From: Kevin Baumgartner (kbaumgar@xxxxxxxxx)
Date: Mon Aug 28 2000 - 18:16:10 GMT-3
Should be the Tokenring interface or the ethernet since the end stations
are on either Tokenring or ethernet.
- Kevin
At 01:43 PM 8/28/00 -0700, you wrote:
>Does anyone know why the remote peer address can't be the bri interface?
>Meaning if I set my remote-peer statements to the bri interfaces on each
>side I loose my circuits. Although I can ping both sides no capabilities
>exchanges occur. My initial thought is because of the icanreach
>mac-address which points to the token-ring interfaces. Is this the best
>method to use when implementing DDR with DLSw+? Thanks.
>
>
>Clifton Stewart-CCNA, CCIE Candidate
>
>
>=====================
>CONFIGS
>=====================
>
>Current configuration:
>!
>version 11.2
>no service password-encryption
>no service udp-small-servers
>no service tcp-small-servers
>!
>hostname R2504a
>!
>!
>username R2504b password 0 cisco
>ip subnet-zero
>no ip domain-lookup
>isdn switch-type basic-ni1
>source-bridge ring-group 99
>dlsw local-peer peer-id 10.11.1.4 promiscuous
>dlsw remote-peer 0 tcp 10.11.1.5 keepalive 0 timeout 90<---Would peer to
>10.11.6.2
>dlsw icanreach mac-address 0007.789d.ec82 mask 0000.0000.0000
>dlsw prom-peer-defaults cost 2
>!
>interface Serial0
> no ip address
> shutdown
>!
>interface Serial1
> no ip address
> shutdown
>!
>interface TokenRing0
> ip address 10.11.1.4 255.255.255.0
> ring-speed 16
> source-bridge 25 1 99
> source-bridge spanning
>!
>interface BRI0
> ip address 10.11.6.1 255.255.255.0
> encapsulation ppp
> isdn spid1 0835866101 8358661
> isdn spid2 0835866301 8358663
> dialer map llc2 name R2504b broadcast 8358662
> dialer map ip 10.11.6.2 name R2504b broadcast 8358662
> dialer hold-queue 75
> dialer-group 1
> ppp authentication chap
>!
>router ospf 1
> network 0.0.0.0 255.255.255.255 area 0
>!
>no ip classless
>ip route 0.0.0.0 0.0.0.0 10.11.1.5
>ip route 10.11.6.0 255.255.255.0 10.11.6.2
>!
>dialer-list 1 protocol ip list 103
>!
>line con 0
>line aux 0
>line vty 0 4
> no exec
> login
>!
>end
>
>R2504a#
>
>==========================================>
>Current configuration:
>!
>version 12.0
>service timestamps debug uptime
>service timestamps log uptime
>no service password-encryption
>!
>hostname R2504b
>!
>!
>username R2504a password 0 cisco
>ip subnet-zero
>no ip domain-lookup
>isdn switch-type basic-ni
>!
>source-bridge ring-group 99
>dlsw local-peer peer-id 10.11.1.5 promiscuous
>dlsw remote-peer 0 tcp 10.11.1.4 keepalive 0 timeout 90<--- Would peer
>to 10.11.6.1
>!
>!
>interface Serial0
> no ip address
> no ip directed-broadcast
> no ip mroute-cache
> shutdown
> no fair-queue
>!
>interface Serial1
> no ip address
> no ip directed-broadcast
> shutdown
>!
>interface TokenRing0
> ip address 10.11.1.5 255.255.255.0
> no ip directed-broadcast
> ip ospf interface-retry 0
> ring-speed 16
> source-bridge 25 1 99
> source-bridge spanning
>!
>interface BRI0
> ip address 10.11.6.2 255.255.255.0
> no ip directed-broadcast
> encapsulation ppp
> ip ospf interface-retry 0
> dialer map llc2 name R2504a broadcast
> dialer map ip 10.11.6.1 name R2504a broadcast
> dialer hold-queue 75
> dialer-group 1
> isdn switch-type basic-ni
> isdn spid1 0835866201 8358662
> isdn spid2 0835866401 8358664
> ppp authentication chap
>!
>router ospf 1
> network 0.0.0.0 255.255.255.255 area 0
>!
>ip classless
>ip route 0.0.0.0 0.0.0.0 10.11.1.4
>ip route 10.11.1.0 255.255.255.0 10.11.6.1
>!
>dialer-list 1 protocol ip list 103
>!
>!
>line con 0
> transport input none
>line aux 0
>line vty 0 4
> no exec
> login
>!
>end
>
>R2504b#
>
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 08:24:31 GMT-3