From: marc fernandez (mag08036@yahoo.com)
Date: Sat Oct 14 2006 - 14:14:10 ART
I tried everything below. I can see the image on the
box and the meminfo shows the correct information. But
it still won't boot. Below is the output.
rommon 5 > meminfo
Main memory size: 128 MB in 64 bit mode.
Available main memory starts at 0xa000e000, size
131016KB
IO (packet) memory size: 6 percent of main memory.
NVRAM size: 128KB
rommon 6 > dir flash:
File size Checksum File name
6314736 bytes (0x605af0) 0x117c
c3640-i-mz.122-37.bin
-marc
--- Victor Cappuccio <cvictor@protokolgroup.com>
wrote:
> Yes did you tried this:
>
> =======
>
> De: nobody@groupstudy.com
> [mailto:nobody@groupstudy.com] En nombre de Brad
> Ellis
> Enviado el: Sabado, 14 de Octubre de 2006 12:38 a.m.
> Para: marc fernandez; ccielab@groupstudy.com
> Asunto: Re: 3640 will not load image
> [bcc][faked-from]
>
> I've seen this before...try the following:
>
> 1) re-download a very small ip only 3640 image and
> try that
> if (1) doesnt work, then (2) try replacing the dram
> and try the upgrade
> again
> if (2) doesnt work, then (3) try replacing the flash
> (although it doesnt
> appear to be a flash issue)
>
> thanks,
> Brad Ellis
> CCIE#5796 (R&S / Security)
> CCSI#30482
> Network Learning Inc - A Cisco Sponsored
> Organization (SO)
> YES! We take Cisco Learning credits!
> brad@ccbootcamp.com
> www.ccbootcamp.com (Cisco Training and Advanced
> Technology Rental Racks)
> Voice: 702-968-5100
> FAX: 702-446-8012
>
>
> -----Mensaje original-----
> De: marc fernandez [mailto:mag08036@yahoo.com]
> Enviado el: Sabado, 14 de Octubre de 2006 12:39 p.m.
> Para: Victor Cappuccio; ccielab@groupstudy.com
> Asunto: RE: 3640 will not load image
>
> Tried all of the steps below. Including output
> interpretor but I'm still getting the following
> error
> after image download. Any comments or ideas on what
> to
> do?
>
> Error : Uncompression of the image failed.
> invalid compressed data--format violated
>
> Error : zip decompress failed
>
> *** System received a Software forced crash ***
> signal= 0x17, code= 0x7, context= 0x8000eac0
> PC = 0x800080d4, Cause = 0x20, Status Reg =
> 0x3041f003
>
> -marc
>
> --- Victor Cappuccio <cvictor@protokolgroup.com>
> wrote:
>
> > Paste that information in the Cisco Output
> > interpreter
> >
>
https://www.cisco.com/pcgi-bin/Support/OutputInterpreter/home.pl
> >
> > ERROR: A 'Software-forced Crash' error occurs when
> > the router detects a
> > severe, unrecoverable error, and reloads itself to
> > prevent transmission of
> > corrupt data.
> >
> > This error may be caused by watchdog timeouts, low
> > memory, corrupt software
> > image,or hardware problems.
> >
> > TRY THIS: (please note that there are URLs in the
> > following text, so go to
> > OInterpreter Page to check out detail information)
> >
> > 1. Please refer to TAC Case Collection -
> > Software-forced crash for
> > troubleshooting.
> > 2. If the "Error : pre and post compression image
> > sizes disagree" console
> > message is displayed along with 'Software
> forced
> > crash' message, please
> > refer
> > to TAC Case Collection - Software-forced crash
> > (pre and post compression)
> > for
> > troubleshooting.
> > 3. If the "Not enough memory in the system to run
> > this image" console
> > message is displayed along with the
> > 'Software-forced Crash' message,
> > please refer
> > to TAC Case Collection - Software-forced crash
> > (not enough memory) for
> > troubleshooting.
> > REFERENCE: For more information, see Understanding
> > Software-forced Crashes.
> >
> > REFERENCE: For more information, see:
> > Troubleshooting Router Crashes
> > Less Common Types of System Crashes
> >
> >
> >
> > -----Mensaje original-----
> > De: nobody@groupstudy.com
> > [mailto:nobody@groupstudy.com] En nombre de marc
> > fernandez
> > Enviado el: Viernes, 13 de Octubre de 2006 10:40
> > p.m.
> > Para: ccielab@groupstudy.com
> > Asunto: 3640 will not load image
> >
> > I have a 3640 which had no mem or flash and would
> > not
> > boot. I upgraded it to 128D/32F. Tried to
> download
> > flash via xmodem but image still won't load. I now
> > can
> > only access it via rommon. Does anyone have any
> > answers in regards to what I am doing wrong or
> what
> > is
> > wrong? below is the constant reboot I get after a
> > reset as there is no image on the box when I do a
> > dir.
> > I need help desperatly.
> >
> > rommon 2 > reset
> >
> > System Bootstrap, Version 11.1(20)AA2, EARLY
> > DEPLOYMENT RELEASE SOFTWARE (fc1)
> > Copyright (c) 1999 by cisco Systems, Inc.
> > C3600 processor with 131072 Kbytes of main memory
> > Main memory is configured to 64 bit mode with
> parity
> > disabled
> >
> > program load complete, entry point: 0x80008000,
> > size:
> > 0x1a7a6f8
> > Self decompressing the image :
> > Error : Uncompression of the image failed.
> > invalid compressed data--format violated
> >
> > Error : zip decompress failed
> >
> > *** System received a Software forced crash ***
> > signal= 0x17, code= 0x7, context= 0x8000eb40
> > PC = 0x800080d4, Cause = 0x20, Status Reg =
> > 0x3041f003
> >
> > System Bootstrap, Version 11.1(20)AA2, EARLY
> > DEPLOYMENT RELEASE SOFTWARE (fc1)
> > Copyright (c) 1999 by cisco Systems, Inc.
> > C3600 processor with 131072 Kbytes of main memory
> > Main memory is configured to 64 bit mode with
> parity
> > disabled
> >
> > PCMCIA Slot0: No Card Present
> >
> > System Bootstrap, Version 11.1(20)AA2, EARLY
> > DEPLOYMENT RELEASE SOFTWARE (fc1)
> > Copyright (c) 1999 by cisco Systems, Inc.
> >
> >
> >
> > -marc
> >
> > __________________________________________________
> > Do You Yahoo!?
> > Tired of spam? Yahoo! Mail has the best spam
> > protection around
> > http://mail.yahoo.com
> >
> >
>
This archive was generated by hypermail 2.1.4 : Wed Nov 01 2006 - 07:29:05 ART