Dear bilal:-
i did configure the parameter ppp authentication pap or chap because if i
configure ppp authentication then i must provide username and password but
service provide ask that the usename and password is blank and i am
accessing the internet over my cell phone without any username or password
Thanks a lot
Adnan
On Sat, Oct 30, 2010 at 4:01 PM, Bilal Hansrod <bilal.hansrod_at_gmail.com>wrote:
> What output do you see when you run below debugs suggested by ERDEM
>
> debug chat
> debug ppp negotiation
> debug ppp error
> debug ppp event
>
> Regards,
>
> Bilal
>
>
> On Sun, Oct 31, 2010 at 12:45 AM, muhammad adnan <taurusadnan19_at_gmail.com>wrote:
>
>> Dear
>> i am using internet when i placed my sim in my cell phone.if the Data is
>> not activated then how i can access.
>>
>> Thanks
>>
>>
>>
>>
>>
>> On Sat, Oct 30, 2010 at 3:36 PM, Radioactive Frog <pbhatkoti_at_gmail.com>wrote:
>>
>>> I am not sure if you've already done this but take the SIM card out from
>>> the cellular module and put it in your SmartPhone - Sort out the activation
>>> isssue first. Make sure data is activated on that SIM.
>>>
>>> Then play it once above is confirmed.
>>>
>>>
>>>
>>> On Sat, Oct 30, 2010 at 11:56 PM, muhammad adnan <
>>> taurusadnan19_at_gmail.com> wrote:
>>>
>>>> Dear Bilal
>>>> Router#show cellular 0/1/0 all
>>>> Hardware Information
>>>> ====================
>>>> Modem Firmware Version = H1_1_9_3MCAP C:/WS/
>>>> Modem Firmware built = 12/12/07
>>>> Hardware Version = 1.0
>>>> International Mobile Subscriber Identity (IMSI) = 606010105114370
>>>> International Mobile Equipment Identity (IMEI) = 011359000487907
>>>> Factory Serial Number (FSN) = D28026013381043
>>>> Modem Status = Online
>>>> Current Modem Temperature = 26 deg C, State = Normal
>>>>
>>>> Profile Information
>>>> ====================
>>>> Profile 1 = INACTIVE*
>>>> --------
>>>> PDP Type = IPv4
>>>> Access Point Name (APN) = almadar.net
>>>> Authentication = None
>>>> Username: , Password:
>>>>
>>>> * - Default profile
>>>>
>>>> Data Connection Information
>>>> ===========================
>>>> Data Transmitted = 0 bytes, Received = 0 bytes
>>>> Profile 1, Packet Session Status = INACTIVE
>>>> Inactivity Reason = Normal inactivate state
>>>> Profile 2, Packet Session Status = INACTIVE
>>>> Inactivity Reason = Normal inactivate state
>>>> Profile 3, Packet Session Status = INACTIVE
>>>> Inactivity Reason = Normal inactivate state
>>>> Profile 4, Packet Session Status = INACTIVE
>>>> Inactivity Reason = Normal inactivate state
>>>> Profile 5, Packet Session Status = INACTIVE
>>>> Inactivity Reason = Normal inactivate state
>>>> Profile 6, Packet Session Status = INACTIVE
>>>> Inactivity Reason = Normal inactivate state
>>>> Profile 7, Packet Session Status = INACTIVE
>>>> Inactivity Reason = Normal inactivate state
>>>> Profile 8, Packet Session Status = INACTIVE
>>>> Inactivity Reason = Normal inactivate state
>>>> Profile 9, Packet Session Status = INACTIVE
>>>> Inactivity Reason = Normal inactivate state
>>>> Profile 10, Packet Session Status = INACTIVE
>>>> Inactivity Reason = Normal inactivate state
>>>> Profile 11, Packet Session Status = INACTIVE
>>>> Inactivity Reason = Normal inactivate state
>>>> Profile 12, Packet Session Status = INACTIVE
>>>> Inactivity Reason = Normal inactivate state
>>>> Profile 13, Packet Session Status = INACTIVE
>>>> Inactivity Reason = Normal inactivate state
>>>> Profile 14, Packet Session Status = INACTIVE
>>>> Inactivity Reason = Normal inactivate state
>>>> Profile 15, Packet Session Status = INACTIVE
>>>> Inactivity Reason = Normal inactivate state
>>>> Profile 16, Packet Session Status = INACTIVE
>>>> Inactivity Reason = Normal inactivate state
>>>>
>>>> Network Information
>>>> ===================
>>>> Current Service Status = Normal, Service Error = None
>>>> Current Service = Combined
>>>> Packet Service = GPRS (Attached)
>>>> Packet Session Status = Inactive
>>>> Current Roaming Status = Home
>>>> Network Selection Mode = Automatic
>>>> Country = 606, Network = 606 01
>>>> Mobile Country Code (MCC) = 606
>>>> Mobile Network Code (MNC) = 1
>>>> Location Area Code (LAC) = 1
>>>> Routing Area Code (RAC) = 1
>>>> Cell ID = 11071
>>>> Primary Scrambling Code = 0
>>>> PLMN Selection = Automatic
>>>> Registered PLMN = Libya Al Madar , Abbreviated = 606 01
>>>> Service Provider = 606 01
>>>>
>>>> Radio Information
>>>> =================
>>>> Current Band = GSM 900, Channel Number = 5
>>>> Current RSSI = -62 dBm
>>>> Band Selected = Auto
>>>>
>>>> Modem Security Information
>>>> ==========================
>>>> Card Holder Verification (CHV1) = Disabled
>>>> SIM Status = OK
>>>> SIM User Operation Required = None
>>>> Number of Retries remaining = 3
>>>>
>>>>
>>>> Thanks
>>>>
>>>>
>>>>
>>>>
>>>> On Sat, Oct 30, 2010 at 2:42 PM, Bilal Hansrod <bilal.hansrod_at_gmail.com
>>>> >wrote:
>>>>
>>>> > Can you please send the output of *sh cell 0/1/0 all*
>>>> >
>>>> >
>>>> > Bilal
>>>> >
>>>> >
>>>> > On Sat, Oct 30, 2010 at 11:36 PM, muhammad adnan <
>>>> taurusadnan19_at_gmail.com>wrote:
>>>> >
>>>> >> Dear Bilal i configure according to the Cisco Documentation
>>>> >> and in my mail i pasted show run config...
>>>> >>
>>>> >>
>>>> >>
>>>> >>
>>>> http://www.cisco.com/en/US/docs/routers/access/1800/1861/software/feature/guide/mrwlsgsm.html#wp1040391
>>>> >>
>>>> >> in my mail i ask that username and password is blank to access the
>>>> >> internet
>>>> >> Service provider ask me no authentication username and password blank
>>>> ("i
>>>> >> just put Apn in my phone and username and password blank and it works
>>>> fine
>>>> >> accessing the internet")
>>>> >>
>>>> >> if u need any more information kindly let me know again..
>>>> >>
>>>> >> Thanks
>>>> >> Muhammad Adnan
>>>> >>
>>>> >>
>>>> >>
>>>> >> On Sat, Oct 30, 2010 at 2:28 PM, Bilal Hansrod <
>>>> bilal.hansrod_at_gmail.com>wrote:
>>>> >>
>>>> >>> Hi Muhammad,
>>>> >>>
>>>> >>> I can't see a logical interface created for cell interface where you
>>>> >>> define your PPP username/password and also the authentication
>>>> method.
>>>> >>>
>>>> >>> An example from my config as below:
>>>> >>>
>>>> >>>
>>>> >>> interface Dialer1
>>>> >>> ip address negotiated
>>>> >>> ip virtual-reassembly
>>>> >>> encapsulation ppp
>>>> >>> dialer pool 1
>>>> >>> dialer idle-timeout 0
>>>> >>> dialer string gsm
>>>> >>> dialer persistent
>>>> >>> dialer-group 1
>>>> >>> no cdp enable
>>>> >>> ppp authentication chap callin
>>>> >>> ppp chap hostname XXX
>>>> >>> ppp chap password YYY
>>>> >>>
>>>> >>>
>>>> >>> Regards,
>>>> >>>
>>>> >>> Bilal
>>>> >>>
>>>> >>>
>>>> >>> On Sat, Oct 30, 2010 at 11:05 PM, muhammad adnan <
>>>> >>> taurusadnan19_at_gmail.com> wrote:
>>>> >>>
>>>> >>>> Dear Group members:-
>>>> >>>> i am trying to configure the
>>>> 3G-module.i
>>>> >>>> have inserted my sim card into the HWIC module sim card properly
>>>> >>>> working in
>>>> >>>> the phone and i am accessing the internet.
>>>> >>>> but when i configure HWIC module accordingly i am unable to access
>>>> the
>>>> >>>> internet my configration pasted below if any experience person guid
>>>> me
>>>> >>>> little.
>>>> >>>>
>>>> >>>>
>>>> >>>> in my phone i just put APN and it work fine without Authentication
>>>> >>>> *Service
>>>> >>>> provider ask me* that the *username and password is blank..*
>>>> >>>>
>>>> >>>> country Libya
>>>> >>>> GSM service provider =Almadar
>>>> >>>> APN or access point name =almadar.net
>>>> >>>>
>>>> >>>>
>>>> >>>>
>>>> >>>>
>>>> >>>> *Router#show cellular 0/1/0 profile
>>>> >>>> Profile 1 = INACTIVE*
>>>> >>>> --------
>>>> >>>> PDP Type = IPv4
>>>> >>>> Access Point Name (APN) = almadar.net
>>>> >>>> Authentication = None
>>>> >>>> Username: , Password:
>>>> >>>>
>>>> >>>> * - Default profile
>>>> >>>> *
>>>> >>>>
>>>> >>>>
>>>> --------------------------------------------------------------------------------------
>>>> >>>> *Router config*:
>>>> >>>> *
>>>> >>>> !
>>>> >>>> !
>>>> >>>> !
>>>> >>>> multilink bundle-name authenticated
>>>> >>>> !
>>>> >>>> chat-script gsm "" "ATDT*99*1#" TIMEOUT 60 "CONNECT"
>>>> >>>> !
>>>> >>>> !
>>>> >>>> !
>>>> >>>> !
>>>> >>>> interface Loopback0
>>>> >>>> ip address 10.0.0.1 255.255.255.0
>>>> >>>> !
>>>> >>>> interface Wlan-GigabitEthernet0/0
>>>> >>>> description Internal switch interface connecting to the embedded
>>>> AP
>>>> >>>> !
>>>> >>>> interface GigabitEthernet0/0
>>>> >>>> no ip address
>>>> >>>> shutdown
>>>> >>>> duplex auto
>>>> >>>> speed auto
>>>> >>>> !
>>>> >>>> interface wlan-ap0
>>>> >>>> description Service module interface to manage the embedded AP
>>>> >>>> no ip address
>>>> >>>> arp timeout 0
>>>> >>>> no mop enabled
>>>> >>>> no mop sysid
>>>> >>>> !
>>>> >>>> interface GigabitEthernet0/1
>>>> >>>> no ip address
>>>> >>>> shutdown
>>>> >>>> duplex auto
>>>> >>>> speed auto
>>>> >>>> !
>>>> >>>> interface ATM0/0/0
>>>> >>>> no ip address
>>>> >>>> shutdown
>>>> >>>> no atm ilmi-keepalive
>>>> >>>> !
>>>> >>>> interface Cellular0/1/0
>>>> >>>> ip address negotiated
>>>> >>>> encapsulation ppp
>>>> >>>> dialer in-band
>>>> >>>> dialer idle-timeout 30
>>>> >>>> dialer string gsm
>>>> >>>> dialer-group 1
>>>> >>>> async mode interactive
>>>> >>>> ppp ipcp dns request
>>>> >>>> !
>>>> >>>> interface Vlan1
>>>> >>>> no ip address
>>>> >>>> !
>>>> >>>> ip forward-protocol nd
>>>> >>>> !
>>>> >>>> no ip http server
>>>> >>>> no ip http secure-server
>>>> >>>> !
>>>> >>>> ip route 0.0.0.0 0.0.0.0 Cellular0/1/0
>>>> >>>> !
>>>> >>>> access-list 1 permit any
>>>> >>>> dialer-list 1 protocol ip list 1
>>>> >>>> !
>>>> >>>> !
>>>> >>>> !
>>>> >>>> control-plane
>>>> >>>> !
>>>> >>>> !
>>>> >>>> line con 0
>>>> >>>> line aux 0
>>>> >>>> line 0/1/0
>>>> >>>> exec-timeout 0 0
>>>> >>>> script dialer gsm
>>>> >>>> login
>>>> >>>> modem InOut
>>>> >>>> no exec
>>>> >>>> speed 80000
>>>> >>>> line 67
>>>> >>>> no activation-character
>>>> >>>> no exec
>>>> >>>> transport preferred none
>>>> >>>> transport input all
>>>> >>>> transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
>>>> >>>> line vty 0 4
>>>> >>>> login
>>>> >>>> !
>>>> >>>> scheduler allocate 20000 1000
>>>> >>>> end*
>>>> >>>>
>>>> >>>>
>>>> >>>>
>>>> >>>>
>>>> >>>>
>>>> >>>>
>>>> >>>>
>>>> >>>>
>>>> >>>> kindly Guid me
>>>> >>>>
>>>> >>>>
>>>> >>>> Blogs and organic groups at http://www.ccie.net
>>>> >>>>
>>>> >>>>
>>>> _______________________________________________________________________
>>>> >>>> Subscription information may be found at:
>>>> >>>> http://www.groupstudy.com/list/CCIELab.html
>>>>
>>>>
>>>> Blogs and organic groups at http://www.ccie.net
>>>>
>>>> _______________________________________________________________________
>>>> Subscription information may be found at:
>>>> http://www.groupstudy.com/list/CCIELab.html
Blogs and organic groups at http://www.ccie.net
Received on Sat Oct 30 2010 - 16:09:37 ART
This archive was generated by hypermail 2.2.0 : Mon Nov 01 2010 - 06:42:06 ART