From: P729 (p729@xxxxxxx)
Date: Fri Jun 21 2002 - 19:36:29 GMT-3
Every baud mismatch I've encountered causes garbage to appear on the screen,
not "nothing." What makes this situation any different?
Regards,
Mas Kato
https://ecardfile.com/id/mkato
----- Original Message -----
From: "David L Stewart" <D.Stewart@mail.UTexas.edu>
To: <ccielab@groupstudy.com>
Sent: Friday, June 21, 2002 2:20 PM
Subject: RE: Please re- read a see can you help (More exact problem)
> Hyperterminal basically sucks. The BREAK doesn't work unless you
> upgrade to Hyperterminal PE. And, to change the baud rate, you
> cannot simply change it and continue using it. To be positive, you
> must change the baud rate, save the settings, close hyperterminal,
> then reopen hyperterminal with the saved .ht file. This is a big
> pain, so if you do this much, you need to make a 1200.ht, 2400.ht
> 4800.ht, 9600.ht 19200.ht and 38400.ht. This way you really know
> you are at that particular baud rate.
>
> At 02:13 PM 6/21/2002, carl.newman@elynxtech.com wrote:
> >Just an Idea,
> >
> >You may have to change the default speed of the HyperTerminal to some
thing
> >other than 9600. I remember the register changing with the default
console
> >port change baud rate if you change it in confreg. A register guide is
in
> >the front of the Solie book. I would pick a few speeds and test.
> >
> >
> >Carl
> >
> >-----Original Message-----
> >From: P729 [mailto:p729@cox.net]
> >Sent: Friday, June 21, 2002 1:43 PM
> >To: Casey, Paul (6822); 'CCIE-Groupstudy'
> >Subject: Re: Please re- read a see can you help (More exact problem)
> >
> >Too bad the archive search is still broken. I seem to recall a service of
> >some type that made it harder to break into the 26/3600 series routers.
> >Although the name of the service made it sound like it would be
impossible
> >to break into rommon, someone wrote in that there is actually a small
window
> >of opportunity to break in and set the config register with no echo and
then
> >reboot. My CCO searches are coming up empty, so it may have been in an
> >special ISP train.
> >
> >Can you post the output of 'show ver' ?
> >
> >Regards,
> >
> >Mas Kato
> >https://ecardfile.com/id/mkato
> >----- Original Message -----
> >From: "Casey, Paul (6822)" <Paul.Casey@o2.com>
> >To: "'CCIE-Groupstudy'" <ccielab@groupstudy.com>
> >Cc: "'Hyunseog Ryu'" <moonhunt@firewall.moonworld.org>; "'Bauer, Rick'"
> ><BAUERR@toysrus.com>
> >Sent: Friday, June 21, 2002 10:25 AM
> >Subject: Please re- read a see can you help (More exact problem)
> >
> >
> > > Password recovery page doesnt doesnt help
> > >
> > > You dont see anything with console access in Hyperterminal...
> > >
> > > Here my serious problem
> > >
> > > I have a router and I dont know the enable password for it, 12-14
months
> >old
> > > and no one can remember the password.
> > > Thats not the worst
> > > I can get into user mode and when I type show version the confreg
register
> > > is set to 0x1202 ... (seemed a bit funny)
> > >
> > > Now when the router boots and I connect to the console port you cant
see
> > > anything happening on the console port, therefore I cant get into
romon
> > > mode Pressing keys has not effect, You just cant see anything or do
> > > anything
> > >
> > > This confreg-reg setting must have done something serious.
> > >
> > > However, after several minutes when I connect to the aux port I get
> >"press
> > > any key to continue" appears on hyper
> > > terminal screen and I am back in user mode again.
> > > Aux mode only becomes active after bootup,
> > >
> > > image is still booting so thats ok, but back in user access, without
> > > password.
> > > and cant get to console because of the confreg-reg setting ..... and
cant
> > > change confreg-reg from user mode..
> > >
> > >
> > > I need to get access to this router ASAP and get access to romon fix
the
> > > password problem.
> > >
> > > it is a 2600 series router .....
> > > Also when I check the interfaces for user mode, they are all
> > > administratively shut down... so thats no help...
> > >
> > > I seemed to be locked out of the router, except for user mode which
seems
> >to
> > > be good for nothing.
> > > A bit of a catch 22 situation.
> > >
> > >
> > > Any help appreciated.,..
> > >
> > >
> > >
>
>***************************************************************************
*
> >************
> > >
> > > This E-mail is from O2. The E-mail and any files
> > > transmitted with it are confidential and may also be privileged and
> >intended
> > > solely for the use of the individual or entity to whom they are
addressed.
> > > Any unauthorised direct or indirect dissemination, distribution or
copying
> > > of this message and any attachments is strictly prohibited. If you
have
> > > received the E-mail in error please notify postmaster@O2.com or
> > > telephone ++ 353 1 6095000.
> > >
> > >
>
>***************************************************************************
*
> >*************
This archive was generated by hypermail 2.1.4 : Tue Jul 02 2002 - 08:12:39 GMT-3