From: Andy Tang (andytang88@gmail.com)
Date: Tue Jun 28 2005 - 15:30:48 GMT-3
Hi Brian,
I tried to install on two 2620 routers and got the same error message but I
installed on two 2610 routers without any problem. I am appreciated if you
can advise the solution.
=======================
rommon 5 > tftpdnld -r
IP_ADDRESS: 10.10.10.1 <http://10.10.10.1>
IP_SUBNET_MASK: 255.255.255.0 <http://255.255.255.0>
DEFAULT_GATEWAY: 10.10.10.10 <http://10.10.10.10>
TFTP_SERVER: 10.10.10.10 <http://10.10.10.10>
TFTP_FILE: c2600-js-mz.122-15.T16.bin
....
ARP: address resolution for 10.10.10.10 <http://10.10.10.10> timed out.
ARP failed with failure code 1. TFTP transfer aborted.
TFTP: Operation terminated prematurely.
rommon 6 >
-------------
Rack1R1#s ver
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-J1S3-M), Version 12.2(15)T14, RELEASE
SOFTWARE (fc4)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2004 by cisco Systems, Inc.
Compiled Sat 28-Aug-04 06:47 by cmong
Image text-base: 0x80008098, data-base: 0x819608A4
ROM: System Bootstrap, Version 12.2(10r)1, RELEASE SOFTWARE (fc1)
ROM: C2600 Software (C2600-J1S3-M), Version 12.2(15)T14, RELEASE SOFTWARE
(fc4)
Rack1R1 uptime is 1 minute
System returned to ROM by reload
System image file is "flash:c2600-j1s3-mz.122-15.T14.bin"
cisco 2620 (MPC860) processor (revision 0x00) with 61440K/4096K bytes of
memory.
Processor board ID JAD0652010H (336793937)
M860 processor: part number 0, mask 49
Bridging software.
X.25 software, Version 3.0.0.
TN3270 Emulation software.
1 FastEthernet/IEEE 802.3 interface(s)
2 Serial(sync/async) network interface(s)
32K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read/Write)
Configuration register is 0x2102
Rack1R1#
======================
rommon 2 > tftpdnld -r
IP_ADDRESS: 10.10.10.6 <http://10.10.10.6>
IP_SUBNET_MASK: 255.255.255.0 <http://255.255.255.0>
DEFAULT_GATEWAY: 10.10.10.10 <http://10.10.10.10>
TFTP_SERVER: 10.10.10.10 <http://10.10.10.10>
TFTP_FILE: c2600-js-mz.22-15.T16.bin
....
ARP: address resolution for 10.10.10.10 <http://10.10.10.10> timed out.
ARP failed with failure code 1. TFTP transfer aborted.
TFTP: Operation terminated prematurely.
rommon 3 >
-------------
Rack1R6#s ver
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-J1S3-M), Version 12.2(15)T14, RELEASE
SOFTWARE (fc4)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2004 by cisco Systems, Inc.
Compiled Sat 28-Aug-04 06:47 by cmong
Image text-base: 0x80008098, data-base: 0x819608A4
ROM: System Bootstrap, Version 12.1(3r)T2, RELEASE SOFTWARE (fc1)
ROM: C2600 Software (C2600-J1S3-M), Version 12.2(15)T14, RELEASE SOFTWARE
(fc4)
Rack1R6 uptime is 2 minutes
System returned to ROM by reload
System image file is "flash:c2600-j1s3-mz.122-15.T14.bin"
cisco 2620 (MPC860) processor (revision 0x600) with 61440K/4096K bytes of
memory.
Processor board ID JAD060707XL (497589208)
M860 processor: part number 0, mask 49
Bridging software.
X.25 software, Version 3.0.0.
TN3270 Emulation software.
1 FastEthernet/IEEE 802.3 interface(s)
1 Serial network interface(s)
32K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read/Write)
Configuration register is 0x2102
Rack1R6#
========
Thanks & regards,
Andy
On 6/28/05, Brian McGahan <bmcgahan@internetworkexpert.com> wrote:
>
> Andy,
>
> I believe it depends on the bootrom version. Try it out and see
> what happens. If it doesn't work post the error messages and your "show
> version" output.
>
> HTH,
>
> Brian McGahan, CCIE #8593
> bmcgahan@internetworkexpert.com
>
> Internetwork Expert, Inc.
> http://www.InternetworkExpert.com
> Toll Free: 877-224-8987 x 705
> Outside US: 775-826-4344 x 705
> 24/7 Support: http://forum.internetworkexpert.com
> Live Chat: http://www.internetworkexpert.com/chat/
>
>
> > -----Original Message-----
> > From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf
> Of
> > Andy Tang
> > Sent: Monday, June 27, 2005 9:13 PM
> > To: Brian McGahan
> > Cc: Chad Hintz; Mathew; Cisco certification
> > Subject: Re: Command "ipv6 ospf" on 2600 with IOS 12.2(15)T15
> >
> > Hi Brian,
> > Can I boot the enterprise plus image c2600-js-mz.122-15.T16.bin from
> TFTP
> > to the 2620 64MD/16F via the "tftpdnld -r" command in rommon?
> > Thanks & regards,
> > Andy
> >
> > On 5/25/05, Brian McGahan <bmcgahan@internetworkexpert.com> wrote:
> > >
> > > You can boot the 2600XM enterprise plus image from TFTP to the 2610
> or
> > > 2611 via the "tftpdnld -r" command in rommon.
> > >
> > > HTH,
> > >
> > > Brian McGahan, CCIE #8593
> > > bmcgahan@internetworkexpert.com
> > >
> > > Internetwork Expert, Inc.
> > > http://www.InternetworkExpert.com
> > > Toll Free: 877-224-8987 x 705
> > > Outside US: 775-826-4344 x 705
> > > 24/7 Support: http://forum.internetworkexpert.com
> > > Live Chat: http://www.internetworkexpert.com/chat/
> > >
> > >
> > > > -----Original Message-----
> > > > From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On
> Behalf
> > > Of
> > > > Chad Hintz
> > > > Sent: Tuesday, May 24, 2005 7:11 AM
> > > > To: Mathew; 'Cisco certification'
> > > > Subject: Re: Command "ipv6 ospf" on 2600 with IOS 12.2(15)T15
> > > >
> > > > The 2610 does not support this feature, you need a 2620 or 21 to
> use
> > > > ospfv3.
> > > >
> > > > HTH,
> > > >
> > > > Chad
> > > >
> > > >
> > > > Hi Team
> > > >
> > > > Does anybody know why I can not enable IPV6 OSPF on 2600 with IOS
> ver
> > > > 12.2(15)T15?
> > > >
> > > > Even after configuring "ipv6 unicast-routing" and "ipv6 enable"
> under
> > > the
> > > > interface, I do not see
> > > >
> > > > a OSPF option.
> > > >
> > > > Does anybody know why it is so?
> > > >
> > > > R2(config-if)#ipv6 ?
> > > > IPv6 interface subcommands:
> > > > address Configure IPv6 address on interface
> > > > cef Cisco Express Forwarding for IPv6
> > > > enable Enable IPv6 on interface
> > > > mtu Set IPv6 Maximum Transmission Unit
> > > > nat Enable IPv6 NAT on interface
> > > > nd IPv6 interface Neighbor Discovery subcommands
> > > > redirects Enable sending of ICMP Redirect messages
> > > > rip Configure RIP routing protocol
> > > > router IPv6 Router interface commands
> > > > traffic-filter Access control list for packets
> > > > unnumbered Preferred interface for source address selection
> > > > verify Enable per packet validation
> > > >
> > > > R2(config-if)#ipv6 ro
> > > > R2(config-if)#ipv6 router ?
> > > > isis IS-IS Routing for IPv6
> > > >
> > > > R2(config-if)#ipv6 router
> > > > R2(config-if)#do sho ver
> > > > Cisco Internetwork Operating System Software
> > > > IOS (tm) C2600 Software (C2600-J1S3-M), Version 12.2(15)T15,
> RELEASE
> > > > SOFTWARE (fc1)
> > > > Technical Support: http://www.cisco.com/techsupport
> > > > Copyright (c) 1986-2005 by cisco Systems, Inc.
> > > > Compiled Thu 03-Mar-05 03:28 by hqluong
> > > > Image text-base: 0x80008098, data-base: 0x81960D40
> > > >
> > > > ROM: System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)
> > > > ROM: C2600 Software (C2600-J1S3-M), Version 12.2(15)T15, RELEASE
> > > SOFTWARE
> > > > (fc1)
> > > >
> > > > R2 uptime is 47 minutes
> > > > System returned to ROM by power-on
> > > > System image file is "flash:c2600-j1s3-mz.122-15.T15.bin"
> > > >
> > > > cisco 2610 (MPC860) processor (revision 0x203) with 61440K/4096K
> bytes
> > > of
> > > > memory.
> > > > Processor board ID JAD05090GQQ (1222274526)
> > > > M860 processor: part number 0, mask 49
> > > > Bridging software.
> > > > X.25 software, Version 3.0.0.
> > > > TN3270 Emulation software.
> > > > 1 Ethernet/IEEE 802.3 interface(s)
> > > > 2 Serial(sync/async) network interface(s)
> > > > 16 terminal line(s)
> > > > 32K bytes of non-volatile configuration memory.
> > > > 16384K bytes of processor board System flash (Read/Write)
> > > >
> > > > Configuration register is 0x2102
> > > >
> > > > R2(config-if)#
> > > >
> > > >
> > >
> _______________________________________________________________________
> > > > Subscription information may be found at:
> > > > http://www.groupstudy.com/list/CCIELab.html
> > > >
> > > > __________________________________________________
> > > > Do You Yahoo!?
> > > > Tired of spam? Yahoo! Mail has the best spam protection around
> > > > http://mail.yahoo.com
> > > >
> > > >
> > >
> _______________________________________________________________________
> > > > Subscription information may be found at:
> > > > http://www.groupstudy.com/list/CCIELab.html
> > >
> > >
> _______________________________________________________________________
> > > Subscription information may be found at:
> > > http://www.groupstudy.com/list/CCIELab.html
> >
> >
> _______________________________________________________________________
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Wed Jul 06 2005 - 14:43:45 GMT-3