Re: PVDM2 in voice lab

Tortle,

Some hits:

You've got 2xPVDM2-16 in your router.

1. Take both of them out physically and then reboot the router. (also take
any E1 or FXS/FXO module out of the box).
>>>do "show diag" - they should not appear in show diag output.

2. Power off the router - insert DSP#1 into slot#1, boot the router
>>> do show diag, you should see that there. if it's not there try
putting PVDM#2 in slot#1. Boot the router. You should see that there. If not
your try both PVDM schips on slot#2. Then try to configure the PVDM.

The whole purpose of this excercise is to make sure:
a) your both PVDM's are okay
b) Your both slots are okay.

Once above is done then you can go and try your IOS upgrade.

HTH

On Mon, Feb 7, 2011 at 6:39 PM, Tortle Tang <tortletang_at_hotmail.com> wrote:

> Hi Guys
>
> Thanks your kindly support. However it sitll doesn't work after the
> "test"command on my different routers. Prbably I will tried different IOS.
>
> Thanks,
> Tortle
>
>
>
>
>
> ------------------------------
> Date: Mon, 7 Feb 2011 17:57:43 +1100
>
> Subject: Re: PVDM2 in voice lab
> From: pbhatkoti_at_gmail.com
> To: matthn_at_gmail.com
> CC: tron_at_huapi.ba.ar; tortletang_at_hotmail.com; sbabatunde1_at_ca.rr.com;
> carl.gosselin_at_altizone.com; ccielab_at_groupstudy.com
>
>
> u can test the DSP if they're good or bad using 'test' command.
> or hook into a different router. could be ios that u are running is not
> supporting it.
>
> On Mon, Feb 7, 2011 at 9:38 AM, Nick Matthews <matthn_at_gmail.com> wrote:
>
> One of those DSPs may be bad - FAIL is not a good state. You may want a
> TAC
> case to investigate for a replacement.
>
> -nick
>
> On Sat, Feb 5, 2011 at 7:23 PM, Carlos G Mendioroz <tron_at_huapi.ba.ar>
> wrote:
>
> > Some PVDMs are ... not that good, and they fail to start reliably.
> > You can power bounce the router to see if they both come up.
> > A better way is to reset them, with test reset:
> >
> > Router# test dsp device <slot> <id> reset
> >
> > <id> would be 1 for PVDM2-16, <slot> would be 1 or 2.
> >
> > -Carlos
> >
> > Tortle Tang @ 05/02/2011 18:05 -0300 dixit:
> >
> > Hi
> >> I checked out the " show voice dsp group all" in my 2x2811 and 1x2801,
> the
> >> second PVDM2 16 isn't up always. The PVDM2 16 card is good.
> >> But whatever I tried, only PVDM2 in slot 1 can be enabled. Any idea how
> to
> >> enable it in second slot ?
> >>
> >> R2#sh voice dsp group all
> >> DSP groups on slot 0:
> >> dsp 1:
> >> State: UP, firmware: 23.8.0
> >> Max signal/voice channel: 16/16
> >> Max credits: 240
> >> num_of_sig_chnls_allocated: 3
> >> Transcoding channels allocated: 0
> >> Group: FLEX_GROUP_VOICE, complexity: FLEX
> >> Shared credits: 240, reserved credits: 0
> >> Signaling channels allocated: 3
> >> Voice channels allocated: 0
> >> Credits used: 0
> >> dsp 5:
> >> State: FAIL, firmware: 0.0.0
> >> Max signal/voice channel: 16/16
> >> Max credits: 240
> >> num_of_sig_chnls_allocated: 0
> >> Transcoding channels allocated: 0
> >> Group: FLEX_GROUP_VOICE, complexity: FLEX
> >> Shared credits: 240, reserved credits: 0
> >> Signaling channels allocated: 0
> >> Voice channels allocated: 0
> >> Credits used: 0
> >>
> >>
> >>
> >>
> >>
> >>
> >> Thanks,
> >>
> >> Tortle
> >>
> >>
> >>
> >> From: matthn_at_gmail.com
> >>> Date: Sat, 5 Feb 2011 10:12:45 -0500
> >>> Subject: Re: PVDM2 in voice lab
> >>> To: sbabatunde1_at_ca.rr.com
> >>> CC: tortletang_at_hotmail.com; carl.gosselin_at_altizone.com;
> >>>
> >> ccielab_at_groupstudy.com
> >>
> >>> Check out 'show voice dsp group all'
> >>>
> >>> This will list the DSPs and what is being used on each. Each 16 is 1
> DSP,
> >>> and conferencing takes up an entire DSP whether a conference is going
> on
> >>> or
> >>> not. Like mentioned, you've likely got a T1/E1 that's eating partially
> >>> through the 2nd DSP.
> >>>
> >>> There shouldn't be a difference between 2801/2811/2901/2911/etc.
> >>>
> >>> -nick
> >>>
> >>> On Sat, Feb 5, 2011 at 8:19 AM, Babatunde Sanda
> >>>
> >> <sbabatunde1_at_ca.rr.com>wrote:
> >>
> >>> If you already have cards like fxo and fxs installed, this cards are
> >>>>
> >>> given
> >>
> >>> priority over your farms. Remember the purpose of dscpfarms is to share
> >>>>
> >>> dscp
> >>
> >>> resources. Every voice card takes up different numbers. Also the more
> >>>>
> >>> farms
> >>
> >>> you have, the lesser the dscp resource left. If you can, remove a voice
> >>>>
> >>> card
> >>
> >>> you have installed then see if the number increase.
> >>>>
> >>>> Let us know your findings.
> >>>>
> >>>> Babatunde Sanda B.Sc (Acct.) CCNP, CCVP, CCNA(R,S,V), MCSA, N+, A+.
> >>>> :: Sent from my Iphone. Apologies for errors and brevity. ::
> >>>>
> >>>> On Feb 4, 2011, at 8:43 PM, Tortle Tang <tortletang_at_hotmail.com>
> wrote:
> >>>>
> >>>> 2811 support the following cmd and 2801 doesn't. Howerver , after
> >>>>>
> >>>> trying
> >>
> >>> the
> >>>>
> >>>>> cmds in 2811, the max sesscion in conference still is 0. (2xPVDM16)
> >>>>>
> >>>>> voice-card 0
> >>>>> dspfarm
> >>>>> dsp services dspfarm
> >>>>>
> >>>>>
> >>>>> Thanks,
> >>>>> Tortle
> >>>>>
> >>>>>
> >>>>>
> >>>>>
> >>>>>
> >>>>>
> >>>>>
> >>>>> From: tortletang_at_hotmail.com
> >>>>> To: carl.gosselin_at_altizone.com
> >>>>> CC: ccielab_at_groupstudy.com
> >>>>> Subject: RE: PVDM2 in voice lab
> >>>>> Date: Sat, 5 Feb 2011 15:29:11 +1100
> >>>>>
> >>>>>
> >>>>>
> >>>>>
> >>>>> I tried, it doesn't work.
> >>>>>
> >>>>> voice-card 0
> >>>>> dspfarm----this command isn't supported.
> >>>>> dsp services dspfarm
> >>>>>
> >>>>>
> >>>>>
> >>>>> Thanks,
> >>>>> Tortle
> >>>>>
> >>>>>
> >>>>>
> >>>>>
> >>>>> Date: Fri, 4 Feb 2011 22:20:48 -0500
> >>>>>> Subject: Re: PVDM2 in voice lab
> >>>>>> From: carl.gosselin_at_altizone.com
> >>>>>> To: tortletang_at_hotmail.com
> >>>>>> CC: ccielab_at_groupstudy.com
> >>>>>>
> >>>>>> Try this...
> >>>>>>
> >>>>>> !
> >>>>>> voice-card 0
> >>>>>> dspfarm
> >>>>>> dsp services dspfarm
> >>>>>> !
> >>>>>>
> >>>>>> /Carl
> >>>>>>
> >>>>>> On Fri, Feb 4, 2011 at 10:14 PM, Tortle Tang <
> tortletang_at_hotmail.com>
> >>>>>>
> >>>>> wrote:
> >>>>>
> >>>>>> Hi Guys
> >>>>>>>
> >>>>>>> I have 2xPVDM2-16 in 2 slots, but when I configure " dspfarm
> profile
> >>>>>>>
> >>>>>> 1
> >>
> >>> conference", The max session is only 0. If I replace 2xPVDM2-16 with
> >>>>>>> 1xPVDM2
> >>>>>>> 48, I won't have any problem.
> >>>>>>>
> >>>>>>> Any idea ?
> >>>>>>>
> >>>>>>>
> >>>>>>> R2#sh diag | in PVDM
> >>>>>>> PVDM Slot 0:
> >>>>>>> 16-channel (G.711) Voice/Fax PVDMII DSP SIMM PVDM daughter card
> >>>>>>> Product (FRU) Number : PVDM2-16
> >>>>>>> PVDM Slot 1:
> >>>>>>> 16-channel (G.711) Voice/Fax PVDMII DSP SIMM PVDM daughter card
> >>>>>>> Product (FRU) Number : PVDM2-16
> >>>>>>>
> >>>>>>>
> >>>>>>> voice-card 0
> >>>>>>> dsp services dspfarm
> >>>>>>>
> >>>>>>> R2(config)#dspfarm profile 1 conference
> >>>>>>> R2(config-dspfarm-profile)#max
> >>>>>>> R2(config-dspfarm-profile)#maximum se
> >>>>>>> R2(config-dspfarm-profile)#maximum sessions ?
> >>>>>>> <0-0> Number of sessions assigned to this profile
> >>>>>>>
> >>>>>>> Thanks,
> >>>>>>>
> >>>>>>>
> >>>>>>> Blogs and organic groups at http://www.ccie.net
> >>>>>>>
> >>>>>>>
> >>>>>>>
> _______________________________________________________________________
> >>
> >>> Subscription information may be found at:
> >>>>>>> http://www.groupstudy.com/list/CCIELab.html
> >>>>>>>
> >>>>>>>
> >>>>>>>
> >>>>>>>
> >>>>>>>
> >>>>>>>
> >>>>>>>
> >>>>>>>
> >>>>>>>
> >>>>>> --
> >>>>>> ========================
> >>>>>> Carl Gosselin CCIE Voice #15228
> >>>>>> AltiZONE inc.
> >>>>>> Mob: 514-458-9665
> >>>>>>
> >>>>>>
> >>>>>> Blogs and organic groups at http://www.ccie.net
> >>>>>>
> >>>>>>
> >>>>>>
> _______________________________________________________________________
> >>
> >>> Subscription information may be found at:
> >>>>>> http://www.groupstudy.com/list/CCIELab.html
> >>>>>>
> >>>>>
> >>>>> Blogs and organic groups at http://www.ccie.net
> >>>>>
> >>>>>
> _______________________________________________________________________
> >>>>> Subscription information may be found at:
> >>>>> http://www.groupstudy.com/list/CCIELab.html
> >>>>>
> >>>>
> >>>> Blogs and organic groups at http://www.ccie.net
> >>>>
> >>>>
> _______________________________________________________________________
> >>>> Subscription information may be found at:
> >>>> http://www.groupstudy.com/list/CCIELab.html
> >>>>
> >>>
> >>> Blogs and organic groups at http://www.ccie.net
> >>>
> >>> _______________________________________________________________________
> >>> Subscription information may be found at:
> >>> http://www.groupstudy.com/list/CCIELab.html
> >>>
> >>
> >>
> >> Blogs and organic groups at http://www.ccie.net
> >>
> >> _______________________________________________________________________
> >> Subscription information may be found at:
> >> http://www.groupstudy.com/list/CCIELab.html
> >>
> >>
> >>
> >>
> >>
> >>
> >>
> >>
> > --
> > Carlos G Mendioroz <tron_at_huapi.ba.ar> LW7 EQI Argentina
>
>
> Blogs and organic groups at http://www.ccie.net
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html

Blogs and organic groups at http://www.ccie.net
Received on Mon Feb 07 2011 - 23:27:35 ART