Re: OT:Voice Gateway & CUCM Problem

hi,

The problem is not with the SP @ all. I can reach the FXO port (analog)
perfectly and from there a tcl script opens which greets you and asks you to
input an internal extension. This is where the problem occurs, the extension
I am dialling is different than the one shown in the Voice Gateway (using
debug voice dial-peer inout). This is the problem I am facing. I am able to
reach the line from outside (mobile) however when asked to put the extension
the router is reading differently or incorrectly than the digits I am
entering on the mobile (digit collection problem) and this leads to an
incorrectly routed call.

Best Regards,

Karim Jamali

On Wed, Feb 17, 2010 at 5:38 PM, <kaelwyoung_at_netscape.net> wrote:

> Karim,
> The Design engineer should instruct the Service Provider to send
> you as many digits ( 3 -10) as you need to make your design work. Typically
> they will send you 3 or 4 digits but you can request that they change their
> swich (DMS-100 ) etc to send you the required digits .
> Karl.
>
>
>
>
>
> -----Original Message-----
> From: Farrukh Haroon <farrukhharoon_at_gmail.com>
> To: karim jamali <karim.jamali_at_gmail.com>
> Cc: mohammed shoeb ahmed <mdshoeb_at_gmail.com>; Cisco certification <
> ccielab_at_groupstudy.com>
> Sent: Tue, Feb 16, 2010 1:14 pm
> Subject: Re: OT:Voice Gateway & CUCM Problem
>
> If you have DID, the provider will only send the last 3 or 4 digits (at
> least this is how STC does it in Saudi), not all 7.
>
> Regards
>
> Farrukh
>
> On Tue, Feb 16, 2010 at 9:11 PM, karim jamali <karim.jamali_at_gmail.com>wrote:
>
> > hi,
> >
> > I have an FXO port connected to PSTN. I am trying to place a call from
> > outside to inside by just dialling into the analog port number, which after
> > a couple of rings opens a secondary tone and then I dial an internal
> > extension. The problem I am facing is related to digit collection; where
> > the
> > digits I am dialling are not always the digits I see in the debug voice
> > dial-peer inout for a reason I can't understand and this leads to the call
> > being unrouted properly. I have tried this without TCL script (by dialling
> > into analog line which opens secondary dial tone) and with TCL script
> > (simple script which just welcomes the caller and asks him to put
> > extension).The weird thing is that it works sometimes & other times it
> > doesn't work.
> >
> > Any help will be much appreciated!
> >
> > Best Regards.
> >
> >
> >
> > On Tue, Feb 16, 2010 at 2:20 PM, mohammed shoeb ahmed <mdshoeb_at_gmail.com
> > >wrote:
> >
> > > Would you please clarify what you are trying to achieve here, if you are
> > > testing auto attendant then "Connection Plar 600" would be needed under
> > your
> > > voice ports.
> > >
> > >
> > >
> > > --
> > > Best Regards,
> > >
> > > Mohammed Shoeb Ahmed
> > >
> > > Sr. Consultant,
> > > CCIE 18379
> > >
> >
> >
> >
> > --
> > KJ
> >
> >
> > Blogs and organic groups at http://www.ccie.net
> >
> > _______________________________________________________________________
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html
>
>
> Blogs and organic groups at http://www.ccie.net
>
> _______________________________________________________________________
> Subscription information may be found at: http://www.groupstudy.com/list/CCIELab.html
>
>
>
>
>
>
>

-- 
KJ
Blogs and organic groups at http://www.ccie.net