From: CCIE Group Study (ccie@madisonsolutions.net)
Date: Tue Jun 28 2005 - 12:08:35 GMT-3
Good morning:
I looked into updating a number of 2610 and 2612 (Ethernet and Token Ring).
Both worked.
The design for someone who has not used "tftpdnld" rommon you need a few
items:
Solarwinds TFTP Server, (FREE)
Cisco Enterprise Plus 12.2(T) image for OSPF v3
Start the router
go to rommon with the "control break" keys
At the rommon prompt type:
IP_ADDRESS:=192.168.1.208
IP_SUBNET_MASK= 255.255.255.0
DEFAULT_GATEWAY= 192.168.1.1
TFTP_SERVER=192.168.1.106
TFTP_FILE: c2600-js-mz.122-15.T16.bin
The 192.168.1.0/24 network just happens to be my home network so use want
every IP addresses you need to make your network talk. The Ethernet 0/0
port needs to be conected to the same subnet as your TFTP server.
Make sure that if you are running a Firewall that TFTP is allowed in.
Type the following after you have configured your router:
tftpdnld -r
The -r is the reload command. The router will then do one of two things
succeed, or as one of my routers did failed the check sum during the load.
No matter I was able to load the 12.2(T) Enterprise Plus image on 4 2610 and
2612 and am now working with the Cisco OSPF v3 information loacted at:
http://www.cisco.com/univercd/cc/td/doc/product/software/ios123/123cgcr/ipv6_c/sa_impv6.pdf
The labs that I am creating are:
- OSPF v3
- OSPF v3 over Frame Relay
- RIPng
- IPv6 Tunnels
- IPv6 restribution from RIPng to OSPF v3
Last tip for IPv6 don't get hung-up IPv6 addressing; make it simple:
- R1 Loopback0 11::1/64
- R1 Serial 0/0 12::1/64
- R2 Serial 0/0 12::2/64
- R2 Loopback0 22::2/64
Lat tip the CCIE Proctors read some of these e-Mails. So knowing that thier
is a workaround will only instill in them the desire for more IPv6.
George Morton, Ph. D.
Madison Solutions
----- Original Message -----
From: "Andy Tang" <andytang88@gmail.com>
To: "Brian McGahan" <bmcgahan@internetworkexpert.com>
Cc: "Chad Hintz" <ccie_2b2004@yahoo.com>; "Mathew" <mathew@oztralia.com>;
"Cisco certification" <ccielab@groupstudy.com>
Sent: Tuesday, June 28, 2005 12:13 AM
Subject: Re: Command "ipv6 ospf" on 2600 with IOS 12.2(15)T15
> Hi Brian,
> Can I boot the enterprise plus image c2600-js-mz.122-15.T16.bin from TFTP
> to the 2620 64MD/16F via the "tftpdnld -r" command in rommon?
> Thanks & regards,
> Andy
>
> On 5/25/05, Brian McGahan <bmcgahan@internetworkexpert.com> wrote:
>>
>> You can boot the 2600XM enterprise plus image from TFTP to the 2610 or
>> 2611 via the "tftpdnld -r" command in rommon.
>>
>> HTH,
>>
>> Brian McGahan, CCIE #8593
>> bmcgahan@internetworkexpert.com
>>
>> Internetwork Expert, Inc.
>> http://www.InternetworkExpert.com
>> Toll Free: 877-224-8987 x 705
>> Outside US: 775-826-4344 x 705
>> 24/7 Support: http://forum.internetworkexpert.com
>> Live Chat: http://www.internetworkexpert.com/chat/
>>
>>
>> > -----Original Message-----
>> > From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf
>> Of
>> > Chad Hintz
>> > Sent: Tuesday, May 24, 2005 7:11 AM
>> > To: Mathew; 'Cisco certification'
>> > Subject: Re: Command "ipv6 ospf" on 2600 with IOS 12.2(15)T15
>> >
>> > The 2610 does not support this feature, you need a 2620 or 21 to use
>> > ospfv3.
>> >
>> > HTH,
>> >
>> > Chad
>> >
>> >
>> > Hi Team
>> >
>> > Does anybody know why I can not enable IPV6 OSPF on 2600 with IOS ver
>> > 12.2(15)T15?
>> >
>> > Even after configuring "ipv6 unicast-routing" and "ipv6 enable" under
>> the
>> > interface, I do not see
>> >
>> > a OSPF option.
>> >
>> > Does anybody know why it is so?
>> >
>> > R2(config-if)#ipv6 ?
>> > IPv6 interface subcommands:
>> > address Configure IPv6 address on interface
>> > cef Cisco Express Forwarding for IPv6
>> > enable Enable IPv6 on interface
>> > mtu Set IPv6 Maximum Transmission Unit
>> > nat Enable IPv6 NAT on interface
>> > nd IPv6 interface Neighbor Discovery subcommands
>> > redirects Enable sending of ICMP Redirect messages
>> > rip Configure RIP routing protocol
>> > router IPv6 Router interface commands
>> > traffic-filter Access control list for packets
>> > unnumbered Preferred interface for source address selection
>> > verify Enable per packet validation
>> >
>> > R2(config-if)#ipv6 ro
>> > R2(config-if)#ipv6 router ?
>> > isis IS-IS Routing for IPv6
>> >
>> > R2(config-if)#ipv6 router
>> > R2(config-if)#do sho ver
>> > Cisco Internetwork Operating System Software
>> > IOS (tm) C2600 Software (C2600-J1S3-M), Version 12.2(15)T15, RELEASE
>> > SOFTWARE (fc1)
>> > Technical Support: http://www.cisco.com/techsupport
>> > Copyright (c) 1986-2005 by cisco Systems, Inc.
>> > Compiled Thu 03-Mar-05 03:28 by hqluong
>> > Image text-base: 0x80008098, data-base: 0x81960D40
>> >
>> > ROM: System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)
>> > ROM: C2600 Software (C2600-J1S3-M), Version 12.2(15)T15, RELEASE
>> SOFTWARE
>> > (fc1)
>> >
>> > R2 uptime is 47 minutes
>> > System returned to ROM by power-on
>> > System image file is "flash:c2600-j1s3-mz.122-15.T15.bin"
>> >
>> > cisco 2610 (MPC860) processor (revision 0x203) with 61440K/4096K bytes
>> of
>> > memory.
>> > Processor board ID JAD05090GQQ (1222274526)
>> > M860 processor: part number 0, mask 49
>> > Bridging software.
>> > X.25 software, Version 3.0.0.
>> > TN3270 Emulation software.
>> > 1 Ethernet/IEEE 802.3 interface(s)
>> > 2 Serial(sync/async) network interface(s)
>> > 16 terminal line(s)
>> > 32K bytes of non-volatile configuration memory.
>> > 16384K bytes of processor board System flash (Read/Write)
>> >
>> > Configuration register is 0x2102
>> >
>> > R2(config-if)#
>> >
>> >
>> _______________________________________________________________________
>> > Subscription information may be found at:
>> > http://www.groupstudy.com/list/CCIELab.html
>> >
>> > __________________________________________________
>> > Do You Yahoo!?
>> > Tired of spam? Yahoo! Mail has the best spam protection around
>> > http://mail.yahoo.com
>> >
>> >
>> _______________________________________________________________________
>> > Subscription information may be found at:
>> > http://www.groupstudy.com/list/CCIELab.html
>>
>> _______________________________________________________________________
>> Subscription information may be found at:
>> http://www.groupstudy.com/list/CCIELab.html
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Wed Jul 06 2005 - 14:43:45 GMT-3