From: Tariq Sharif (tariq_sharif@xxxxxxxxxxxxxx)
Date: Tue May 08 2001 - 08:20:43 GMT-3
Hi Richard
Many thanks & regards.
Tariq Sharif
-----Original Message-----
From: Richard Gallagher [mailto:rgallagh@cisco.com]
Sent: 08 May 2001 12:18
To: Tariq Sharif
Subject: Re: Custom Queuing Scenario
Hi Tariq,
That is 100% correct, when it spcifies badwidth this is a little misleading
I
think. Just think of it in 1500 bytes chunks - this is the easiest way!!
This is applicable for any circuit!
Rich
On May 8, 12:13pm, Tariq Sharif chatted about:
> Subject:RE: Custom Queuing Scenario
> Richard
>
> So the implied total bandwidth is 6000 bytes (since 3 queues & 1 Queue has
> been assigned higher bandwidth). Half goes to Q1 & the other 1/2 is
divided
> equally between the other 2 Qs. I know this is different way of looking at
> it but this is this correct?
>
> I take it this is applicable for any circuit?
>
> Many thanks & regards.
>
> Tariq Sharif
>
>
>
> -----Original Message-----
> From: Richard Gallagher [mailto:rgallagh@cisco.com]
> Sent: 08 May 2001 11:53
> To: Tariq Sharif; Ccielab@Groupstudy. Com
> Subject: Re: Custom Queuing Scenario
>
>
> Tariq,
>
> - Default bandwidth is 1500 bytes
>
> So the follow applies:
>
> - Queue 1 has 3000 bytes - 50%
> - Queue 2 has 1500 bytes (default) - 25%
> - Queue 2 uses access list 900 to clasify traffic - IPX/NCP
> - Queue 4 default has 1500 (defualt)- 25%
>
> Rich
> CCIE #7211
>
> On May 8, 11:40am, Tariq Sharif chatted about:
> > Subject:Custom Queuing Scenario
> > I'm looking at Caslow 1st edi page 735 Custom Queuing Scenario. I see
how
> > 50% bandwidth is allocated to DLSw+ but I do not follow how the example
> > queue will allocate 25% bandwidth to IPX/NCP. Can someone pls shed some
> > light on this. Will this example apply to any serial link (e.g. Frame)
> with
> > any bandwidth circuit?
> >
> >
> > Many thanks & regards.
> >
> > Tariq Sharif
> >
> > [GroupStudy.com removed an attachment of type application/ms-tnef which
> had a
> name of winmail.dat]
> > **Please read:http://www.groupstudy.com/list/posting.html
> >-- End of waffle from Tariq Sharif
>
>
>-- End of waffle from Tariq Sharif
--*** Please copy your emails to attach@cisco.com *** #----------------------------------------------------------------------# # || || | Richard Gallagher | Direct: +32 2 704 5421 # # || || | CCIE #7211 | Fax: +32 2 704 6000 # # |||| |||| | Cisco Systems Belgium | email:rgallagh@cisco.com # #.:||||||:.:||||||:.| Euro CATS Team | http://www.cisco.com/tac # #----------------------------------------------------------------------# Check out this link: http://www.cisco.com/warp/customer/63/ **Please read:http://www.groupstudy.com/list/posting.html
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:30:36 GMT-3