From: Louis Young (tonyblair@xxxxxxxxx)
Date: Mon Mar 25 2002 - 08:21:09 GMT-3
sorry everyone, it is my fault having not clarified this issue.
just look at the router mode after I issue the command"router ospf xx" and "rou
ter isis"
It didn't change, right?
Was it normal ????
I don't think so .
----- Original Message -----
From: "Nelson Salvatorelli" <nsalvato@cisco.com>
To: "Louis Young" <tonyblair@etang.com>
Cc: <ccielab@groupstudy.com>
Sent: Monday, March 25, 2002 6:57 PM
Subject: RE: Weird Symptom: can not enter (config-router)# mode in ISIS and OSP
F ,why???
> Sorry Louis,
>
> I don't get your issue... Could you explain more about what do you
> require?
>
> It is very confusing reading that your issue is not related to OSPF, but
> then, you want to know why you can't go into config-router submenu for
> OPSF?
>
> Clarify please!
>
> Thanks,
>
> -nelson
>
>
> > -----Original Message-----
> > From: Louis Young [mailto:tonyblair@etang.com]
> > Sent: 25 March 2002 10:42
> > To: Nelson Salvatorelli
> > Subject: Re: Weird Symptom: can not enter (config-router)#
> > mode in ISIS and OSPF ,why???
> >
> >
> > Thank you all,My issue here is not ospf related.
> > The thing I would like to know is why can't I enter routing
> > protocol config mode.
> >
> > Thanks for your patience.:)
> > ----- Original Message -----
> > From: "Nelson Salvatorelli" <nsalvato@cisco.com>
> > To: "Louis Young" <tonyblair@etang.com>
> > Sent: Monday, March 25, 2002 6:41 PM
> > Subject: RE: Weird Symptom: can not enter (config-router)#
> > mode in ISIS and OSPF ,why???
> >
> >
> > Because if you don't have an Interface with an IP address
> > configured and It's up/up, OSPF can't select a Router ID.
> >
> > Configure a Loopback interface, put an ip address on it and
> > problem should be solved.
> >
> > -nelson
> >
> >
> > > -----Original Message-----
> > > From: Louis Young [mailto:tonyblair@etang.com]
> > > Sent: 25 March 2002 10:30
> > > To: Nelson Salvatorelli; ccielab@groupstudy.com
> > > Subject: Re: Weird Symptom: can not enter (config-router)#
> > > mode in ISIS and OSPF ,why???
> > >
> > >
> > > I know that ,so ospf up or not is not an issue here, what I
> > > mean is why can't I enter routing protocol config mode???
> > > ----- Original Message -----
> > > From: "Nelson Salvatorelli" <nsalvato@cisco.com>
> > > To: "Louis Young" <tonyblair@etang.com>; <ccielab@groupstudy.com>
> > > Sent: Monday, March 25, 2002 6:12 PM
> > > Subject: RE: Weird Symptom: can not enter (config-router)#
> > > mode in ISIS and OSPF ,why???
> > >
> > >
> > > > You can't configure OSPF without having an "IP configured"
> > > interface
> > > > and the interface should be up/up...
> > > >
> > > > Off topic, this happens also in MPLS scenarios where you
> > don't have
> > > > configured an interface with the 'ip vrf forwarding <vrf_name>'
> > > >
> > > > Hope it helps!
> > > >
> > > > Cheers,
> > > >
> > > > -nelson
> > > >
> > > >
> > > > > -----Original Message-----
> > > > > From: Louis Young [mailto:tonyblair@etang.com]
> > > > > Sent: 25 March 2002 09:38
> > > > > To: ccielab@groupstudy.com
> > > > > Subject: Weird Symptom: can not enter (config-router)# mode
> > > > > in ISIS and OSPF ,why???
> > > > >
> > > > >
> > > > > Dear all,
> > > > > I got the following phenomena during lab
> > routers, it is a
> > > > > 2610,pls help me out!
> > > > >
> > > > > Router(config)#
> > > > > Router(config)#router ospf 10
> > > > > Router(config)#
> > > > > 00:18:17: %OSPF-4-NORTRID: OSPF process 10 cannot start. There
> > > > > must be at least one "up" IP interface, for OSPF to use
> > as router
> > > > > ID Router(config)#router isis Router(config)#net
> > > > > 01.2222.2222.2222.00
> > > > > ^
> > > > > % Invalid input detected at '^' marker.
> > > > >
> > > > > Router(config)#^Z
> > > > > Router#sh ver
> > > > > 00:18:54: %SYS-5-CONFIG_I: Configured from console by console
> > > > > Cisco Internetwork Operating System Software IOS (tm) C2600
> > > > > Software (C2600-IS-M), Version 12.1(10), RELEASE SOFTWARE (fc1)
> > > > > Copyright (c) 1986-2001 by cisco Systems, Inc. Compiled Mon
> > > > > 06-Aug-01 23:48 by kellythw Image
> > > > > text-base: 0x80008088, data-base: 0x80CD6E7C
> > > > >
> > > > > ROM: System Bootstrap, Version 11.3(2)XA4, RELEASE
> > SOFTWARE (fc1)
> > > > >
> > > > > Router uptime is 18 minutes
> > > > > System returned to ROM by reload
> > > > > System image file is "flash:c2600-is-mz.121-10.bin"
> > > > >
> > > > > cisco 2610 (MPC860) processor (revision 0x203) with
> > 26624K/6144K
> > > > > bytes of memory. Processor board ID JAD05270J95
> > > > > (1358695238) M860 processor: part number 0, mask 49 Bridging
> > > > > software. X.25 software, Version 3.0.0. 1 Ethernet/IEEE 802.3
> > > > > interface(s) 1 Serial network interface(s) 32K bytes of
> > > > > non-volatile configuration memory. 8192K bytes of processor
> > > > > board System flash (Read/Write)
> > > > >
> > > > > Configuration register is 0x2102
> > > > >
> > > > >
> > > > > Thanks in advance.
> > > > >
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:57:21 GMT-3