RE: PVDM2 in voice lab

Hi

   I tried that, I think both PVDMs and slots are good. I will upgrade the
IOS. Thanks your kindly reply.

Thanks,
Tortle

> Date: Mon, 7 Feb 2011 23:27:35 +1100
> Subject: Re: PVDM2 in voice lab
> From: pbhatkoti_at_gmail.com
> To: tortletang_at_hotmail.com
> CC: matthn_at_gmail.com; tron_at_huapi.ba.ar; sbabatunde1_at_ca.rr.com;
carl.gosselin_at_altizone.com; ccielab_at_groupstudy.com
>
> Tortle,
>
> Some hits:
>
> You've got 2xPVDM2-16 in your router.
>
> 1. Take both of them out physically and then reboot the router. (also take
> any E1 or FXS/FXO module out of the box).
> >>>do "show diag" - they should not appear in show diag output.
>
> 2. Power off the router - insert DSP#1 into slot#1, boot the router
> >>> do show diag, you should see that there. if it's not there try
> putting PVDM#2 in slot#1. Boot the router. You should see that there. If
not
> your try both PVDM schips on slot#2. Then try to configure the PVDM.
>
> The whole purpose of this excercise is to make sure:
> a) your both PVDM's are okay
> b) Your both slots are okay.
>
>
> Once above is done then you can go and try your IOS upgrade.
>
>
> HTH
>
>
> On Mon, Feb 7, 2011 at 6:39 PM, Tortle Tang <tortletang_at_hotmail.com> wrote:
>
> > Hi Guys
> >
> > Thanks your kindly support. However it sitll doesn't work after the
> > "test"command on my different routers. Prbably I will tried different
IOS.
> >
> > Thanks,
> > Tortle
> >
> >
> >
> >
> >
> > ------------------------------
> > Date: Mon, 7 Feb 2011 17:57:43 +1100
> >
> > Subject: Re: PVDM2 in voice lab
> > From: pbhatkoti_at_gmail.com
> > To: matthn_at_gmail.com
> > CC: tron_at_huapi.ba.ar; tortletang_at_hotmail.com; sbabatunde1_at_ca.rr.com;
> > carl.gosselin_at_altizone.com; ccielab_at_groupstudy.com
> >
> >
> > u can test the DSP if they're good or bad using 'test' command.
> > or hook into a different router. could be ios that u are running is not
> > supporting it.
> >
> > On Mon, Feb 7, 2011 at 9:38 AM, Nick Matthews <matthn_at_gmail.com> wrote:
> >
> > One of those DSPs may be bad - FAIL is not a good state. You may want a
> > TAC
> > case to investigate for a replacement.
> >
> > -nick
> >
> > On Sat, Feb 5, 2011 at 7:23 PM, Carlos G Mendioroz <tron_at_huapi.ba.ar>
> > wrote:
> >
> > > Some PVDMs are ... not that good, and they fail to start reliably.
> > > You can power bounce the router to see if they both come up.
> > > A better way is to reset them, with test reset:
> > >
> > > Router# test dsp device <slot> <id> reset
> > >
> > > <id> would be 1 for PVDM2-16, <slot> would be 1 or 2.
> > >
> > > -Carlos
> > >
> > > Tortle Tang @ 05/02/2011 18:05 -0300 dixit:
> > >
> > > Hi
> > >> I checked out the " show voice dsp group all" in my 2x2811 and 1x2801,
> > the
> > >> second PVDM2 16 isn't up always. The PVDM2 16 card is good.
> > >> But whatever I tried, only PVDM2 in slot 1 can be enabled. Any idea
how
> > to
> > >> enable it in second slot ?
> > >>
> > >> R2#sh voice dsp group all
> > >> DSP groups on slot 0:
> > >> dsp 1:
> > >> State: UP, firmware: 23.8.0
> > >> Max signal/voice channel: 16/16
> > >> Max credits: 240
> > >> num_of_sig_chnls_allocated: 3
> > >> Transcoding channels allocated: 0
> > >> Group: FLEX_GROUP_VOICE, complexity: FLEX
> > >> Shared credits: 240, reserved credits: 0
> > >> Signaling channels allocated: 3
> > >> Voice channels allocated: 0
> > >> Credits used: 0
> > >> dsp 5:
> > >> State: FAIL, firmware: 0.0.0
> > >> Max signal/voice channel: 16/16
> > >> Max credits: 240
> > >> num_of_sig_chnls_allocated: 0
> > >> Transcoding channels allocated: 0
> > >> Group: FLEX_GROUP_VOICE, complexity: FLEX
> > >> Shared credits: 240, reserved credits: 0
> > >> Signaling channels allocated: 0
> > >> Voice channels allocated: 0
> > >> Credits used: 0
> > >>
> > >>
> > >>
> > >>
> > >>
> > >>
> > >> Thanks,
> > >>
> > >> Tortle
> > >>
> > >>
> > >>
> > >> From: matthn_at_gmail.com
> > >>> Date: Sat, 5 Feb 2011 10:12:45 -0500
> > >>> Subject: Re: PVDM2 in voice lab
> > >>> To: sbabatunde1_at_ca.rr.com
> > >>> CC: tortletang_at_hotmail.com; carl.gosselin_at_altizone.com;
> > >>>
> > >> ccielab_at_groupstudy.com
> > >>
> > >>> Check out 'show voice dsp group all'
> > >>>
> > >>> This will list the DSPs and what is being used on each. Each 16 is 1
> > DSP,
> > >>> and conferencing takes up an entire DSP whether a conference is going
> > on
> > >>> or
> > >>> not. Like mentioned, you've likely got a T1/E1 that's eating
partially
> > >>> through the 2nd DSP.
> > >>>
> > >>> There shouldn't be a difference between 2801/2811/2901/2911/etc.
> > >>>
> > >>> -nick
> > >>>
> > >>> On Sat, Feb 5, 2011 at 8:19 AM, Babatunde Sanda
> > >>>
> > >> <sbabatunde1_at_ca.rr.com>wrote:
> > >>
> > >>> If you already have cards like fxo and fxs installed, this cards are
> > >>>>
> > >>> given
> > >>
> > >>> priority over your farms. Remember the purpose of dscpfarms is to
share
> > >>>>
> > >>> dscp
> > >>
> > >>> resources. Every voice card takes up different numbers. Also the more
> > >>>>
> > >>> farms
> > >>
> > >>> you have, the lesser the dscp resource left. If you can, remove a
voice
> > >>>>
> > >>> card
> > >>
> > >>> you have installed then see if the number increase.
> > >>>>
> > >>>> Let us know your findings.
> > >>>>
> > >>>> Babatunde Sanda B.Sc (Acct.) CCNP, CCVP, CCNA(R,S,V), MCSA, N+, A+.
> > >>>> :: Sent from my Iphone. Apologies for errors and brevity. ::
> > >>>>
> > >>>> On Feb 4, 2011, at 8:43 PM, Tortle Tang <tortletang_at_hotmail.com>
> > wrote:
> > >>>>
> > >>>> 2811 support the following cmd and 2801 doesn't. Howerver , after
> > >>>>>
> > >>>> trying
> > >>
> > >>> the
> > >>>>
> > >>>>> cmds in 2811, the max sesscion in conference still is 0. (2xPVDM16)
> > >>>>>
> > >>>>> voice-card 0
> > >>>>> dspfarm
> > >>>>> dsp services dspfarm
> > >>>>>
> > >>>>>
> > >>>>> Thanks,
> > >>>>> Tortle
> > >>>>>
> > >>>>>
> > >>>>>
> > >>>>>
> > >>>>>
> > >>>>>
> > >>>>>
> > >>>>> From: tortletang_at_hotmail.com
> > >>>>> To: carl.gosselin_at_altizone.com
> > >>>>> CC: ccielab_at_groupstudy.com
> > >>>>> Subject: RE: PVDM2 in voice lab
> > >>>>> Date: Sat, 5 Feb 2011 15:29:11 +1100
> > >>>>>
> > >>>>>
> > >>>>>
> > >>>>>
> > >>>>> I tried, it doesn't work.
> > >>>>>
> > >>>>> voice-card 0
> > >>>>> dspfarm----this command isn't supported.
> > >>>>> dsp services dspfarm
> > >>>>>
> > >>>>>
> > >>>>>
> > >>>>> Thanks,
> > >>>>> Tortle
> > >>>>>
> > >>>>>
> > >>>>>
> > >>>>>
> > >>>>> Date: Fri, 4 Feb 2011 22:20:48 -0500
> > >>>>>> Subject: Re: PVDM2 in voice lab
> > >>>>>> From: carl.gosselin_at_altizone.com
> > >>>>>> To: tortletang_at_hotmail.com
> > >>>>>> CC: ccielab_at_groupstudy.com
> > >>>>>>
> > >>>>>> Try this...
> > >>>>>>
> > >>>>>> !
> > >>>>>> voice-card 0
> > >>>>>> dspfarm
> > >>>>>> dsp services dspfarm
> > >>>>>> !
> > >>>>>>
> > >>>>>> /Carl
> > >>>>>>
> > >>>>>> On Fri, Feb 4, 2011 at 10:14 PM, Tortle Tang <
> > tortletang_at_hotmail.com>
> > >>>>>>
> > >>>>> wrote:
> > >>>>>
> > >>>>>> Hi Guys
> > >>>>>>>
> > >>>>>>> I have 2xPVDM2-16 in 2 slots, but when I configure " dspfarm
> > profile
> > >>>>>>>
> > >>>>>> 1
> > >>
> > >>> conference", The max session is only 0. If I replace 2xPVDM2-16 with
> > >>>>>>> 1xPVDM2
> > >>>>>>> 48, I won't have any problem.
> > >>>>>>>
> > >>>>>>> Any idea ?
> > >>>>>>>
> > >>>>>>>
> > >>>>>>> R2#sh diag | in PVDM
> > >>>>>>> PVDM Slot 0:
> > >>>>>>> 16-channel (G.711) Voice/Fax PVDMII DSP SIMM PVDM daughter card
> > >>>>>>> Product (FRU) Number : PVDM2-16
> > >>>>>>> PVDM Slot 1:
> > >>>>>>> 16-channel (G.711) Voice/Fax PVDMII DSP SIMM PVDM daughter card
> > >>>>>>> Product (FRU) Number : PVDM2-16
> > >>>>>>>
> > >>>>>>>
> > >>>>>>> voice-card 0
> > >>>>>>> dsp services dspfarm
> > >>>>>>>
> > >>>>>>> R2(config)#dspfarm profile 1 conference
> > >>>>>>> R2(config-dspfarm-profile)#max
> > >>>>>>> R2(config-dspfarm-profile)#maximum se
> > >>>>>>> R2(config-dspfarm-profile)#maximum sessions ?
> > >>>>>>> <0-0> Number of sessions assigned to this profile
> > >>>>>>>
> > >>>>>>> Thanks,
> > >>>>>>>
> > >>>>>>>
> > >>>>>>> Blogs and organic groups at http://www.ccie.net
> > >>>>>>>
> > >>>>>>>
> > >>>>>>>
> > _______________________________________________________________________
> > >>
> > >>> Subscription information may be found at:
> > >>>>>>> http://www.groupstudy.com/list/CCIELab.html
> > >>>>>>>
> > >>>>>>>
> > >>>>>>>
> > >>>>>>>
> > >>>>>>>
> > >>>>>>>
> > >>>>>>>
> > >>>>>>>
> > >>>>>>>
> > >>>>>> --
> > >>>>>> ========================
> > >>>>>> Carl Gosselin CCIE Voice #15228
> > >>>>>> AltiZONE inc.
> > >>>>>> Mob: 514-458-9665
> > >>>>>>
> > >>>>>>
> > >>>>>> Blogs and organic groups at http://www.ccie.net
> > >>>>>>
> > >>>>>>
> > >>>>>>
> > _______________________________________________________________________
> > >>
> > >>> Subscription information may be found at:
> > >>>>>> http://www.groupstudy.com/list/CCIELab.html
> > >>>>>>
> > >>>>>
> > >>>>> Blogs and organic groups at http://www.ccie.net
> > >>>>>
> > >>>>>
> > _______________________________________________________________________
> > >>>>> Subscription information may be found at:
> > >>>>> http://www.groupstudy.com/list/CCIELab.html
> > >>>>>
> > >>>>
> > >>>> Blogs and organic groups at http://www.ccie.net
> > >>>>
> > >>>>
> > _______________________________________________________________________
> > >>>> Subscription information may be found at:
> > >>>> http://www.groupstudy.com/list/CCIELab.html
> > >>>>
> > >>>
> > >>> Blogs and organic groups at http://www.ccie.net
> > >>>
> > >>>
Received on Wed Feb 09 2011 - 12:29:43 ART