From: Clifton Stewart (cliftonlstewart@xxxxxxxx)
Date: Thu Jan 03 2002 - 01:44:44 GMT-3
Zakir,
One of your problems in your dialer-map statement. The phone number should be
listed in the broadcast statment, for the side that will do the dialing. You ha
ve
the suffix, but are missing the beginning four numbers of the LDN. Change those
statements and let us know how it goes.
-Cliff
Zakir A wrote:
> I have a very similar basic config, but can never get the line up.
>
> ISDN_R2#sh deb
> PPP:
> PPP authentication debugging is on
> PPP protocol negotiation debugging is on
> ISDN:
> ISDN events debugging is on
> Dial on demand:
> Dial on demand events debugging is on
>
> ISDN_R2#ping 10.1.1.1
>
> Type escape sequence to abort.
> Sending 5, 100-byte ICMP Echos to 10.1.1.1, timeout is 2 seconds:
>
> BRI0: Dialing cause ip (s=10.1.1.2, d=10.1.1.1)
> BRI0: Attempting to dial 1111
> ISDN BR0: Event: Call to 1111 at 64 Kb/s
> ISDN BR0: Activating...
> %ISDN-6-LAYER2DOWN: Layer 2 for Interface BRI0, TEI 255 changed to down
> ISDN BR0: received HOST_DISCONNECT_ACK
> BRI0: wait for carrier timeout, call id=0x8005.
> BRI0: Dialing cause ip (s=10.1.1.2, d=10.1.1.1)
> BRI0: Attempting to dial 1111
> ISDN BR0: Event: Call to 1111 at 64 Kb/s
> ISDN BR0: Activating
> BRI0: wait for carrier timeout, call id=0x8006
> ISDN BR0: Physical layer is IF_DOWN
> ISDN BR0: Shutting down ME
> ISDN BR0: Shutting down ISDN Layer 3.
> Success rate is 0 percent (0/5)
> ISDN_R2#
>
> sh run
> Building configuration...
>
> Current configuration:
> !
> version 11.2
> no service udp-small-servers
> no service tcp-small-servers
> !
> hostname ISDN_R2
> !
> !
> username ISDN_R2 password 0 cisco123
> username ISDN_R1 password 0 cisco123
> partition flash 2 8 8
> !
> isdn switch-type basic-net3
> !
> interface Serial0
> no ip address
> shutdown
> no fair-queue
> !
> interface Serial1
> no ip address
> shutdown
> !
> interface TokenRing0
> no ip address
> shutdown
> !
> interface BRI0
> ip address 10.1.1.2 255.255.255.0
> encapsulation ppp
> dialer map ip 10.1.1.1 name ISDN_R1 broadcast 1111
> dialer-group 1
> ppp authentication chap
> !
> no ip classless
> access-list 101 permit ip any any
> dialer-list 1 protocol ip list 101
> !
> line con 0
> line aux 0
> line vty 0 4
> login
> !
> end
> ----- Original Message -----
> From: paul jin
> To: Zakir A ; ccielab@groupstudy.com
> Sent: Wednesday, January 02, 2002 8:12 PM
> Subject: Re: TROUBLES-- ISDN simulator from marc russell
>
> Hi,
> I guess you are talking about the slimline?
> Out of the box, the dial number for port 1 is 1111 and port 2 is 2222. bot
h
> channels use the same
> number for each port. And switch type is basic-net3.
>
> The only thing that I have changed on the sim is the default number of 1111
> to 5551111 and from 2222 to 5552222.
> Hope this helps.
>
> Here is the base config I used to test out the new phone numbers...
>
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:56:14 GMT-3