Re: FW: xconnect

According to
http://www.cisco.com/en/US/docs/ios/12_0s/feature/guide/fsinterw.html
IPv6 is not supported, and there are issues with IPCP
negotiation across the PW. Have you tried ipcp address proxy ?

I'll let someone who has played with this answer anyways. Just felt
guilty for my previous response.
-Carlos

Mohammad Khalil @ 09/05/2013 19:18 -0300 dixit:
> From: eng_mssk_at_hotmail.com
> To: eng_mssk_at_hotmail.com
> Subject:
> Date: Fri, 10 May 2013 01:17:53 +0300
>
>
>
>
> Hi , I am trying to configure xconnect between PPP and ethernet
>
> R12#sh run int f1/0
> interface FastEthernet1/0
> ip address 10.1.124.12 255.255.255.0
> speed 100
> duplex full
> ipv6 address 2001:10:124::12/64
>
> R6#sh run int f2/0
> interface FastEthernet2/0
> no ip address
> speed 100
> duplex full
> no keepalive
> xconnect 4.4.4.4 124 encapsulation mpls pw-class XC
>
> R14#sh run int s1/0
> interface Serial1/0
> ip address 10.1.124.14 255.255.255.0
> encapsulation ppp
> ipv6 address 2001:10:124::14/64
> clock rate 128000
>
> R4#sh run int s3/0
> interface Serial3/0
> no ip address
> encapsulation ppp
> keepalive 10 3
> clock rate 128000
> xconnect 6.6.6.6 124 encapsulation mpls pw-class XC
>
> R4#sh run | sec pse
> pseudowire-class XC
> encapsulation mpls
> interworking ip
>
> R6#sh run | sec pse
> pseudowire-class XC
> encapsulation mpls
> interworking ip
>
> R4#sh mpls ldp neighbor 6.6.6.6
> Peer LDP Ident: 6.6.6.6:0; Local LDP Ident 4.4.4.4:0
> TCP connection: 6.6.6.6.47298 - 4.4.4.4.646
> State: Oper; Msgs sent/rcvd: 21/15; Downstream
> Up time: 00:03:53
> LDP discovery sources:
> Targeted Hello 4.4.4.4 -> 6.6.6.6, active, passive
> Addresses bound to peer LDP Ident:
> 192.1.36.6 6.6.6.6 192.1.67.6
>
> R6#sh mpls ldp neighbor 4.4.4.4
> Peer LDP Ident: 4.4.4.4:0; Local LDP Ident 6.6.6.6:0
> TCP connection: 4.4.4.4.646 - 6.6.6.6.47298
> State: Oper; Msgs sent/rcvd: 15/21; Downstream
> Up time: 00:04:03
> LDP discovery sources:
> Targeted Hello 6.6.6.6 -> 4.4.4.4, active, passive
> Addresses bound to peer LDP Ident:
> 192.1.14.4 192.1.45.4 4.4.4.4 44.44.44.44
>
> R4#sh mpls l2transport summary
> Destination address: 6.6.6.6, total number of vc: 1
> 0 unknown, 0 up, 1 down, 0 admin down, 0 recovering, 0 standby, 0 hotstandby
>
> R6#sh mpls l2transport summary
> Destination address: 4.4.4.4, total number of vc: 1
> 0 unknown, 0 up, 1 down, 0 admin down, 0 recovering, 0 standby, 0 hotstandby
>
> I have tried to play with MTU but nothing changes , what i am missing?
>
>
> Blogs and organic groups at http://www.ccie.net
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
>
>
>
>
>
>

-- 
Carlos G Mendioroz  <tron_at_huapi.ba.ar>  LW7 EQI  Argentina
Blogs and organic groups at http://www.ccie.net