From: Carlos G Mendioroz (tron@huapi.ba.ar)
Date: Sun Jul 11 2004 - 15:39:15 GMT-3
Dre Mema,
this is not always so, depends on your ISDN setup.
(And it is not so in this setup!)
Router should jump to the second string if there was an error on first,
but is not doing so.
Mema Dre wrote:
> keep only one if these two lines:
>
> dialer map ip 172.30.25.5 name R5 broadcast 3333000
> dialer map ip 172.30.25.5 name R5 broadcast 3333001
>
> does not matter which one. Because all the numbers in BRI are in hunt
> group you need only one dialer map. remove second for example and
> everytinh will be fine.
>
> Dre Mema
>
>
>
>
>> From: Carlos G Mendioroz <tron@huapi.ba.ar>
>> Reply-To: Carlos G Mendioroz <tron@huapi.ba.ar>
>> To: Group Study <ccielab@groupstudy.com>
>> Subject: ISDN multilink dialer error
>> Date: Sun, 11 Jul 2004 14:30:09 -0300
>>
>> I'm trying to bring a multilink with 2 channels at once by doing:
>>
>> interface BRI0/0
>> ip address 172.30.25.2 255.255.255.0
>> encapsulation ppp
>> dialer map ip 172.30.25.5 name R5 broadcast 3333000
>> dialer map ip 172.30.25.5 name R5 broadcast 3333001
>> dialer-group 1
>> isdn switch-type basic-dms100
>> isdn spid1 25633320000101 3332000
>> isdn spid2 25633320010101 3332001
>> ppp authentication chap
>> ppp multilink
>> multilink min-links 2
>> end
>>
>> but when triggered, only one channel links, and the following error
>> shows up:
>>
>> 2d21h: BR0/0 DDR: Dialing cause ip (s=172.30.25.2, d=172.30.25.5)
>> 2d21h: BR0/0 DDR: Attempting to dial 3333000
>> 2d21h: %LINK-3-UPDOWN: Interface BRI0/0:1, changed state to up.
>> 2d21h: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state to up
>> 2d21h: Vi1 DDR: Dialer statechange to up
>> 2d21h: Vi1 DDR: Dialer call has been placed
>> 2d21h: Vi1 DDR: dialer protocol up
>> 2d21h: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0/0:1,
>> changed state to up
>> 2d21h: %LINEPROTO-5-UPDOWN: Line protocol on Interface
>> Virtual-Access1, changed state to up
>> 2d21h: BR0/0 DDR: Attempting to dial 3333000
>> 2d21h: %ISDN-6-CONNECT: Interface BRI0/0:1 is now connected to 3333000 R5
>> 2d21h: BRI0/0: wait for isdn carrier timeout, call id=0x8041
>> 2d21h: BR0/0 DDR: Already 1 call(s) in progress on BR0/0, dialing not
>> allowed
>>
>> Where is this "already 1 call" limit coming from ?
>> Tried max-links 2 w/o success.
>> --
>> Carlos G Mendioroz <tron@huapi.ba.ar> LW7 EQI Argentina
>>
>> _______________________________________________________________________
>> Please help support GroupStudy by purchasing your study materials from:
>> http://shop.groupstudy.com
>>
>> Subscription information may be found at:
>> http://www.groupstudy.com/list/CCIELab.html
>
>
> _________________________________________________________________
> FREE pop-up blocking with the new MSN Toolbar get it now!
> http://toolbar.msn.click-url.com/go/onm00200415ave/direct/01/
>
>
-- Carlos G Mendioroz <tron@huapi.ba.ar> LW7 EQI Argentina
This archive was generated by hypermail 2.1.4 : Sun Aug 01 2004 - 10:11:52 GMT-3