From: chee-beng lim (dundeeking@hotmail.com)
Date: Mon Feb 09 2004 - 22:35:21 GMT-3
Ian,
I am using ipexpert rack for ATM testing; I don't have access to the ATM
switch.
I have tested pvc using pt-to-pt/multipoint and running ISIS a/c them with
no problem.
Am I right to say that SVC availability to the router R6 and R9 dependent on
how the ATM switch is being configured (forgive my ignornance on the limited
ATM knowledge).
Thanks for your response.
>From: "Ian Stong" <istong@stong.org>
>Reply-To: "Ian Stong" <istong@stong.org>
>To: "'chee-beng lim'" <dundeeking@hotmail.com>, <ccielab@groupstudy.com>
>Subject: RE: Setting up svc in ATM a/c R6 and R9 (svc not showing up)
>Date: Mon, 9 Feb 2004 20:17:06 -0500
>
>HI,
>
>Couple of questions for you:
>
>Is the ATM switch configured for the SVC's (do you have the switch
>config)?
>
>Any reason why you don't have broadcast on R6?
>
>What's the reason behind doing multipoint versus point to point?
>
>
>Thanks,
>
>Ian
>www.ccie4u.com
>Rack Rentals and Lab Scenarios starting at $20
>
>
>-----Original Message-----
>From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
>chee-beng lim
>Sent: Monday, February 09, 2004 7:55 PM
>To: ccielab@groupstudy.com
>Subject: Setting up svc in ATM a/c R6 and R9 (svc not showing up)
>
>Having problem in setting up svc between R6 and R9 as follow:
>
>R6:
>R6#sh run | b ATM
>interface ATM0
>no ip address
>pvc 0/5 qsaal
>!
>pvc 0/16 ilmi
>!
>no atm ilmi-keepalive
>!
>interface ATM0.1 multipoint
>ip address 10.10.10.6 255.255.255.0
>!
>svc ToR9 nsap 47.00918100000000E01E6C4901.999999999999.99
> protocol ip 10.10.10.9
> encapsulation aal5snap
>!
>atm esi-address 666666666666.66
>!
>router isis
>net 49.0001.6666.6666.6666.00
>is-type level-2-only
>
>R6#sh atm ilmi-status
>
>Interface : ATM0 Interface Type : Private UNI (User-side)
>ILMI VCC : (0, 16) ILMI Keepalive : Disabled
>ILMI State: UpAndNormal
>Peer IP Addr: 0.0.0.0 Peer IF Name: ATM0/0/2
>Peer MaxVPIbits: 8 Peer MaxVCIbits: 14
>Active Prefix(s) :
>47.0091.8100.0000.00e0.1e6c.4901
>R6#sh atm map
>Map list ToR9_ATM0.1 : PERMANENT
>ip 10.10.10.9 maps to NSAP 47.00918100000000E01E6C4901.999999999999.99
>
>R6#sh atm vc
> VCD / Peak Avg/Min
>Burst
>Interface Name VPI VCI Type Encaps SC Kbps Kbps
>Cells
>Sts
>0 1 0 5 PVC SAAL UBR 155000
> UP
>0 2 0 16 PVC ILMI UBR 155000
> UP
>R6#
>
>
>========
>R9:
>interface ATM3/0
>no ip address
>no atm ilmi-keepalive
>pvc 0/5 qsaal
>!
>pvc 0/16 ilmi
>!
>!
>interface ATM3/0.1 multipoint
>ip address 10.10.10.9 255.255.255.0
>atm esi-address 999999999999.99
>!
>svc ToR6 nsap 47.00918100000000E01E6C4901.666666666666.66
> protocol ip 10.10.10.6
> broadcast
> encapsulation aal5snap
>!
>
>router isis
>net 49.0001.9999.9999.9999.00
>is-type level-2-only
>log-adjacency-changes
>
>R9#sh atm map
>Map list ToR6_ATM3/0.1 : PERMANENT
>ip 10.10.10.6 maps to NSAP 47.00918100000000E01E6C4901.666666666666.66
> , broadcast
>
>R9#sh atm ilmi-status
>
>Interface : ATM3/0 Interface Type : Private UNI (User-side)
>ILMI VCC : (0, 16) ILMI Keepalive : Disabled
>ILMI State: UpAndNormal
>Peer IP Addr: 0.0.0.0 Peer IF Name: ATM0/0/3
>Peer MaxVPIbits: 8 Peer MaxVCIbits: 14
>Active Prefix(s) :
>47.0091.8100.0000.00e0.1e6c.4901
>R9#sh atm vc
> VCD / Peak Avg/Min
>Burst
>Interface Name VPI VCI Type Encaps SC Kbps Kbps
>Cells
>Sts
>3/0 1 0 5 PVC SAAL UBR 155000
> UP
>3/0 2 0 16 PVC ILMI UBR 155000
> UP
>R9#
>
>
>
>====> trying debug commands on the R6 with output====
>R6>enable
>R6#show debug
>Generic ATM Signalling:
> ATM Signalling Events debugging is on
>ATM0 ATM Signalling Event debugging is on
>R6#ping 10.10.10.9
>
>Type escape sequence to abort.
>Sending 5, 100-byte ICMP Echos to 10.10.10.9, timeout is 2 seconds:
>.....
>Success rate is 0 percent (0/5)
>R6#debug ip packet
>IP packet debugging is on
>R6#ping 10.10.10.9
>
>Type escape sequence to abort.
>Sending 5, 100-byte ICMP Echos to 10.10.10.9, timeout is 2 seconds:
>
>*Feb 9 18:40:24 UTC: IP: s=10.10.10.6 (local), d=10.10.10.9 (ATM0.1),
>len
>100,g
>*Feb 9 18:40:24 UTC: IP: s=10.10.10.6 (local), d=10.10.10.9 (ATM0.1),
>len
>100,.
>*Feb 9 18:40:26 UTC: IP: s=10.10.10.6 (local), d=10.10.10.9 (ATM0.1),
>len
>100,g
>*Feb 9 18:40:26 UTC: IP: s=10.10.10.6 (local), d=10.10.10.9 (ATM0.1),
>len
>100,.
>*Feb 9 18:40:28 UTC: IP: s=10.10.10.6 (local), d=10.10.10.9 (ATM0.1),
>len
>100,g
>*Feb 9 18:40:28 UTC: IP: s=10.10.10.6 (local), d=10.10.10.9 (ATM0.1),
>len
>100,.
>*Feb 9 18:40:30 UTC: IP: s=10.10.10.6 (local), d=10.10.10.9 (ATM0.1),
>len
>100,g
>*Feb 9 18:40:30 UTC: IP: s=10.10.10.6 (local), d=10.10.10.9 (ATM0.1),
>len
>100,.
>*Feb 9 18:40:32 UTC: IP: s=10.10.10.6 (local), d=10.10.10.9 (ATM0.1),
>len
>100,g
>*Feb 9 18:40:32 UTC: IP: s=10.10.10.6 (local), d=10.10.10.9 (ATM0.1),
>len
>100,.
>Success rate is 0 percent (0/5)
>R6#
>
>
>Note: not seeing anything useful in R6 with "debug atm sig-event" when
>doing
>ping to R9
>
>_________________________________________________________________
>Download games, logos, wallpapers and lots more at MSN Mobile!
>http://www.msn.com.sg/mobile/
>
>_______________________________________________________________________
>Please help support GroupStudy by purchasing your study materials from:
>http://shop.groupstudy.com
>
>Subscription information may be found at:
>http://www.groupstudy.com/list/CCIELab.html
>
>_______________________________________________________________________
>Please help support GroupStudy by purchasing your study materials from:
>http://shop.groupstudy.com
>
>Subscription information may be found at:
>http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Fri Mar 05 2004 - 07:13:48 GMT-3