From: fwells12 (fwells12@xxxxxxxxxxx)
Date: Tue Jan 23 2001 - 01:09:23 GMT-3
My apologies. I will pay more attention to the mail client I am posting
from. Thanks for letting me know. I don't have any problems reading my own
messages :-)
----- Original Message -----
From: Chuck Larrieu <chuck@cl.cncdsl.com>
To: frank wells <fwells12@hotmail.com>
Sent: Monday, January 22, 2001 6:36 PM
Subject: RE: OSPF Problem
> Frank, might you possible use text only when posting? I find your
> presentations well worth reading, but it is difficult to sort through the
> stripped HTML
>
> Thanks.
>
> Chuck
>
> -----Original Message-----
> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
> frank wells
> Sent: Monday, January 22, 2001 1:41 PM
> To: ccielab@groupstudy.com
> Subject: Re: OSPF Problem
>
> <html><DIV>
> <P>The neighbors are formed using the RID's (router id's) this will be the
> highest loopback interface if there is one and the highest physical
> interface ip address otherwise. I suspect the link ip address and
the
> address in the neighbor statement are not the same. </P>
> <P>Trace an address on the other side of the frame and see what your first
> hop is. That is probably the ip address of the far side of the
> link.</P>
> <P><BR><BR> </P></DIV>
> <DIV></DIV>
> <DIV></DIV>>From: "Moran, Ed" <MORANE@TELECOMSYS.COM>
> <DIV></DIV>>Reply-To: "Moran, Ed" <MORANE@TELECOMSYS.COM>
> <DIV></DIV>>To: "'ccielab@groupstudy.com'" <CCIELAB@GROUPSTUDY.COM>
> <DIV></DIV>>Subject: OSPF Problem
> <DIV></DIV>>Date: Mon, 22 Jan 2001 16:06:31 -0500
> <DIV></DIV>>
> <DIV></DIV>>I have OSPF configured over Frame Relay. I am using
> point-to-multipoint
> <DIV></DIV>>explicitly. The neighbors are FULL, but I cannot ping
between
> them. Any
> <DIV></DIV>>ideas?
> <DIV></DIV>>
> <DIV></DIV>>R5#sh ip ospf nei
> <DIV></DIV>>
> <DIV></DIV>>Neighbor ID Pri State Dead Time Address Interface
> <DIV></DIV>>138.1.3.3 1 FULL/ - 00:00:35 138.1.11.3 Serial0
> <DIV></DIV>>R5#ping 138.1.3.3
> <DIV></DIV>>
> <DIV></DIV>>Type escape sequence to abort.
> <DIV></DIV>>Sending 5, 100-byte ICMP Echos to 138.1.3.3, timeout is 2
> seconds:
> <DIV></DIV>>.....
> <DIV></DIV>>Success rate is 0 percent (0/5
> <DIV></DIV>>
> <DIV></DIV>>E A Moran
> <DIV></DIV>>Sr.Network Engineer/Project Manager
> <DIV></DIV>>CNE,MCSE,CCNP,CCDP
> <DIV></DIV>>TeleCommunication Systems
> <DIV></DIV>>813-831-6353
> <DIV></DIV>>
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:27:40 GMT-3