Multicast VPN

Hi all
I have the below topology
R1 -- R2 -- R3 -- R4 -- R5
R2 and R4 are my PE routers , I am trying to implement multicast VPN , please find below

R1#sh run int f1/0
Building configuration...

Current configuration : 114 bytes
!
interface FastEthernet1/0
 ip address 192.1.12.1 255.255.255.0
 speed 100
 duplex full
end

R1#sh run | inc ip route
ip route 0.0.0.0 0.0.0.0 192.1.12.2

R2#sh run int f1/0
Building configuration...

Current configuration : 136 bytes
!
interface FastEthernet1/0
 vrf forwarding VPN_A
 ip address 192.1.12.2 255.255.255.0
 ip pim sparse-mode
 speed 100
 duplex full
end

R2#sh run int f1/1
Building configuration...

Current configuration : 123 bytes
!
interface FastEthernet1/1
 ip address 192.1.23.2 255.255.255.0
 ip pim sparse-mode
 speed 100
 duplex full
 mpls ip
end

R2#sh run int lo0
Building configuration...

Current configuration : 83 bytes
!
interface Loopback0
 ip address 2.2.2.2 255.255.255.255
 ip pim sparse-mode
end

R2#sh run | sec router bgp
router bgp 100
 bgp log-neighbor-changes
 no bgp default ipv4-unicast
 neighbor 4.4.4.4 remote-as 100
 neighbor 4.4.4.4 update-source Loopback0
 !
 address-family ipv4
 exit-address-family
 !
 address-family vpnv4
  neighbor 4.4.4.4 activate
  neighbor 4.4.4.4 send-community both
 exit-address-family

address-family ipv4 mdt
  neighbor 4.4.4.4 activate
  neighbor 4.4.4.4 send-community both
 exit-address-family
 !
 address-family ipv4 vrf VPN_A
  network 192.1.12.0
 exit-address-family
R2#sh run | sec router ospf
router ospf 1
 router-id 2.2.2.2
 network 2.2.2.2 0.0.0.0 area 0
 network 192.1.23.2 0.0.0.0 area 0

R2#sh run | inc multi
ip multicast-routing
ip multicast-routing vrf VPN_A

R3#sh run int f1/0
Building configuration...

Current configuration : 123 bytes
!
interface FastEthernet1/0
 ip address 192.1.23.3 255.255.255.0
 ip pim sparse-mode
 speed 100
 duplex full
 mpls ip
end

R3#sh run int f1/1
Building configuration...

Current configuration : 123 bytes
!
interface FastEthernet1/1
 ip address 192.1.34.3 255.255.255.0
 ip pim sparse-mode
 speed 100
 duplex full
 mpls ip
end

R3#sh run int lo0
Building configuration...

Current configuration : 63 bytes
!
interface Loopback0
 ip address 3.3.3.3 255.255.255.255
end

R3#sh run | sec router ospf
router ospf 1
 router-id 3.3.3.3
 network 3.3.3.3 0.0.0.0 area 0
 network 192.1.23.3 0.0.0.0 area 0
 network 192.1.34.3 0.0.0.0 area 0
R3#sh run | inc multic
ip multicast-routing

R4#sh run int f1/0
Building configuration...

Current configuration : 123 bytes
!
interface FastEthernet1/0
 ip address 192.1.34.4 255.255.255.0
 ip pim sparse-mode
 speed 100
 duplex full
 mpls ip
end

R4#sh run int f1/1
Building configuration...

Current configuration : 136 bytes
!
interface FastEthernet1/1
 vrf forwarding VPN_A
 ip address 192.1.45.4 255.255.255.0
 ip pim sparse-mode
 speed 100
 duplex full
end

R4#sh run int lo0
Building configuration...

Current configuration : 113 bytes
!
interface Loopback0
 ip address 4.4.4.4 255.255.255.255
 ip pim sparse-mode
 ip igmp join-group 234.4.4.4
end

R4#sh run | sec router ospf
router ospf 1
 router-id 4.4.4.4
 network 4.4.4.4 0.0.0.0 area 0
 network 192.1.34.4 0.0.0.0 area 0
R4#sh run | sec router bgp
router bgp 100
 bgp log-neighbor-changes
 no bgp default ipv4-unicast
 neighbor 2.2.2.2 remote-as 100
 neighbor 2.2.2.2 update-source Loopback0
 !
 address-family ipv4
 exit-address-family
 !
 address-family vpnv4
  neighbor 2.2.2.2 activate
  neighbor 2.2.2.2 send-community both
 exit-address-family

address-family ipv4 mdt
  neighbor 2.2.2.2 activate
  neighbor 2.2.2.2 send-community both
 exit-address-family
 !
 address-family ipv4 vrf VPN_A
  network 192.1.45.0
 exit-address-family
R4#sh run | inc multi
ip multicast-routing
ip multicast-routing vrf VPN_A

R4#sh run | sec vrf def
vrf definition VPN_A
 rd 100:1
 route-target export 100:1
 route-target import 100:1
 !
 address-family ipv4
  mdt default 232.0.0.1
  mdt data 232.0.1.0 0.0.0.255
 exit-address-family

R5#sh run int f1/0
Building configuration...

Current configuration : 144 bytes
!
interface FastEthernet1/0
 ip address 192.1.45.5 255.255.255.0
 ip pim sparse-mode
 ip igmp join-group 235.5.5.5
 speed 100
 duplex full
end

R5#sh run | inc ip route
ip route 0.0.0.0 0.0.0.0 192.1.45.4

R1#ping 192.1.45.5 sou f1/0
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.1.45.5, timeout is 2 seconds:
Packet sent with a source address of 192.1.12.1
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 16/18/28 ms

R2#sh bgp ipv4 mdt all summary
BGP router identifier 2.2.2.2, local AS number 100
BGP table version is 3, main routing table version 3
2 network entries using 320 bytes of memory
2 path entries using 168 bytes of memory
2/2 BGP path/bestpath attribute entries using 272 bytes of memory
1 BGP extended community entries using 24 bytes of memory
0 BGP route-map cache entries using 0 bytes of memory
0 BGP filter-list cache entries using 0 bytes of memory
BGP using 784 total bytes of memory
BGP activity 4/0 prefixes, 6/2 paths, scan interval 60 secs

Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd
4.4.4.4 4 100 26 26 3 0 0 00:16:08 1
R2#sh bgp ipv4 mdt all
BGP table version is 3, local router ID is 2.2.2.2
Status codes: s suppressed, d damped, h history, * valid, > best, i - internal,
              r RIB-failure, S Stale, m multipath, b backup-path, f RT-Filter,
              x best-external, a additional-path, c RIB-compressed,
Origin codes: i - IGP, e - EGP, ? - incomplete
RPKI validation codes: V valid, I invalid, N Not found

     Network Next Hop Metric LocPrf Weight Path
Route Distinguisher: 100:1 (default for vrf VPN_A)
 *> 2.2.2.2/32 0.0.0.0 0 ?
 *>i 4.4.4.4/32 4.4.4.4 0 100 0 ?

But i am not able to ping the group joined on R5 F1/0

R1#ping 235.5.5.5 repeat 1
Type escape sequence to abort.
Sending 1, 100-byte ICMP Echos to 235.5.5.5, timeout is 2 seconds:
.

Thanks

Blogs and organic groups at http://www.ccie.net
Received on Sun Feb 10 2013 - 23:53:12 ART