From: Clifton Stewart (cliftonlstewart@xxxxxxxx)
Date: Mon Aug 28 2000 - 18:27:34 GMT-3
Thanks Kevin. Logically I was thinking that but couldn't find any
documentation to back it up. For people that want to implement this
config on etherent make the interface part of the bridge-group and
specify the dlsw brige-group with the corresponding number.
-Cliff
Kevin Baumgartner wrote:
>
> Should be the Tokenring interface or the ethernet since the end stations
> are on either Tokenring or ethernet.
>
> - Kevin
>
> At 01:43 PM 8/28/00 -0700, you wrote:
> >Does anyone know why the remote peer address can't be the bri interface?
> >Meaning if I set my remote-peer statements to the bri interfaces on each
> >side I loose my circuits. Although I can ping both sides no capabilities
> >exchanges occur. My initial thought is because of the icanreach
> >mac-address which points to the token-ring interfaces. Is this the best
> >method to use when implementing DDR with DLSw+? Thanks.
> >
> >
> >Clifton Stewart-CCNA, CCIE Candidate
> >
> >
> >=====================
> >CONFIGS
> >=====================
> >
> >Current configuration:
> >!
> >version 11.2
> >no service password-encryption
> >no service udp-small-servers
> >no service tcp-small-servers
> >!
> >hostname R2504a
> >!
> >!
> >username R2504b password 0 cisco
> >ip subnet-zero
> >no ip domain-lookup
> >isdn switch-type basic-ni1
> >source-bridge ring-group 99
> >dlsw local-peer peer-id 10.11.1.4 promiscuous
> >dlsw remote-peer 0 tcp 10.11.1.5 keepalive 0 timeout 90<---Would peer to
> >10.11.6.2
> >dlsw icanreach mac-address 0007.789d.ec82 mask 0000.0000.0000
> >dlsw prom-peer-defaults cost 2
> >!
> >interface Serial0
> > no ip address
> > shutdown
> >!
> >interface Serial1
> > no ip address
> > shutdown
> >!
> >interface TokenRing0
> > ip address 10.11.1.4 255.255.255.0
> > ring-speed 16
> > source-bridge 25 1 99
> > source-bridge spanning
> >!
> >interface BRI0
> > ip address 10.11.6.1 255.255.255.0
> > encapsulation ppp
> > isdn spid1 0835866101 8358661
> > isdn spid2 0835866301 8358663
> > dialer map llc2 name R2504b broadcast 8358662
> > dialer map ip 10.11.6.2 name R2504b broadcast 8358662
> > dialer hold-queue 75
> > dialer-group 1
> > ppp authentication chap
> >!
> >router ospf 1
> > network 0.0.0.0 255.255.255.255 area 0
> >!
> >no ip classless
> >ip route 0.0.0.0 0.0.0.0 10.11.1.5
> >ip route 10.11.6.0 255.255.255.0 10.11.6.2
> >!
> >dialer-list 1 protocol ip list 103
> >!
> >line con 0
> >line aux 0
> >line vty 0 4
> > no exec
> > login
> >!
> >end
> >
> >R2504a#
> >
> >==========================================>
> >Current configuration:
> >!
> >version 12.0
> >service timestamps debug uptime
> >service timestamps log uptime
> >no service password-encryption
> >!
> >hostname R2504b
> >!
> >!
> >username R2504a password 0 cisco
> >ip subnet-zero
> >no ip domain-lookup
> >isdn switch-type basic-ni
> >!
> >source-bridge ring-group 99
> >dlsw local-peer peer-id 10.11.1.5 promiscuous
> >dlsw remote-peer 0 tcp 10.11.1.4 keepalive 0 timeout 90<--- Would peer
> >to 10.11.6.1
> >!
> >!
> >interface Serial0
> > no ip address
> > no ip directed-broadcast
> > no ip mroute-cache
> > shutdown
> > no fair-queue
> >!
> >interface Serial1
> > no ip address
> > no ip directed-broadcast
> > shutdown
> >!
> >interface TokenRing0
> > ip address 10.11.1.5 255.255.255.0
> > no ip directed-broadcast
> > ip ospf interface-retry 0
> > ring-speed 16
> > source-bridge 25 1 99
> > source-bridge spanning
> >!
> >interface BRI0
> > ip address 10.11.6.2 255.255.255.0
> > no ip directed-broadcast
> > encapsulation ppp
> > ip ospf interface-retry 0
> > dialer map llc2 name R2504a broadcast
> > dialer map ip 10.11.6.1 name R2504a broadcast
> > dialer hold-queue 75
> > dialer-group 1
> > isdn switch-type basic-ni
> > isdn spid1 0835866201 8358662
> > isdn spid2 0835866401 8358664
> > ppp authentication chap
> >!
> >router ospf 1
> > network 0.0.0.0 255.255.255.255 area 0
> >!
> >ip classless
> >ip route 0.0.0.0 0.0.0.0 10.11.1.4
> >ip route 10.11.1.0 255.255.255.0 10.11.6.1
> >!
> >dialer-list 1 protocol ip list 103
> >!
> >!
> >line con 0
> > transport input none
> >line aux 0
> >line vty 0 4
> > no exec
> > login
> >!
> >end
> >
> >R2504b#
> >
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 08:24:31 GMT-3