Re: PVDM2 in voice lab

u can test the DSP if they're good or bad using 'test' command.
or hook into a different router. could be ios that u are running is not
supporting it.

On Mon, Feb 7, 2011 at 9:38 AM, Nick Matthews <matthn_at_gmail.com> wrote:

> One of those DSPs may be bad - FAIL is not a good state. You may want a
> TAC
> case to investigate for a replacement.
>
> -nick
>
> On Sat, Feb 5, 2011 at 7:23 PM, Carlos G Mendioroz <tron_at_huapi.ba.ar>
> wrote:
>
> > Some PVDMs are ... not that good, and they fail to start reliably.
> > You can power bounce the router to see if they both come up.
> > A better way is to reset them, with test reset:
> >
> > Router# test dsp device <slot> <id> reset
> >
> > <id> would be 1 for PVDM2-16, <slot> would be 1 or 2.
> >
> > -Carlos
> >
> > Tortle Tang @ 05/02/2011 18:05 -0300 dixit:
> >
> > Hi
> >> I checked out the " show voice dsp group all" in my 2x2811 and 1x2801,
> the
> >> second PVDM2 16 isn't up always. The PVDM2 16 card is good.
> >> But whatever I tried, only PVDM2 in slot 1 can be enabled. Any idea how
> to
> >> enable it in second slot ?
> >>
> >> R2#sh voice dsp group all
> >> DSP groups on slot 0:
> >> dsp 1:
> >> State: UP, firmware: 23.8.0
> >> Max signal/voice channel: 16/16
> >> Max credits: 240
> >> num_of_sig_chnls_allocated: 3
> >> Transcoding channels allocated: 0
> >> Group: FLEX_GROUP_VOICE, complexity: FLEX
> >> Shared credits: 240, reserved credits: 0
> >> Signaling channels allocated: 3
> >> Voice channels allocated: 0
> >> Credits used: 0
> >> dsp 5:
> >> State: FAIL, firmware: 0.0.0
> >> Max signal/voice channel: 16/16
> >> Max credits: 240
> >> num_of_sig_chnls_allocated: 0
> >> Transcoding channels allocated: 0
> >> Group: FLEX_GROUP_VOICE, complexity: FLEX
> >> Shared credits: 240, reserved credits: 0
> >> Signaling channels allocated: 0
> >> Voice channels allocated: 0
> >> Credits used: 0
> >>
> >>
> >>
> >>
> >>
> >>
> >> Thanks,
> >>
> >> Tortle
> >>
> >>
> >>
> >> From: matthn_at_gmail.com
> >>> Date: Sat, 5 Feb 2011 10:12:45 -0500
> >>> Subject: Re: PVDM2 in voice lab
> >>> To: sbabatunde1_at_ca.rr.com
> >>> CC: tortletang_at_hotmail.com; carl.gosselin_at_altizone.com;
> >>>
> >> ccielab_at_groupstudy.com
> >>
> >>> Check out 'show voice dsp group all'
> >>>
> >>> This will list the DSPs and what is being used on each. Each 16 is 1
> DSP,
> >>> and conferencing takes up an entire DSP whether a conference is going
> on
> >>> or
> >>> not. Like mentioned, you've likely got a T1/E1 that's eating partially
> >>> through the 2nd DSP.
> >>>
> >>> There shouldn't be a difference between 2801/2811/2901/2911/etc.
> >>>
> >>> -nick
> >>>
> >>> On Sat, Feb 5, 2011 at 8:19 AM, Babatunde Sanda
> >>>
> >> <sbabatunde1_at_ca.rr.com>wrote:
> >>
> >>> If you already have cards like fxo and fxs installed, this cards are
> >>>>
> >>> given
> >>
> >>> priority over your farms. Remember the purpose of dscpfarms is to share
> >>>>
> >>> dscp
> >>
> >>> resources. Every voice card takes up different numbers. Also the more
> >>>>
> >>> farms
> >>
> >>> you have, the lesser the dscp resource left. If you can, remove a voice
> >>>>
> >>> card
> >>
> >>> you have installed then see if the number increase.
> >>>>
> >>>> Let us know your findings.
> >>>>
> >>>> Babatunde Sanda B.Sc (Acct.) CCNP, CCVP, CCNA(R,S,V), MCSA, N+, A+.
> >>>> :: Sent from my Iphone. Apologies for errors and brevity. ::
> >>>>
> >>>> On Feb 4, 2011, at 8:43 PM, Tortle Tang <tortletang_at_hotmail.com>
> wrote:
> >>>>
> >>>> 2811 support the following cmd and 2801 doesn't. Howerver , after
> >>>>>
> >>>> trying
> >>
> >>> the
> >>>>
> >>>>> cmds in 2811, the max sesscion in conference still is 0. (2xPVDM16)
> >>>>>
> >>>>> voice-card 0
> >>>>> dspfarm
> >>>>> dsp services dspfarm
> >>>>>
> >>>>>
> >>>>> Thanks,
> >>>>> Tortle
> >>>>>
> >>>>>
> >>>>>
> >>>>>
> >>>>>
> >>>>>
> >>>>>
> >>>>> From: tortletang_at_hotmail.com
> >>>>> To: carl.gosselin_at_altizone.com
> >>>>> CC: ccielab_at_groupstudy.com
> >>>>> Subject: RE: PVDM2 in voice lab
> >>>>> Date: Sat, 5 Feb 2011 15:29:11 +1100
> >>>>>
> >>>>>
> >>>>>
> >>>>>
> >>>>> I tried, it doesn't work.
> >>>>>
> >>>>> voice-card 0
> >>>>> dspfarm----this command isn't supported.
> >>>>> dsp services dspfarm
> >>>>>
> >>>>>
> >>>>>
> >>>>> Thanks,
> >>>>> Tortle
> >>>>>
> >>>>>
> >>>>>
> >>>>>
> >>>>> Date: Fri, 4 Feb 2011 22:20:48 -0500
> >>>>>> Subject: Re: PVDM2 in voice lab
> >>>>>> From: carl.gosselin_at_altizone.com
> >>>>>> To: tortletang_at_hotmail.com
> >>>>>> CC: ccielab_at_groupstudy.com
> >>>>>>
> >>>>>> Try this...
> >>>>>>
> >>>>>> !
> >>>>>> voice-card 0
> >>>>>> dspfarm
> >>>>>> dsp services dspfarm
> >>>>>> !
> >>>>>>
> >>>>>> /Carl
> >>>>>>
> >>>>>> On Fri, Feb 4, 2011 at 10:14 PM, Tortle Tang <
> tortletang_at_hotmail.com>
> >>>>>>
> >>>>> wrote:
> >>>>>
> >>>>>> Hi Guys
> >>>>>>>
> >>>>>>> I have 2xPVDM2-16 in 2 slots, but when I configure " dspfarm
> profile
> >>>>>>>
> >>>>>> 1
> >>
> >>> conference", The max session is only 0. If I replace 2xPVDM2-16 with
> >>>>>>> 1xPVDM2
> >>>>>>> 48, I won't have any problem.
> >>>>>>>
> >>>>>>> Any idea ?
> >>>>>>>
> >>>>>>>
> >>>>>>> R2#sh diag | in PVDM
> >>>>>>> PVDM Slot 0:
> >>>>>>> 16-channel (G.711) Voice/Fax PVDMII DSP SIMM PVDM daughter card
> >>>>>>> Product (FRU) Number : PVDM2-16
> >>>>>>> PVDM Slot 1:
> >>>>>>> 16-channel (G.711) Voice/Fax PVDMII DSP SIMM PVDM daughter card
> >>>>>>> Product (FRU) Number : PVDM2-16
> >>>>>>>
> >>>>>>>
> >>>>>>> voice-card 0
> >>>>>>> dsp services dspfarm
> >>>>>>>
> >>>>>>> R2(config)#dspfarm profile 1 conference
> >>>>>>> R2(config-dspfarm-profile)#max
> >>>>>>> R2(config-dspfarm-profile)#maximum se
> >>>>>>> R2(config-dspfarm-profile)#maximum sessions ?
> >>>>>>> <0-0> Number of sessions assigned to this profile
> >>>>>>>
> >>>>>>> Thanks,
> >>>>>>>
> >>>>>>>
> >>>>>>> Blogs and organic groups at http://www.ccie.net
> >>>>>>>
> >>>>>>>
> >>>>>>>
> _______________________________________________________________________
> >>
> >>> Subscription information may be found at:
> >>>>>>> http://www.groupstudy.com/list/CCIELab.html
> >>>>>>>
> >>>>>>>
> >>>>>>>
> >>>>>>>
> >>>>>>>
> >>>>>>>
> >>>>>>>
> >>>>>>>
> >>>>>>>
> >>>>>> --
> >>>>>> ========================
> >>>>>> Carl Gosselin CCIE Voice #15228
> >>>>>> AltiZONE inc.
> >>>>>> Mob: 514-458-9665
> >>>>>>
> >>>>>>
> >>>>>> Blogs and organic groups at http://www.ccie.net
> >>>>>>
> >>>>>>
> >>>>>>
> _______________________________________________________________________
> >>
> >>> Subscription information may be found at:
> >>>>>> http://www.groupstudy.com/list/CCIELab.html
> >>>>>>
> >>>>>
> >>>>> Blogs and organic groups at http://www.ccie.net
> >>>>>
> >>>>>
> _______________________________________________________________________
> >>>>> Subscription information may be found at:
> >>>>> http://www.groupstudy.com/list/CCIELab.html
> >>>>>
> >>>>
> >>>> Blogs and organic groups at http://www.ccie.net
> >>>>
> >>>>
> _______________________________________________________________________
> >>>> Subscription information may be found at:
> >>>> http://www.groupstudy.com/list/CCIELab.html
> >>>>
> >>>
> >>> Blogs and organic groups at http://www.ccie.net
> >>>
> >>> _______________________________________________________________________
> >>> Subscription information may be found at:
> >>> http://www.groupstudy.com/list/CCIELab.html
> >>>
> >>
> >>
> >> Blogs and organic groups at http://www.ccie.net
> >>
> >> _______________________________________________________________________
> >> Subscription information may be found at:
> >> http://www.groupstudy.com/list/CCIELab.html
> >>
> >>
> >>
> >>
> >>
> >>
> >>
> >>
> > --
> > Carlos G Mendioroz <tron_at_huapi.ba.ar> LW7 EQI Argentina
>
>
> Blogs and organic groups at http://www.ccie.net
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html

Blogs and organic groups at http://www.ccie.net
Received on Mon Feb 07 2011 - 17:57:43 ART