From: David Deng (glend_99@yahoo.com)
Date: Sun Dec 28 2003 - 17:07:55 GMT-3
Mike,
--- David Deng <glend_99@yahoo.com> wrote:
> Mike,
>
> The problem does go away, there must be a reason why
> /29 does not work.
Sorry I wasn't thinking, the .9 .6 are in different
subnet. and this requirement of /29 maybe a typo in
the pratice lab, but not sure about it ?
This comes from Lab 36( sample lab of Ipexpert).
>
> Also /29 is what required to setup for the mask of
> the
>
> ip address, any remedy ?
>
> Regards,
> David
> --- Mike Dickson <Mike@dicksonnetworks.com> wrote:
> > 136.10.69.6/29 is in the 136.10.69.0/29 network;
> > 136.10.69.9/29 is in
> > the 135.10.69.8/29 network. Try setting the
> subnet
> > mask to
> > 255.255.255.240 on both interfaces and see if the
> > problem goes away.
> >
> > Mike Dickson
> > CCIE #12281, MCSE+Internet, MCDBA
> > Dickson Network Designs
> > (512) 422-3192 voice (512) 394-0320 fax
> > www.dicksonnetworks.com
> >
> > -----Original Message-----
> > From: David Deng [mailto:glend_99@yahoo.com]
> > Sent: Sunday, December 28, 2003 12:49 AM
> > To: Mike Dickson; ccielab@groupstudy.com
> > Subject: RE: ATM PVC simple question
> >
> > Mike,
> >
> > The other side is just the same except the ip
> > address is swapped.
> >
> > R6-7200# sh int a2/0
> > interface ATM2/0
> > ip address 136.10.69.6 255.255.255.248
> > no atm ilmi-keepalive
> > pvc 1/100
> > protocol ip 136.10.69.9 broadcast
> >
> >
> > I could ping if the loopback addresses are shut on
> > both sides, so it
> > should not be a misconfig of the address.
> >
> > Regards,
> > David
> > --- Mike Dickson <Mike@dicksonnetworks.com> wrote:
> > > Are you sure about your IP and netmask
> > assignments?
> > > The 2 ends of the
> > > PVC aren't on the same subnet.
> > >
> > > Mike Dickson
> > > CCIE #12281, MCSE+Internet, MCDBA
> > > Dickson Network Designs
> > > (512) 422-3192 voice (512) 394-0320 fax
> > www.dicksonnetworks.com
> > >
> > > -----Original Message-----
> > > From: David Deng [mailto:glend_99@yahoo.com]
> > > Sent: Friday, December 26, 2003 11:58 PM
> > > To: ccielab@groupstudy.com
> > > Subject: ATM PVC simple question
> > >
> > > Hi Group,
> > >
> > > Happy Holidays.
> > >
> > > Just have a qick question on the ATM PVC with
> > loopback
> > >
> > > interface problem.
> > >
> > > When Simple config as such will not work as long
> > as the router
> > > Loopback address is up,
> > >
> > > r9-7200#sh run int a2/0
> > > interface ATM2/0
> > > ip address 136.10.69.9 255.255.255.248 no atm
> > ilmi-keepalive pvc
> > > 1/100
> > > protocol ip 136.10.69.6 broadcast
> > >
> > > Here is the output of the debug on icmp while
> > pinging from the
> > > neighbor.
> > > The echo-reply is returned to the loopback
> address
> > of the neighbor,
> > > any suggestion on getting the ping to work w/o
> > shutdown the loopback ?
> > >
> > > *Dec 26 20:33:50: ICMP: echo reply sent, src
> > 136.10.69.9, dst
> > > 136.10.6.6 *Dec 26 20:33:52: ICMP: echo reply
> > sent, src 136.10.69.9,
> > > dst 136.10.6.6 *Dec 26 20:33:54: ICMP: echo
> reply
> > sent, src
> > > 136.10.69.9, dst 136.10.6.6
> > >
> > >
> > > Thanks,
> > > David
> > >
> > >
> > > __________________________________
> > > Do you Yahoo!?
> > > Protect your identity with Yahoo! Mail
> > AddressGuard
> > > http://antispam.yahoo.com/whatsnewfree
> > >
> > >
> >
>
This archive was generated by hypermail 2.1.4 : Sat Jan 03 2004 - 08:25:46 GMT-3