From: Silvio Nunes (silvio_98@hotmail.com)
Date: Fri Nov 21 2003 - 19:44:30 GMT-3
Hi Scott,
I didnt found an option to work with PPPoFR with frame map, only with dlci
command:
R1(config-subif)#frame-relay interface-dlci 120 ?
ppp Use RFC1973 Encapsulation to support PPP over FR
R1(config-subif)#fram map ip 172.16.123.2 120 ?
broadcast Broadcasts should be forwarded to this address
cisco Use CISCO Encapsulation
compress Enable TCP/IP and RTP/IP header compression
ietf Use RFC1490/RFC2427 Encapsulation
nocompress Do not compress TCP/IP headers
payload-compression Use payload compression
rtp RTP header compression parameters
tcp TCP header compression parameters
Any suggestion ?
Regards,
>From: "Scott Morris" <swm@emanon.com>
>Reply-To: <swm@emanon.com>
>To: "'Silvio Nunes'" <silvio_98@hotmail.com>
>Subject: RE: RSVP
>Date: Thu, 20 Nov 2003 16:38:44 -0500
>
>I'm not sure if you saw my post on the subject or not (strange delays on
>things), but you could consider running PPPoFR on each of the DLCI's.
>That can be tied via the frame map, or interface dlci command. And once
>tied, it uses the virtual template interface. And you could have two
>separate RSVP setups that way.
>
>HTH,
>
>
>Scott Morris, CCIE4 (R&S/ISP-Dial/Security/Service Provider) #4713,
>CISSP, JNCIS, et al.
>IPExpert CCIE Program Manager
>IPExpert Sr. Technical Instructor
>swm@emanon.com/smorris@ipexpert.net
>http://www.ipexpert.net
>
>
>-----Original Message-----
>From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
>Silvio Nunes
>Sent: Thursday, November 20, 2003 2:13 PM
>To: asadovnikov@comcast.net; ccielab@groupstudy.com
>Subject: RE: RSVP
>
>
>Thanks all
>
>Bye
>
>
> >From: "asadovnikov" <asadovnikov@comcast.net>
> >To: "'Silvio Nunes'" <silvio_98@hotmail.com>,<ccielab@groupstudy.com>
> >Subject: RE: RSVP
> >Date: Wed, 19 Nov 2003 23:04:20 -0500
> >
> >Can not be done. RSVP is not configurable perVC. Only way to do it is
>
> >to move from multipoint interface with 2 VCs to two point-to-point
> >interfaces, and then configure RSVP on per-subinterface basis.
> >
> >Best regards,
> >Alexei
> >
> >-----Original Message-----
> >From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
>
> >Silvio Nunes
> >Sent: Wednesday, November 19, 2003 7:53 PM
> >To: ccielab@groupstudy.com
> >Subject: RSVP
> >
> >
> >Guys,
> >
> >I need a help about how to configure RSVP for differents DLCIs, for
> >example:
> >
> >Interface Seria0/0
> >ip add 10.10.10.1 255.255.255.0
> >no frame-relay inverse-arp
> >no arp frame-relay
> >frame-relay map ip 10.10.10.2 110 broadcast
> >frame-relay map ip 10.10.10.3 111 broadcast
> >
> >I want to specify a different RSVP configuration for each DLCI, but I
> >didnt find an option into map-class frame-relay..
> >
> >Any suggestion ?
> >Regards,
> >
> >_________________________________________________________________
> >MSN Hotmail, o maior webmail do Brasil. http://www.hotmail.com
> >
> >_______________________________________________________________________
> >Please help support GroupStudy by purchasing your study materials from:
>
> >http://shop.groupstudy.com
> >
> >Subscription information may be found at:
> >http://www.groupstudy.com/list/CCIELab.html
> >
> >
>
>_________________________________________________________________
>MSN Hotmail, o maior webmail do Brasil. http://www.hotmail.com
>
>_______________________________________________________________________
>Please help support GroupStudy by purchasing your study materials from:
>http://shop.groupstudy.com
>
>Subscription information may be found at:
>http://www.groupstudy.com/list/CCIELab.html
>
This archive was generated by hypermail 2.1.4 : Fri Dec 12 2003 - 12:29:15 GMT-3