Setting up svc in ATM a/c R6 and R9 (svc not showing up)

From: chee-beng lim (dundeeking@hotmail.com)
Date: Mon Feb 09 2004 - 21:54:53 GMT-3

Having problem in setting up svc between R6 and R9 as follow:

R6:
R6#sh run | b ATM
interface ATM0
no ip address
pvc 0/5 qsaal
!
pvc 0/16 ilmi
!
no atm ilmi-keepalive
!
interface ATM0.1 multipoint
ip address 10.10.10.6 255.255.255.0
!
svc ToR9 nsap 47.00918100000000E01E6C4901.999999999999.99
  protocol ip 10.10.10.9
  encapsulation aal5snap
!
atm esi-address 666666666666.66
!
router isis
net 49.0001.6666.6666.6666.00
is-type level-2-only

R6#sh atm ilmi-status

Interface : ATM0 Interface Type : Private UNI (User-side)
ILMI VCC : (0, 16) ILMI Keepalive : Disabled
ILMI State: UpAndNormal
Peer IP Addr: 0.0.0.0 Peer IF Name: ATM0/0/2
Peer MaxVPIbits: 8 Peer MaxVCIbits: 14
Active Prefix(s) :
47.0091.8100.0000.00e0.1e6c.4901
R6#sh atm map
Map list ToR9_ATM0.1 : PERMANENT
ip 10.10.10.9 maps to NSAP 47.00918100000000E01E6C4901.999999999999.99

R6#sh atm vc
           VCD / Peak Avg/Min Burst
Interface Name VPI VCI Type Encaps SC Kbps Kbps Cells
Sts
0 1 0 5 PVC SAAL UBR 155000
  UP
0 2 0 16 PVC ILMI UBR 155000
  UP
R6#

========
R9:
interface ATM3/0
no ip address
no atm ilmi-keepalive
pvc 0/5 qsaal
!
pvc 0/16 ilmi
!
!
interface ATM3/0.1 multipoint
ip address 10.10.10.9 255.255.255.0
atm esi-address 999999999999.99
!
svc ToR6 nsap 47.00918100000000E01E6C4901.666666666666.66
  protocol ip 10.10.10.6
  broadcast
  encapsulation aal5snap
!

router isis
net 49.0001.9999.9999.9999.00
is-type level-2-only
log-adjacency-changes

R9#sh atm map
Map list ToR6_ATM3/0.1 : PERMANENT
ip 10.10.10.6 maps to NSAP 47.00918100000000E01E6C4901.666666666666.66
        , broadcast

R9#sh atm ilmi-status

Interface : ATM3/0 Interface Type : Private UNI (User-side)
ILMI VCC : (0, 16) ILMI Keepalive : Disabled
ILMI State: UpAndNormal
Peer IP Addr: 0.0.0.0 Peer IF Name: ATM0/0/3
Peer MaxVPIbits: 8 Peer MaxVCIbits: 14
Active Prefix(s) :
47.0091.8100.0000.00e0.1e6c.4901
R9#sh atm vc
           VCD / Peak Avg/Min Burst
Interface Name VPI VCI Type Encaps SC Kbps Kbps Cells
Sts
3/0 1 0 5 PVC SAAL UBR 155000
  UP
3/0 2 0 16 PVC ILMI UBR 155000
  UP
R9#

====> trying debug commands on the R6 with output====
R6>enable
R6#show debug
Generic ATM Signalling:
  ATM Signalling Events debugging is on
ATM0 ATM Signalling Event debugging is on
R6#ping 10.10.10.9

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.10.10.9, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)
R6#debug ip packet
IP packet debugging is on
R6#ping 10.10.10.9

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.10.10.9, timeout is 2 seconds:

*Feb 9 18:40:24 UTC: IP: s=10.10.10.6 (local), d=10.10.10.9 (ATM0.1), len
100,g
*Feb 9 18:40:24 UTC: IP: s=10.10.10.6 (local), d=10.10.10.9 (ATM0.1), len
100,.
*Feb 9 18:40:26 UTC: IP: s=10.10.10.6 (local), d=10.10.10.9 (ATM0.1), len
100,g
*Feb 9 18:40:26 UTC: IP: s=10.10.10.6 (local), d=10.10.10.9 (ATM0.1), len
100,.
*Feb 9 18:40:28 UTC: IP: s=10.10.10.6 (local), d=10.10.10.9 (ATM0.1), len
100,g
*Feb 9 18:40:28 UTC: IP: s=10.10.10.6 (local), d=10.10.10.9 (ATM0.1), len
100,.
*Feb 9 18:40:30 UTC: IP: s=10.10.10.6 (local), d=10.10.10.9 (ATM0.1), len
100,g
*Feb 9 18:40:30 UTC: IP: s=10.10.10.6 (local), d=10.10.10.9 (ATM0.1), len
100,.
*Feb 9 18:40:32 UTC: IP: s=10.10.10.6 (local), d=10.10.10.9 (ATM0.1), len
100,g
*Feb 9 18:40:32 UTC: IP: s=10.10.10.6 (local), d=10.10.10.9 (ATM0.1), len
100,.
Success rate is 0 percent (0/5)
R6#

Note: not seeing anything useful in R6 with "debug atm sig-event" when doing
ping to R9

This archive was generated by hypermail 2.1.4 : Fri Mar 05 2004 - 07:13:48 GMT-3