Dear bilal:- one corection --> did not
i *didnot* configure the parameter ppp authentication pap or chap because
if i configure ppp authentication then i must provide username and password
but service provide ask that the usename and password is blank and i am
accessing the internet over my cell phone without any username or password
Thanks a lot
Adnan
On Sat, Oct 30, 2010 at 4:09 PM, muhammad adnan <taurusadnan19_at_gmail.com>wrote:
> Dear bilal:-
> i did configure the parameter ppp authentication pap or chap because if i
> configure ppp authentication then i must provide username and password but
> service provide ask that the usename and password is blank and i am
> accessing the internet over my cell phone without any username or password
>
> Thanks a lot
> Adnan
>
>
> On Sat, Oct 30, 2010 at 4:01 PM, Bilal Hansrod <bilal.hansrod_at_gmail.com>wrote:
>
>> What output do you see when you run below debugs suggested by ERDEM
>>
>> debug chat
>> debug ppp negotiation
>> debug ppp error
>> debug ppp event
>>
>> Regards,
>>
>> Bilal
>>
>>
>> On Sun, Oct 31, 2010 at 12:45 AM, muhammad adnan <taurusadnan19_at_gmail.com
>> > wrote:
>>
>>> Dear
>>> i am using internet when i placed my sim in my cell phone.if the Data is
>>> not activated then how i can access.
>>>
>>> Thanks
>>>
>>>
>>>
>>>
>>>
>>> On Sat, Oct 30, 2010 at 3:36 PM, Radioactive Frog <pbhatkoti_at_gmail.com>wrote:
>>>
>>>> I am not sure if you've already done this but take the SIM card out from
>>>> the cellular module and put it in your SmartPhone - Sort out the activation
>>>> isssue first. Make sure data is activated on that SIM.
>>>>
>>>> Then play it once above is confirmed.
>>>>
>>>>
>>>>
>>>> On Sat, Oct 30, 2010 at 11:56 PM, muhammad adnan <
>>>> taurusadnan19_at_gmail.com> wrote:
>>>>
>>>>> Dear Bilal
>>>>> Router#show cellular 0/1/0 all
>>>>> Hardware Information
>>>>> ====================
>>>>> Modem Firmware Version = H1_1_9_3MCAP C:/WS/
>>>>> Modem Firmware built = 12/12/07
>>>>> Hardware Version = 1.0
>>>>> International Mobile Subscriber Identity (IMSI) = 606010105114370
>>>>> International Mobile Equipment Identity (IMEI) = 011359000487907
>>>>> Factory Serial Number (FSN) = D28026013381043
>>>>> Modem Status = Online
>>>>> Current Modem Temperature = 26 deg C, State = Normal
>>>>>
>>>>> Profile Information
>>>>> ====================
>>>>> Profile 1 = INACTIVE*
>>>>> --------
>>>>> PDP Type = IPv4
>>>>> Access Point Name (APN) = almadar.net
>>>>> Authentication = None
>>>>> Username: , Password:
>>>>>
>>>>> * - Default profile
>>>>>
>>>>> Data Connection Information
>>>>> ===========================
>>>>> Data Transmitted = 0 bytes, Received = 0 bytes
>>>>> Profile 1, Packet Session Status = INACTIVE
>>>>> Inactivity Reason = Normal inactivate state
>>>>> Profile 2, Packet Session Status = INACTIVE
>>>>> Inactivity Reason = Normal inactivate state
>>>>> Profile 3, Packet Session Status = INACTIVE
>>>>> Inactivity Reason = Normal inactivate state
>>>>> Profile 4, Packet Session Status = INACTIVE
>>>>> Inactivity Reason = Normal inactivate state
>>>>> Profile 5, Packet Session Status = INACTIVE
>>>>> Inactivity Reason = Normal inactivate state
>>>>> Profile 6, Packet Session Status = INACTIVE
>>>>> Inactivity Reason = Normal inactivate state
>>>>> Profile 7, Packet Session Status = INACTIVE
>>>>> Inactivity Reason = Normal inactivate state
>>>>> Profile 8, Packet Session Status = INACTIVE
>>>>> Inactivity Reason = Normal inactivate state
>>>>> Profile 9, Packet Session Status = INACTIVE
>>>>> Inactivity Reason = Normal inactivate state
>>>>> Profile 10, Packet Session Status = INACTIVE
>>>>> Inactivity Reason = Normal inactivate state
>>>>> Profile 11, Packet Session Status = INACTIVE
>>>>> Inactivity Reason = Normal inactivate state
>>>>> Profile 12, Packet Session Status = INACTIVE
>>>>> Inactivity Reason = Normal inactivate state
>>>>> Profile 13, Packet Session Status = INACTIVE
>>>>> Inactivity Reason = Normal inactivate state
>>>>> Profile 14, Packet Session Status = INACTIVE
>>>>> Inactivity Reason = Normal inactivate state
>>>>> Profile 15, Packet Session Status = INACTIVE
>>>>> Inactivity Reason = Normal inactivate state
>>>>> Profile 16, Packet Session Status = INACTIVE
>>>>> Inactivity Reason = Normal inactivate state
>>>>>
>>>>> Network Information
>>>>> ===================
>>>>> Current Service Status = Normal, Service Error = None
>>>>> Current Service = Combined
>>>>> Packet Service = GPRS (Attached)
>>>>> Packet Session Status = Inactive
>>>>> Current Roaming Status = Home
>>>>> Network Selection Mode = Automatic
>>>>> Country = 606, Network = 606 01
>>>>> Mobile Country Code (MCC) = 606
>>>>> Mobile Network Code (MNC) = 1
>>>>> Location Area Code (LAC) = 1
>>>>> Routing Area Code (RAC) = 1
>>>>> Cell ID = 11071
>>>>> Primary Scrambling Code = 0
>>>>> PLMN Selection = Automatic
>>>>> Registered PLMN = Libya Al Madar , Abbreviated = 606 01
>>>>> Service Provider = 606 01
>>>>>
>>>>> Radio Information
>>>>> =================
>>>>> Current Band = GSM 900, Channel Number = 5
>>>>> Current RSSI = -62 dBm
>>>>> Band Selected = Auto
>>>>>
>>>>> Modem Security Information
>>>>> ==========================
>>>>> Card Holder Verification (CHV1) = Disabled
>>>>> SIM Status = OK
>>>>> SIM User Operation Required = None
>>>>> Number of Retries remaining = 3
>>>>>
>>>>>
>>>>> Thanks
>>>>>
>>>>>
>>>>>
>>>>>
>>>>> On Sat, Oct 30, 2010 at 2:42 PM, Bilal Hansrod <
>>>>> bilal.hansrod_at_gmail.com>wrote:
>>>>>
>>>>> > Can you please send the output of *sh cell 0/1/0 all*
>>>>> >
>>>>> >
>>>>> > Bilal
>>>>> >
>>>>> >
>>>>> > On Sat, Oct 30, 2010 at 11:36 PM, muhammad adnan <
>>>>> taurusadnan19_at_gmail.com>wrote:
>>>>> >
>>>>> >> Dear Bilal i configure according to the Cisco Documentation
>>>>> >> and in my mail i pasted show run config...
>>>>> >>
>>>>> >>
>>>>> >>
>>>>> >>
>>>>> http://www.cisco.com/en/US/docs/routers/access/1800/1861/software/feature/guide/mrwlsgsm.html#wp1040391
>>>>> >>
>>>>> >> in my mail i ask that username and password is blank to access the
>>>>> >> internet
>>>>> >> Service provider ask me no authentication username and password
>>>>> blank ("i
>>>>> >> just put Apn in my phone and username and password blank and it
>>>>> works fine
>>>>> >> accessing the internet")
>>>>> >>
>>>>> >> if u need any more information kindly let me know again..
>>>>> >>
>>>>> >> Thanks
>>>>> >> Muhammad Adnan
>>>>> >>
>>>>> >>
>>>>> >>
>>>>> >> On Sat, Oct 30, 2010 at 2:28 PM, Bilal Hansrod <
>>>>> bilal.hansrod_at_gmail.com>wrote:
>>>>> >>
>>>>> >>> Hi Muhammad,
>>>>> >>>
>>>>> >>> I can't see a logical interface created for cell interface where
>>>>> you
>>>>> >>> define your PPP username/password and also the authentication
>>>>> method.
>>>>> >>>
>>>>> >>> An example from my config as below:
>>>>> >>>
>>>>> >>>
>>>>> >>> interface Dialer1
>>>>> >>> ip address negotiated
>>>>> >>> ip virtual-reassembly
>>>>> >>> encapsulation ppp
>>>>> >>> dialer pool 1
>>>>> >>> dialer idle-timeout 0
>>>>> >>> dialer string gsm
>>>>> >>> dialer persistent
>>>>> >>> dialer-group 1
>>>>> >>> no cdp enable
>>>>> >>> ppp authentication chap callin
>>>>> >>> ppp chap hostname XXX
>>>>> >>> ppp chap password YYY
>>>>> >>>
>>>>> >>>
>>>>> >>> Regards,
>>>>> >>>
>>>>> >>> Bilal
>>>>> >>>
>>>>> >>>
>>>>> >>> On Sat, Oct 30, 2010 at 11:05 PM, muhammad adnan <
>>>>> >>> taurusadnan19_at_gmail.com> wrote:
>>>>> >>>
>>>>> >>>> Dear Group members:-
>>>>> >>>> i am trying to configure the
>>>>> 3G-module.i
>>>>> >>>> have inserted my sim card into the HWIC module sim card properly
>>>>> >>>> working in
>>>>> >>>> the phone and i am accessing the internet.
>>>>> >>>> but when i configure HWIC module accordingly i am unable to access
>>>>> the
>>>>> >>>> internet my configration pasted below if any experience person
>>>>> guid me
>>>>> >>>> little.
>>>>> >>>>
>>>>> >>>>
>>>>> >>>> in my phone i just put APN and it work fine without Authentication
>>>>> >>>> *Service
>>>>> >>>> provider ask me* that the *username and password is blank..*
>>>>> >>>>
>>>>> >>>> country Libya
>>>>> >>>> GSM service provider =Almadar
>>>>> >>>> APN or access point name =almadar.net
>>>>> >>>>
>>>>> >>>>
>>>>> >>>>
>>>>> >>>>
>>>>> >>>> *Router#show cellular 0/1/0 profile
>>>>> >>>> Profile 1 = INACTIVE*
>>>>> >>>> --------
>>>>> >>>> PDP Type = IPv4
>>>>> >>>> Access Point Name (APN) = almadar.net
>>>>> >>>> Authentication = None
>>>>> >>>> Username: , Password:
>>>>> >>>>
>>>>> >>>> * - Default profile
>>>>> >>>> *
>>>>> >>>>
>>>>> >>>>
>>>>> --------------------------------------------------------------------------------------
>>>>> >>>> *Router config*:
>>>>> >>>> *
>>>>> >>>> !
>>>>> >>>> !
>>>>> >>>> !
>>>>> >>>> multilink bundle-name authenticated
>>>>> >>>> !
>>>>> >>>> chat-script gsm "" "ATDT*99*1#" TIMEOUT 60 "CONNECT"
>>>>> >>>> !
>>>>> >>>> !
>>>>> >>>> !
>>>>> >>>> !
>>>>> >>>> interface Loopback0
>>>>> >>>> ip address 10.0.0.1 255.255.255.0
>>>>> >>>> !
>>>>> >>>> interface Wlan-GigabitEthernet0/0
>>>>> >>>> description Internal switch interface connecting to the embedded
>>>>> AP
>>>>> >>>> !
>>>>> >>>> interface GigabitEthernet0/0
>>>>> >>>> no ip address
>>>>> >>>> shutdown
>>>>> >>>> duplex auto
>>>>> >>>> speed auto
>>>>> >>>> !
>>>>> >>>> interface wlan-ap0
>>>>> >>>> description Service module interface to manage the embedded AP
>>>>> >>>> no ip address
>>>>> >>>> arp timeout 0
>>>>> >>>> no mop enabled
>>>>> >>>> no mop sysid
>>>>> >>>> !
>>>>> >>>> interface GigabitEthernet0/1
>>>>> >>>> no ip address
>>>>> >>>> shutdown
>>>>> >>>> duplex auto
>>>>> >>>> speed auto
>>>>> >>>> !
>>>>> >>>> interface ATM0/0/0
>>>>> >>>> no ip address
>>>>> >>>> shutdown
>>>>> >>>> no atm ilmi-keepalive
>>>>> >>>> !
>>>>> >>>> interface Cellular0/1/0
>>>>> >>>> ip address negotiated
>>>>> >>>> encapsulation ppp
>>>>> >>>> dialer in-band
>>>>> >>>> dialer idle-timeout 30
>>>>> >>>> dialer string gsm
>>>>> >>>> dialer-group 1
>>>>> >>>> async mode interactive
>>>>> >>>> ppp ipcp dns request
>>>>> >>>> !
>>>>> >>>> interface Vlan1
>>>>> >>>> no ip address
>>>>> >>>> !
>>>>> >>>> ip forward-protocol nd
>>>>> >>>> !
>>>>> >>>> no ip http server
>>>>> >>>> no ip http secure-server
>>>>> >>>> !
>>>>> >>>> ip route 0.0.0.0 0.0.0.0 Cellular0/1/0
>>>>> >>>> !
>>>>> >>>> access-list 1 permit any
>>>>> >>>> dialer-list 1 protocol ip list 1
>>>>> >>>> !
>>>>> >>>> !
>>>>> >>>> !
>>>>> >>>> control-plane
>>>>> >>>> !
>>>>> >>>> !
>>>>> >>>> line con 0
>>>>> >>>> line aux 0
>>>>> >>>> line 0/1/0
>>>>> >>>> exec-timeout 0 0
>>>>> >>>> script dialer gsm
>>>>> >>>> login
>>>>> >>>> modem InOut
>>>>> >>>> no exec
>>>>> >>>> speed 80000
>>>>> >>>> line 67
>>>>> >>>> no activation-character
>>>>> >>>> no exec
>>>>> >>>> transport preferred none
>>>>> >>>> transport input all
>>>>> >>>> transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
>>>>> >>>> line vty 0 4
>>>>> >>>> login
>>>>> >>>> !
>>>>> >>>> scheduler allocate 20000 1000
>>>>> >>>> end*
>>>>> >>>>
>>>>> >>>>
>>>>> >>>>
>>>>> >>>>
>>>>> >>>>
>>>>> >>>>
>>>>> >>>>
>>>>> >>>>
>>>>> >>>> kindly Guid me
>>>>> >>>>
>>>>> >>>>
>>>>> >>>> Blogs and organic groups at http://www.ccie.net
>>>>> >>>>
>>>>> >>>>
>>>>> _______________________________________________________________________
>>>>> >>>> Subscription information may be found at:
>>>>> >>>> http://www.groupstudy.com/list/CCIELab.html
>>>>>
>>>>>
>>>>> Blogs and organic groups at http://www.ccie.net
>>>>>
>>>>> _______________________________________________________________________
>>>>> Subscription information may be found at:
>>>>> http://www.groupstudy.com/list/CCIELab.html
Blogs and organic groups at http://www.ccie.net
Received on Sat Oct 30 2010 - 16:24:32 ART
This archive was generated by hypermail 2.2.0 : Mon Nov 01 2010 - 06:42:06 ART