RE: EIGRP over FRAME_RELAY

Each router has lo0
10.10.10.x
R2,R4,R5,R6
-----------
router eigrp 20
no auto
pass def
(R2,R5,R6) no pass s0/1/0.x where x is Router number(R4) no pass s0/0/0network 216.30.1.x 0.0.0.0
network 10.10.10.x 0.0.0.0
R2

---
int s0/1/0
no ip add
enca frame-relay
no frame inv
int s0/1/0.2 mult
no ip split-horizon eigrp 20
ip add 216.30.1.2 255.255.255.224
frame map ip 216.30.1.4 214 bro
frame map ip 216.30.1.5 215 bro
frame map ip 216.30.1.6 216 bro
frame map ip 216.30.1.2 216R4
---
int s0/0/0
enca frame
no frame inv
ip add 216.30.1.4 255.255.255.224
no ip split-horizon eigrp 20
frame map ip 216.30.1.2 412 bro
frame map ip 216.30.1.5 415 bro
frame map ip 216.30.1.6 416 bro
frame map ip 216.30.1.4 412R5
---
int s0/1/0
no ip add
enaca frame map
no frame inv
int s0/1/0.5 mult
no ip split-horizon eigrp 20
ip add 216.30.1.5 255.255.255.224
frame map ip 216.30.1.4 514 bro
frame map ip 216.30.1.2 512 bro
frame map ip 216.30.1.6 516 bro
frame map ip 216.30.1.5 512
R6
---
int s0/1/0.6
no ip add
enaca frame map
no frame inv
int s0/1/0.2 mult
no ip split-horizon eigrp 20
ip add 216.30.1.6 255.255.255.224
frame map ip 216.30.1.4 614 bro
frame map ip 216.30.1.5 615 bro
frame map ip 216.30.1.2 612 bro
frame map ip 216.30.1.6 612
 > From: joe_at_affirmedsystems.com
> To: mohd-mousa_at_hotmail.com; ccielab_at_groupstudy.com
> Subject: RE: EIGRP over FRAME_RELAY
> Date: Fri, 15 Jun 2012 17:09:11 +0000
> 
> First, don't get dinged for using too many commands - you only need no ip split-horizon on the interface with the ip... (the sub-interface for R2,R5,R6).
> 
> Split horizon won't stop them from neighboring up - just from accepting the top table it learns from that neighbor.
> 
> Post your frsw configs or if this is a dynamips backed scenario - adjust your cpu idle values - your rig might not be built out correctly to support dynamips.
> 
> >-All the frame-maps configured correctly, I have the reachablitly between all of them.
> 
> Did you remember the "BROADCAST" keyword on R4's maps?
> 
> LOL
> 
> -----Original Message-----
> From: nobody_at_groupstudy.com [mailto:nobody_at_groupstudy.com] On Behalf Of mohd-mousa_at_hotmail.com
> Sent: Friday, June 15, 2012 12:44 PM
> To: ccielab_at_groupstudy.com
> Subject: EIGRP over FRAME_RELAY
> 
> Hi Dears,
> 
> I have issue with eigrp over frame-relay, I have four router connected to each other ( full mesh )
> 
> R2-------R4
> R5-------R6
> 
> R2,R5,R6 : using the multipoint sub interfaces
> R4 : using the physical interface
> 
> -All the frame-maps configured correctly, I have the reachablitly between all of them.
> 
> -R2: all the neighbors came up
> -R5: showed the neighbors to R2,R6
> -R6: showed the neighbors to R2,R5
> 
> -R4: showed the neighbors to all of them but there was flapping to R5,R6!
> The flapping showed on R4 only,the flapped didn't appear on both R5,R6.As i know the flapped should appear on both side of the neighborship.
> ON R4 it gave me console message *RETRY LIMIT EXCEEDED*
> 
> 
> I disabled the split-horizon on R2,R4,R5,R6
> 
> R2,R5,R6 :disabled on the sub-interfaces
> R4 : disabled on the phyiscal interface.
> 
> I tried to disable the split-horizon on the phyiscal interfaces for all routers, but without any luck.
> 
> Any ideas/suggestions will highly appreciated !!
> 
> 
> Thanks in advance.
> 
> 
> Blogs and organic groups at http://www.ccie.net
> 
> _______________________________________________________________________
> Subscription information may be found at: 
> http://www.groupstudy.com/list/CCIELab.html
> 
> 
> Blogs and organic groups at http://www.ccie.net
> 
> _______________________________________________________________________
> Subscription information may be found at: 
> http://www.groupstudy.com/list/CCIELab.html
Blogs and organic groups at http://www.ccie.net