From: Andres Zeller (azeller@xxxxxxxxxx)
Date: Sat Apr 07 2001 - 16:59:31 GMT-3
I think what you are enabling with the command:
ip rcmd remote-host admin1 222.222.222.222 wg1r1 enable
is allow user admin1 from the host address 222.222.222.222. and you then specif
y user admin1 when
you execute the command. You definitely do not have to have the username of you
r remote user
specified anywhere except in your
rcmd remote-host .... statement
and it will still work.
Andres
Tariq Sharif wrote:
> Has anyone played with RSH command. some text say that you need to have
> "username admin1..." on the RSH server router but I've got it working
> without that (see config below). Any ideas?
>
> Many thanks & regards.
> Tariq Sharif
>
> RSH Server Router:
>
> hostname wg1r2
> !
> ip rcmd rsh-enable
> ip rcmd remote-host admin1 222.222.222.222 wg1r1 enable
> !
> end
>
> RSH test Client:
>
> hostname wg1r1
> !
> ip rcmd source-interface Loopback300
> !
> interface Loopback300
> ip address 222.222.222.222 255.255.255.0
> !
> end
>
> wg1r1#rsh 140.1.11.5 /user admin1 sho int loop1
>
> Loopback1 is up, line protocol is up
> Hardware is Loopback
> MTU 1514 bytes, BW 8000000 Kbit, DLY 5000 usec,
> reliability 255/255, txload 1/255, rxload 1/255
> Encapsulation LOOPBACK, loopback not set
> Last input never, output never, output hang never
> Last clearing of "show interface" counters never
> Queueing strategy: fifo
> Output queue 0/0, 0 drops; input queue 0/75, 0 drops
> 5 minute input rate 0 bits/sec, 0 packets/sec
> wg1r1#
>
> [demime 0.98b removed an attachment of type application/ms-tnef which had a n
ame of winmail.dat]
> **NOTE** All LAB SWAP messages should now be sent to the
> LAB SWAP Message board on groupstudy.com.
Tariq Sharif wrote:
> Has anyone played with RSH command. some text say that you need to have
> "username admin1..." on the RSH server router but I've got it working
> without that (see config below). Any ideas?
>
> Many thanks & regards.
> Tariq Sharif
>
> RSH Server Router:
>
> hostname wg1r2
> !
> ip rcmd rsh-enable
> ip rcmd remote-host admin1 222.222.222.222 wg1r1 enable
> !
> end
>
> RSH test Client:
>
> hostname wg1r1
> !
> ip rcmd source-interface Loopback300
> !
> interface Loopback300
> ip address 222.222.222.222 255.255.255.0
> !
> end
>
> wg1r1#rsh 140.1.11.5 /user admin1 sho int loop1
>
> Loopback1 is up, line protocol is up
> Hardware is Loopback
> MTU 1514 bytes, BW 8000000 Kbit, DLY 5000 usec,
> reliability 255/255, txload 1/255, rxload 1/255
> Encapsulation LOOPBACK, loopback not set
> Last input never, output never, output hang never
> Last clearing of "show interface" counters never
> Queueing strategy: fifo
> Output queue 0/0, 0 drops; input queue 0/75, 0 drops
> 5 minute input rate 0 bits/sec, 0 packets/sec
> wg1r1#
>
> [demime 0.98b removed an attachment of type application/ms-tnef which had a n
ame of winmail.dat]
> **NOTE** All LAB SWAP messages should now be sent to the
> LAB SWAP Message board on groupstudy.com.
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:29:42 GMT-3