FW: xconnect

From: eng_mssk_at_hotmail.com
To: eng_mssk_at_hotmail.com
Subject:
Date: Fri, 10 May 2013 01:17:53 +0300

Hi , I am trying to configure xconnect between PPP and ethernet

R12#sh run int f1/0
interface FastEthernet1/0
 ip address 10.1.124.12 255.255.255.0
 speed 100
 duplex full
 ipv6 address 2001:10:124::12/64

R6#sh run int f2/0
interface FastEthernet2/0
 no ip address
 speed 100
 duplex full
 no keepalive
 xconnect 4.4.4.4 124 encapsulation mpls pw-class XC

R14#sh run int s1/0
interface Serial1/0
 ip address 10.1.124.14 255.255.255.0
 encapsulation ppp
 ipv6 address 2001:10:124::14/64
 clock rate 128000

R4#sh run int s3/0
interface Serial3/0
 no ip address
 encapsulation ppp
 keepalive 10 3
 clock rate 128000
 xconnect 6.6.6.6 124 encapsulation mpls pw-class XC

R4#sh run | sec pse
pseudowire-class XC
 encapsulation mpls
 interworking ip

R6#sh run | sec pse
pseudowire-class XC
 encapsulation mpls
 interworking ip

R4#sh mpls ldp neighbor 6.6.6.6
    Peer LDP Ident: 6.6.6.6:0; Local LDP Ident 4.4.4.4:0
        TCP connection: 6.6.6.6.47298 - 4.4.4.4.646
        State: Oper; Msgs sent/rcvd: 21/15; Downstream
        Up time: 00:03:53
        LDP discovery sources:
          Targeted Hello 4.4.4.4 -> 6.6.6.6, active, passive
        Addresses bound to peer LDP Ident:
          192.1.36.6 6.6.6.6 192.1.67.6

R6#sh mpls ldp neighbor 4.4.4.4
    Peer LDP Ident: 4.4.4.4:0; Local LDP Ident 6.6.6.6:0
        TCP connection: 4.4.4.4.646 - 6.6.6.6.47298
        State: Oper; Msgs sent/rcvd: 15/21; Downstream
        Up time: 00:04:03
        LDP discovery sources:
          Targeted Hello 6.6.6.6 -> 4.4.4.4, active, passive
        Addresses bound to peer LDP Ident:
          192.1.14.4 192.1.45.4 4.4.4.4 44.44.44.44

R4#sh mpls l2transport summary
Destination address: 6.6.6.6, total number of vc: 1
  0 unknown, 0 up, 1 down, 0 admin down, 0 recovering, 0 standby, 0 hotstandby

R6#sh mpls l2transport summary
Destination address: 4.4.4.4, total number of vc: 1
  0 unknown, 0 up, 1 down, 0 admin down, 0 recovering, 0 standby, 0 hotstandby

I have tried to play with MTU but nothing changes , what i am missing?

Blogs and organic groups at http://www.ccie.net
Received on Fri May 10 2013 - 01:18:40 ART