I'm not sure what your configs say, but Interworking between encapsulations is not supported for IPv6, even in IOS XE 3S or IOS XR 4.3. In other words if you're going between Ethernet and PPP over AToM, then only the IPv4 packet is extracted from the Attachment Circuit. All other frames are dropped.
Brian McGahan, CCIE #8593 (R&S/SP/Security), CCDE #2013::13
bmcgahan_at_INE.com
Internetwork Expert, Inc.
http://www.INE.com
-----Original Message-----
From: nobody_at_groupstudy.com [mailto:nobody_at_groupstudy.com] On Behalf Of Mohammad Khalil
Sent: Thursday, May 09, 2013 4:55 PM
To: ccielab_at_groupstudy.com
Subject: xconnect
Hi , I am trying to configure xconnect between PPP and ethernetR12#sh run int f1/0interface FastEthernet1/0 ip address 10.1.124.12 255.255.255.0 speed 100 duplex full ipv6 address 2001:10:124::12/64R6#sh run int f2/0 interface FastEthernet2/0 no ip address speed 100 duplex full no keepalive xconnect 4.4.4.4 124 encapsulation mpls pw-class XCR14#sh run int s1/0interface Serial1/0 ip address 10.1.124.14 255.255.255.0 encapsulation ppp ipv6 address 2001:10:124::14/64 clock rate 128000R4#sh run int s3/0interface Serial3/0 no ip address encapsulation ppp keepalive 10 3 clock rate 128000 xconnect 6.6.6.6 124 encapsulation mpls pw-class XCR4#sh run | sec psepseudowire-class XC encapsulation mpls interworking ipR6#sh run | sec psepseudowire-class XC encapsulation mpls interworking ipR4#sh mpls ldp neighbor 6.6.6.6 Peer LDP Ident: 6.6.6.6:0; Local LDP Ident 4.4.4.4:0 TCP connection: 6.6.6.6.47298 - 4.4.4.4.646 State: Oper; Msgs sent/rcvd: 21/15; Downstream Up !
time: 00:03:53 LDP discovery sources: Targeted Hello 4.4.4.4 -> 6.6.6.6, active, passive Addresses bound to peer LDP Ident: 192.1.36.6 6.6.6.6 192.1.67.6 R6#sh mpls ldp neighbor 4.4.4.4 Peer LDP Ident: 4.4.4.4:0; Local LDP Ident 6.6.6.6:0 TCP connection: 4.4.4.4.646 - 6.6.6.6.47298 State: Oper; Msgs sent/rcvd: 15/21; Downstream Up time: 00:04:03 LDP discovery sources: Targeted Hello 6.6.6.6 -> 4.4.4.4, active, passive Addresses bound to peer LDP Ident: 192.1.14.4 192.1.45.4 4.4.4.4 44.44.44.44 R4#sh mpls l2transport summary Destination address: 6.6.6.6, total number of vc: 1 0 unknown, 0 up, 1 down, 0 admin down, 0 recovering, 0 standby, 0 hotstandbyR6#sh mpls l2transport summary Destination address: 4.4.4.4, total number of vc: 1 0 unknown, 0 up, 1 down, 0 admin down, 0 recovering, 0 standby, 0 hotstandbyI have tried to play with MTU but nothing chan!
ges , what i am missing?
Blogs and organic groups at http://www.ccie.net
Received on Thu May 09 2013 - 20:25:34 ART
This archive was generated by hypermail 2.2.0 : Mon Jun 03 2013 - 06:34:34 ART