From: Kevin Baumgartner (kbaumgar@xxxxxxxxx)
Date: Mon Aug 28 2000 - 21:08:05 GMT-3
Good question I have not idea why Clifton is doing this if he just
doing DSLW.
Kevin
At 10:34 AM 8/29/00 +1100, you wrote:
>Hello.
>
>Why do you need to map the LLC2 stuff? I understand with Frame direct encap
>you need to either 'pass-thru' or map the LLC2, but why with IP over ISDN do
>you need to?
>
>
>Simon
>-----Original Message-----
>From: Clifton Stewart [mailto:cliftonlstewart@home.com]
>Sent: Tuesday, August 29, 2000 7:28 AM
>To: Kevin Baumgartner; ccielab@groupstudy.com
>Subject: DLSw+ over ISDN
>
>
>Thanks Kevin. Logically I was thinking that but couldn't find any
>documentation to back it up. For people that want to implement this
>config on etherent make the interface part of the bridge-group and
>specify the dlsw brige-group with the corresponding number.
>
>-Cliff
>
>Kevin Baumgartner wrote:
> >
> > Should be the Tokenring interface or the ethernet since the end stations
> > are on either Tokenring or ethernet.
> >
> > - Kevin
> >
> > At 01:43 PM 8/28/00 -0700, you wrote:
> > >Does anyone know why the remote peer address can't be the bri interface?
> > >Meaning if I set my remote-peer statements to the bri interfaces on each
> > >side I loose my circuits. Although I can ping both sides no capabilities
> > >exchanges occur. My initial thought is because of the icanreach
> > >mac-address which points to the token-ring interfaces. Is this the best
> > >method to use when implementing DDR with DLSw+? Thanks.
> > >
> > >
> > >Clifton Stewart-CCNA, CCIE Candidate
> > >
> > >
> > >=====================
> > >CONFIGS
> > >=====================
> > >
> > >Current configuration:
> > >!
> > >version 11.2
> > >no service password-encryption
> > >no service udp-small-servers
> > >no service tcp-small-servers
> > >!
> > >hostname R2504a
> > >!
> > >!
> > >username R2504b password 0 cisco
> > >ip subnet-zero
> > >no ip domain-lookup
> > >isdn switch-type basic-ni1
> > >source-bridge ring-group 99
> > >dlsw local-peer peer-id 10.11.1.4 promiscuous
> > >dlsw remote-peer 0 tcp 10.11.1.5 keepalive 0 timeout 90<---Would peer to
> > >10.11.6.2
> > >dlsw icanreach mac-address 0007.789d.ec82 mask 0000.0000.0000
> > >dlsw prom-peer-defaults cost 2
> > >!
> > >interface Serial0
> > > no ip address
> > > shutdown
> > >!
> > >interface Serial1
> > > no ip address
> > > shutdown
> > >!
> > >interface TokenRing0
> > > ip address 10.11.1.4 255.255.255.0
> > > ring-speed 16
> > > source-bridge 25 1 99
> > > source-bridge spanning
> > >!
> > >interface BRI0
> > > ip address 10.11.6.1 255.255.255.0
> > > encapsulation ppp
> > > isdn spid1 0835866101 8358661
> > > isdn spid2 0835866301 8358663
> > > dialer map llc2 name R2504b broadcast 8358662
> > > dialer map ip 10.11.6.2 name R2504b broadcast 8358662
> > > dialer hold-queue 75
> > > dialer-group 1
> > > ppp authentication chap
> > >!
> > >router ospf 1
> > > network 0.0.0.0 255.255.255.255 area 0
> > >!
> > >no ip classless
> > >ip route 0.0.0.0 0.0.0.0 10.11.1.5
> > >ip route 10.11.6.0 255.255.255.0 10.11.6.2
> > >!
> > >dialer-list 1 protocol ip list 103
> > >!
> > >line con 0
> > >line aux 0
> > >line vty 0 4
> > > no exec
> > > login
> > >!
> > >end
> > >
> > >R2504a#
> > >
> > >==========================================>
> > >Current configuration:
> > >!
> > >version 12.0
> > >service timestamps debug uptime
> > >service timestamps log uptime
> > >no service password-encryption
> > >!
> > >hostname R2504b
> > >!
> > >!
> > >username R2504a password 0 cisco
> > >ip subnet-zero
> > >no ip domain-lookup
> > >isdn switch-type basic-ni
> > >!
> > >source-bridge ring-group 99
> > >dlsw local-peer peer-id 10.11.1.5 promiscuous
> > >dlsw remote-peer 0 tcp 10.11.1.4 keepalive 0 timeout 90<--- Would peer
> > >to 10.11.6.1
> > >!
> > >!
> > >interface Serial0
> > > no ip address
> > > no ip directed-broadcast
> > > no ip mroute-cache
> > > shutdown
> > > no fair-queue
> > >!
> > >interface Serial1
> > > no ip address
> > > no ip directed-broadcast
> > > shutdown
> > >!
> > >interface TokenRing0
> > > ip address 10.11.1.5 255.255.255.0
> > > no ip directed-broadcast
> > > ip ospf interface-retry 0
> > > ring-speed 16
> > > source-bridge 25 1 99
> > > source-bridge spanning
> > >!
> > >interface BRI0
> > > ip address 10.11.6.2 255.255.255.0
> > > no ip directed-broadcast
> > > encapsulation ppp
> > > ip ospf interface-retry 0
> > > dialer map llc2 name R2504a broadcast
> > > dialer map ip 10.11.6.1 name R2504a broadcast
> > > dialer hold-queue 75
> > > dialer-group 1
> > > isdn switch-type basic-ni
> > > isdn spid1 0835866201 8358662
> > > isdn spid2 0835866401 8358664
> > > ppp authentication chap
> > >!
> > >router ospf 1
> > > network 0.0.0.0 255.255.255.255 area 0
> > >!
> > >ip classless
> > >ip route 0.0.0.0 0.0.0.0 10.11.1.4
> > >ip route 10.11.1.0 255.255.255.0 10.11.6.1
> > >!
> > >dialer-list 1 protocol ip list 103
> > >!
> > >!
> > >line con 0
> > > transport input none
> > >line aux 0
> > >line vty 0 4
> > > no exec
> > > login
> > >!
> > >end
> > >
> > >R2504b#
> > >
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 08:24:31 GMT-3