RE: PVDM2 in voice lab

Hi Guys

   Thanks your kindly support. However it sitll doesn't work after the
"test"command on my different routers. Prbably I will tried different IOS.

Thanks,
Tortle

Date: Mon, 7 Feb 2011 17:57:43 +1100
Subject: Re: PVDM2 in voice lab
From: pbhatkoti_at_gmail.com
To: matthn_at_gmail.com
CC: tron_at_huapi.ba.ar; tortletang_at_hotmail.com; sbabatunde1_at_ca.rr.com;
carl.gosselin_at_altizone.com; ccielab_at_groupstudy.com

u can test the DSP if they're good or bad using 'test' command.
or hook into a different router. could be ios that u are running is not
supporting it.

On Mon, Feb 7, 2011 at 9:38 AM, Nick Matthews <matthn_at_gmail.com> wrote:

One of those DSPs may be bad - FAIL is not a good state. You may want a TAC
case to investigate for a replacement.

-nick

On Sat, Feb 5, 2011 at 7:23 PM, Carlos G Mendioroz <tron_at_huapi.ba.ar> wrote:

> Some PVDMs are ... not that good, and they fail to start reliably.
> You can power bounce the router to see if they both come up.
> A better way is to reset them, with test reset:
>
> Router# test dsp device <slot> <id> reset
>
> <id> would be 1 for PVDM2-16, <slot> would be 1 or 2.
>
> -Carlos
>
> Tortle Tang @ 05/02/2011 18:05 -0300 dixit:
>
> Hi
>> I checked out the " show voice dsp group all" in my 2x2811 and 1x2801, the
>> second PVDM2 16 isn't up always. The PVDM2 16 card is good.
>> But whatever I tried, only PVDM2 in slot 1 can be enabled. Any idea how to
>> enable it in second slot ?
>>
>> R2#sh voice dsp group all
>> DSP groups on slot 0:
>> dsp 1:
>> State: UP, firmware: 23.8.0
>> Max signal/voice channel: 16/16
>> Max credits: 240
>> num_of_sig_chnls_allocated: 3
>> Transcoding channels allocated: 0
>> Group: FLEX_GROUP_VOICE, complexity: FLEX
>> Shared credits: 240, reserved credits: 0
>> Signaling channels allocated: 3
>> Voice channels allocated: 0
>> Credits used: 0
>> dsp 5:
>> State: FAIL, firmware: 0.0.0
>> Max signal/voice channel: 16/16
>> Max credits: 240
>> num_of_sig_chnls_allocated: 0
>> Transcoding channels allocated: 0
>> Group: FLEX_GROUP_VOICE, complexity: FLEX
>> Shared credits: 240, reserved credits: 0
>> Signaling channels allocated: 0
>> Voice channels allocated: 0
>> Credits used: 0
>>
>>
>>
>>
>>
>>
>> Thanks,
>>
>> Tortle
>>
>>
>>
>> From: matthn_at_gmail.com
>>> Date: Sat, 5 Feb 2011 10:12:45 -0500
>>> Subject: Re: PVDM2 in voice lab
>>> To: sbabatunde1_at_ca.rr.com
>>> CC: tortletang_at_hotmail.com; carl.gosselin_at_altizone.com;
>>>
>> ccielab_at_groupstudy.com
>>
>>> Check out 'show voice dsp group all'
>>>
>>> This will list the DSPs and what is being used on each. Each 16 is 1 DSP,
>>> and conferencing takes up an entire DSP whether a conference is going on
>>> or
>>> not. Like mentioned, you've likely got a T1/E1 that's eating partially
>>> through the 2nd DSP.
>>>
>>> There shouldn't be a difference between 2801/2811/2901/2911/etc.
>>>
>>> -nick
>>>
>>> On Sat, Feb 5, 2011 at 8:19 AM, Babatunde Sanda
>>>
>> <sbabatunde1_at_ca.rr.com>wrote:
>>
>>> If you already have cards like fxo and fxs installed, this cards are
>>>>
>>> given
>>
>>> priority over your farms. Remember the purpose of dscpfarms is to share
>>>>
>>> dscp
>>
>>> resources. Every voice card takes up different numbers. Also the more
>>>>
>>> farms
>>
>>> you have, the lesser the dscp resource left. If you can, remove a voice
>>>>
>>> card
>>
>>> you have installed then see if the number increase.
>>>>
>>>> Let us know your findings.
>>>>
>>>> Babatunde Sanda B.Sc (Acct.) CCNP, CCVP, CCNA(R,S,V), MCSA, N+, A+.
>>>> :: Sent from my Iphone. Apologies for errors and brevity. ::
>>>>
>>>> On Feb 4, 2011, at 8:43 PM, Tortle Tang <tortletang_at_hotmail.com> wrote:
>>>>
>>>> 2811 support the following cmd and 2801 doesn't. Howerver , after
>>>>>
>>>> trying
>>
>>> the
>>>>
>>>>> cmds in 2811, the max sesscion in conference still is 0. (2xPVDM16)
>>>>>
>>>>> voice-card 0
>>>>> dspfarm
>>>>> dsp services dspfarm
>>>>>
>>>>>
>>>>> Thanks,
>>>>> Tortle
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>
>>>>> From: tortletang_at_hotmail.com
>>>>> To: carl.gosselin_at_altizone.com
>>>>> CC: ccielab_at_groupstudy.com
>>>>> Subject: RE: PVDM2 in voice lab
>>>>> Date: Sat, 5 Feb 2011 15:29:11 +1100
>>>>>
>>>>>
>>>>>
>>>>>
>>>>> I tried, it doesn't work.
>>>>>
>>>>> voice-card 0
>>>>> dspfarm----this command isn't supported.
>>>>> dsp services dspfarm
>>>>>
>>>>>
>>>>>
>>>>> Thanks,
>>>>> Tortle
>>>>>
>>>>>
>>>>>
>>>>>
>>>>> Date: Fri, 4 Feb 2011 22:20:48 -0500
>>>>>> Subject: Re: PVDM2 in voice lab
>>>>>> From: carl.gosselin_at_altizone.com
>>>>>> To: tortletang_at_hotmail.com
>>>>>> CC: ccielab_at_groupstudy.com
>>>>>>
>>>>>> Try this...
>>>>>>
>>>>>> !
>>>>>> voice-card 0
>>>>>> dspfarm
>>>>>> dsp services dspfarm
>>>>>> !
>>>>>>
>>>>>> /Carl
>>>>>>
>>>>>> On Fri, Feb 4, 2011 at 10:14 PM, Tortle Tang <tortletang_at_hotmail.com>
>>>>>>
>>>>> wrote:
>>>>>
>>>>>> Hi Guys
>>>>>>>
>>>>>>> I have 2xPVDM2-16 in 2 slots, but when I configure " dspfarm profile
>>>>>>>
>>>>>> 1
>>
>>> conference", The max session is only 0. If I replace 2xPVDM2-16 with
>>>>>>> 1xPVDM2
>>>>>>> 48, I won't have any problem.
>>>>>>>
>>>>>>> Any idea ?
>>>>>>>
>>>>>>>
>>>>>>> R2#sh diag | in PVDM
>>>>>>> PVDM Slot 0:
>>>>>>> 16-channel (G.711) Voice/Fax PVDMII DSP SIMM PVDM daughter card
>>>>>>> Product (FRU) Number : PVDM2-16
>>>>>>> PVDM Slot 1:
>>>>>>> 16-channel (G.711) Voice/Fax PVDMII DSP SIMM PVDM daughter card
>>>>>>> Product (FRU) Number : PVDM2-16
>>>>>>>
>>>>>>>
>>>>>>> voice-card 0
>>>>>>> dsp services dspfarm
>>>>>>>
>>>>>>> R2(config)#dspfarm profile 1 conference
>>>>>>> R2(config-dspfarm-profile)#max
>>>>>>> R2(config-dspfarm-profile)#maximum se
>>>>>>> R2(config-dspfarm-profile)#maximum sessions ?
>>>>>>> <0-0> Number of sessions assigned to this profile
>>>>>>>
>>>>>>> Thanks,
>>>>>>>
>>>>>>>
>>>>>>> Blogs and organic groups at http://www.ccie.net
>>>>>>>
>>>>>>>
>>>>>>>
Received on Mon Feb 07 2011 - 18:39:29 ART