cisco Output
> interpreter
>
https://www.cisco.com/pcgi-bin/Support/OutputInterpreter/home.pl
>
> ERROR: A 'Software-forced Crash' error occurs when
> the router detects a
> severe, unrecoverable error, and reloads itself to
> prevent transmission of
> corrupt data.
>
> This error may be caused by watchdog timeouts, low
> memory, corrupt software
> image,or hardware problems.
>
> TRY THIS: (please note that there are URLs in the
> following text, so go to
> OInterpreter Page to check out detail information)
>
> 1. Please refer to TAC Case Collection -
> Software-forced crash for
> troubleshooting.
> 2. If the "Error : pre and post compression image
> sizes disagree" console
> message is displayed along with 'Software forced
> crash' message, please
> refer
> to TAC Case Collection - Software-forced crash
> (pre and post compression)
> for
> troubleshooting.
> 3. If the "Not enough memory in the system to run
> this image" console
> message is displayed along with the
> 'Software-forced Crash' message,
> please refer
> to TAC Case Collection - Software-forced crash
> (not enough memory) for
> troubleshooting.
> REFERENCE: For more information, see Understanding
> Software-forced Crashes.
>
> REFERENCE: For more information, see:
> Troubleshooting Router Crashes
> Less Common Types of System Crashes
>
>
>
> -----Mensaje original-----
> De: nobody@groupstudy.com
> [mailto:nobody@groupstudy.com] En nombre de marc
> fernandez
> Enviado el: Viernes, 13 de Octubre de 2006 10:40
> p.m.
> Para: ccielab@groupstudy.com
> Asunto: 3640 will not load image
>
> I have a 3640 which had no mem or flash and would
> not
> boot. I upgraded it to 128D/32F. Tried to download
> flash via xmodem but image still won't load. I now
> can
> only access it via rommon. Does anyone have any
> answers in regards to what I am doing wrong or what
> is
> wrong? below is the constant reboot I get after a
> reset as there is no image on the box when I do a
> dir.
> I need help desperatly.
>
> rommon 2 > reset
>
> System Bootstrap, Version 11.1(20)AA2, EARLY
> DEPLOYMENT RELEASE SOFTWARE (fc1)
> Copyright (c) 1999 by cisco Systems, Inc.
> C3600 processor with 131072 Kbytes of main memory
> Main memory is configured to 64 bit mode with parity
> disabled
>
> program load complete, entry point: 0x80008000,
> size:
> 0x1a7a6f8
> Self decompressing the image :
> Error : Uncompression of the image failed.
> invalid compressed data--format violated
>
> Error : zip decompress failed
>
> *** System received a Software forced crash ***
> signal= 0x17, code= 0x7, context= 0x8000eb40
> PC = 0x800080d4, Cause = 0x20, Status Reg =
> 0x3041f003
>
> System Bootstrap, Version 11.1(20)AA2, EARLY
> DEPLOYMENT RELEASE SOFTWARE (fc1)
> Copyright (c) 1999 by cisco Systems, Inc.
> C3600 processor with 131072 Kbytes of main memory
> Main memory is configured to 64 bit mode with parity
> disabled
>
> PCMCIA Slot0: No Card Present
>
> System Bootstrap, Version 11.1(20)AA2, EARLY
> DEPLOYMENT RELEASE SOFTWARE (fc1)
> Copyright (c) 1999 by cisco Systems, Inc.
>
>
>
> -marc
>
> __________________________________________________
> Do You Yahoo!?
> Tired of spam? Yahoo! Mail has the best spam
> protection around
> http://mail.yahoo.com
>
>
This archive was generated by hypermail 2.1.4 : Wed Nov 01 2006 - 07:29:05 ART