Re: OT:Voice Gateway & CUCM Problem

Running configuration;
voice-card 0
 no dspfarm
!
voice-card 1
 no dspfarm
!
voice-card 2
 no dspfarm
!

voice service voip
 allow-connections h323 to h323
 allow-connections h323 to sip
 allow-connections sip to h323
 supplementary-service h450.12
 h323
!

voice class codec 1
 codec preference 1 g711ulaw
 codec preference 2 g711alaw
 codec preference 3 g729r8

!
application
 service aa flash:its-CISCO.2.0.1.0.tcl
  param operator 0
  paramspace english index 1
  paramspace english language en
  paramspace english location flash:
  paramspace english prefix en
  param aa-pilot 600
 !
interface GigabitEthernet0/0
 description $ETH-LAN$$ETH-SW-LAUNCH$$INTF-INFO-GE 0/0$
 ip address 10.10.10.1 255.255.255.248
 shutdown
 duplex auto
 speed auto
 media-type rj45
 negotiation auto
!
interface GigabitEthernet0/1
 description ***** Connected to corpatr_SW *****
 ip address 10.4.1.141 255.255.255.0
 duplex full
 speed 100
 media-type rj45
 negotiation auto
 no keepalive
 h323-gateway voip interface
 h323-gateway voip bind srcaddr 10.4.1.141
!
!
!
control-plane
!
!
!
voice-port 0/0/0
 supervisory disconnect dualtone mid-call
 cptone SA
 timeouts initial 0
 timeouts interdigit 5
 timeouts call-disconnect 0
 timeouts ringing 5
 timeouts wait-release 1
 timing hookflash-out 50
 timing min-ring 100
 description ***<<<General-Line 2784837>>>***
 caller-id enable
!
dial-peer voice 1 voip
 service aa
 destination-pattern 600
 session target ipv4:10.4.1.141
 incoming called-number 600
 dtmf-relay h245-signal h245-alphanumeric
 codec g711ulaw
 no vad
!
dial-peer voice 2 voip
 destination-pattern 5014
 session target ipv4:10.4.1.201
 dtmf-relay h245-alphanumeric
 codec g711ulaw
!
dial-peer voice 3 pots
 incoming called-number .
 port 0/0/0
!
dial-peer voice 4 voip
 destination-pattern 5013
 session target ipv4:10.4.1.201
 dtmf-relay h245-alphanumeric
 codec g711ulaw
 no vad

Debug Output (Working & Not Working)

*Feb 16 07:27:19.243: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:
   Calling Number=, Called Number=, Voice-Interface=0x664C9CFC,
   Timeout=TRUE, Peer Encap Type=ENCAP_VOICE, Peer Search
Type=PEER_TYPE_VOICE,
   Peer Info Type=DIALPEER_INFO_SPEECH
*Feb 16 07:27:19.243: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:
   Result=Success(0) after DP_MATCH_PORT; Incoming Dial-peer=3
*Feb 16 07:27:19.243: //-1/8CB716408011/DPM/dpMatchPeersCore:
   Calling Number=, Called Number=600, Peer Info Type=DIALPEER_INFO_SPEECH
*Feb 16 07:27:19.243: //-1/8CB716408011/DPM/dpMatchPeersCore:
   Match Rule=DP_MATCH_DEST; Called Number=600
*Feb 16 07:27:19.243: //-1/8CB716408011/DPM/dpMatchPeersCore:
   Result=Success(0) after DP_MATCH_DEST
*Feb 16 07:27:19.243: //-1/8CB716408011/DPM/dpMatchPeersMoreArg:
   Result=SUCCESS(0)
   List of Matched Outgoing Dial-peer(s):
     1: Dial-peer Tag=1
*Feb 16 07:27:19.247: //-1/8CB716408011/DPM/dpAssociateIncomingPeerCore:
   Calling Number=, Called Number=600, Voice-Interface=0x0,
   Timeout=TRUE, Peer Encap Type=ENCAP_VOIP, Peer Search
Type=PEER_TYPE_VOICE,
   Peer Info Type=DIALPEER_INFO_SPEECH
*Feb 16 07:27:19.247: //-1/8CB716408011/DPM/dpAssociateIncomingPeerCore:
   Result=Success(0) after DP_MATCH_INCOMING_DNIS; Incoming Dial-peer=1
*Feb 16 07:27:19.247: //-1/8CB716408011/DPM/dpAssociateIncomingPeerCore:
   Calling Number=, Called Number=600, Voice-Interface=0x0,
   Timeout=TRUE, Peer Encap Type=ENCAP_VOIP, Peer Search
Type=PEER_TYPE_VOICE,
   Peer Info Type=DIALPEER_INFO_SPEECH
*Feb 16 07:27:19.247: //-1/8CB716408011/DPM/dpAssociateIncomingPeerCore:
   Result=Success(0) after DP_MATCH_INCOMING_DNIS; Incoming Dial-peer=1
*Feb 16 07:27:24.667: //-1/8CB716408011/DPM/dpMatchPeersCore:
   Calling Number=, Called Number=3, Peer Info Type=DIALPEER_INFO_SPEECH
*Feb 16 07:27:24.667: //-1/8CB716408011/DPM/dpMatchPeersCore:
   Match Rule=DP_MATCH_DEST; Called Number=3
*Feb 16 07:27:24.667: //-1/8CB716408011/DPM/dpMatchPeersCore:
   No Outgoing Dial-peer Is Matched; Result=NO_MATCH(-1)
*Feb 16 07:27:24.667: //-1/8CB716408011/DPM/dpMatchPeersMoreArg:
   Result=NO_MATCH(-1)
*Feb 16 07:27:34.667: //-1/8CB716408011/DPM/dpMatchPeersCore:
   Calling Number=, Called Number=3T, Peer Info Type=DIALPEER_INFO_SPEECH
*Feb 16 07:27:34.667: //-1/8CB716408011/DPM/dpMatchPeersCore:
   Match Rule=DP_MATCH_DEST; Called Number=3T
*Feb 16 07:27:34.667: //-1/8CB716408011/DPM/dpMatchPeersCore:
   No Outgoing Dial-peer Is Matched; Result=NO_MATCH(-1)
*Feb 16 07:27:34.667: //-1/8CB716408011/DPM/dpMatchPeersMoreArg:
   Result=NO_MATCH(-1)
*Feb 16 07:27:39.471: %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on
Giga
bitEthernet0/1 (not half duplex), with BMB-KSA-SW1 FastEthernet0/24 (half
duplex
).
*Feb 16 07:27:43.227: //-1/8CB716408011/DPM/dpMatchPeersCore:
   Calling Number=, Called Number=1, Peer Info Type=DIALPEER_INFO_SPEECH
*Feb 16 07:27:43.227: //-1/8CB716408011/DPM/dpMatchPeersCore:
   Match Rule=DP_MATCH_DEST; Called Number=1
*Feb 16 07:27:43.227: //-1/8CB716408011/DPM/dpMatchPeersCore:
   No Outgoing Dial-peer Is Matched; Result=NO_MATCH(-1)
*Feb 16 07:27:43.227: //-1/8CB716408011/DPM/dpMatchPeersMoreArg:
   Result=NO_MATCH(-1)
*Feb 16 07:27:53.227: //-1/8CB716408011/DPM/dpMatchPeersCore:
   Calling Number=, Called Number=1T, Peer Info Type=DIALPEER_INFO_SPEECH
*Feb 16 07:27:53.227: //-1/8CB716408011/DPM/dpMatchPeersCore:
   Match Rule=DP_MATCH_DEST; Called Number=1T
*Feb 16 07:27:53.227: //-1/8CB716408011/DPM/dpMatchPeersCore:
   No Outgoing Dial-peer Is Matched; Result=NO_MATCH(-1)
*Feb 16 07:27:53.227: //-1/8CB716408011/DPM/dpMatchPeersMoreArg:
   Result=NO_MATCH(-1)

=====================================================================================================
Another Debug Working
Feb 16 07:25:54.615: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:
  Calling Number=, Called Number=, Voice-Interface=0x664C9CFC,
  Timeout=TRUE, Peer Encap Type=ENCAP_VOICE, Peer Search
Type=PEER_TYPE_VOICE
  Peer Info Type=DIALPEER_INFO_SPEECH
Feb 16 07:25:54.615: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:
  Result=Success(0) after DP_MATCH_PORT; Incoming Dial-peer=3
Feb 16 07:25:54.619: //-1/5A45E09D800B/DPM/dpMatchPeersCore:
  Calling Number=, Called Number=600, Peer Info Type=DIALPEER_INFO_SPEECH
Feb 16 07:25:54.619: //-1/5A45E09D800B/DPM/dpMatchPeersCore:
  Match Rule=DP_MATCH_DEST; Called Number=600
Feb 16 07:25:54.619: //-1/5A45E09D800B/DPM/dpMatchPeersCore:
  Result=Success(0) after DP_MATCH_DEST
Feb 16 07:25:54.619: //-1/5A45E09D800B/DPM/dpMatchPeersMoreArg:
  Result=SUCCESS(0)
  List of Matched Outgoing Dial-peer(s):
    1: Dial-peer Tag=1
Feb 16 07:25:54.623: //-1/5A45E09D800B/DPM/dpAssociateIncomingPeerCore:
  Calling Number=, Called Number=600, Voice-Interface=0x0,
  Timeout=TRUE, Peer Encap Type=ENCAP_VOIP, Peer Search
Type=PEER_TYPE_VOICE,
  Peer Info Type=DIALPEER_INFO_SPEECH
Feb 16 07:25:54.623: //-1/5A45E09D800B/DPM/dpAssociateIncomingPeerCore:
  Result=Success(0) after DP_MATCH_INCOMING_DNIS; Incoming Dial-peer=1
PMG-VGW1#terminal monitor
Feb 16 07:25:54.623: //-1/5A45E09D800B/DPM/dpAssociateIncomingPeerCore:
  Calling Number=, Called Number=600, Voice-Interface=0x0,
  Timeout=TRUE, Peer Encap Type=ENCAP_VOIP, Peer Search
Type=PEER_TYPE_VOICE,
  Peer Info Type=DIALPEER_INFO_SPEECH
Feb 16 07:25:54.623: //-1/5A45E09D800B/DPM/dpAssociateIncomingPeerCore:
  Result=Success(0) after DP_MATCH_INCOMING_DNIS; Incoming Dial-peer=1
PMG-VGW1#
Feb 16 07:26:04.803: //-1/5A45E09D800B/DPM/dpMatchPeersCore:
  Calling Number=, Called Number=5, Peer Info Type=DIALPEER_INFO_SPEECH
Feb 16 07:26:04.803: //-1/5A45E09D800B/DPM/dpMatchPeersCore:
  Match Rule=DP_MATCH_DEST; Called Number=5
Feb 16 07:26:04.803: //-1/5A45E09D800B/DPM/dpMatchPeersCore:
  Result=Partial Matches(1) after DP_MATCH_DEST
Feb 16 07:26:04.803: //-1/5A45E09D800B/DPM/dpMatchPeersMoreArg:
  Result=MORE_DIGITS_NEEDED(1)
Feb 16 07:26:06.123: //-1/5A45E09D800B/DPM/dpMatchPeersCore:
  Calling Number=, Called Number=50, Peer Info Type=DIALPEER_INFO_SPEECH
Feb 16 07:26:06.123: //-1/5A45E09D800B/DPM/dpMatchPeersCore:
  Match Rule=DP_MATCH_DEST; Called Number=50
Feb 16 07:26:06.123: //-1/5A45E09D800B/DPM/dpMatchPeersCore:
  Result=Partial Matches(1) after DP_MATCH_DEST
Feb 16 07:26:06.123: //-1/5A45E09D800B/DPM/dpMatchPeersMoreArg:
  Result=MORE_DIGITS_NEEDED(1)
Feb 16 07:26:06.775: //-1/5A45E09D800B/DPM/dpMatchPeersCore:
  Calling Number=, Called Number=501, Peer Info Type=DIALPEER_INFO_SPEECH
Feb 16 07:26:06.775: //-1/5A45E09D800B/DPM/dpMatchPeersCore:
  Match Rule=DP_MATCH_DEST; Called Number=501
Feb 16 07:26:06.775: //-1/5A45E09D800B/DPM/dpMatchPeersCore:
  Result=Partial Matches(1) after DP_MATCH_DEST
Feb 16 07:26:06.775: //-1/5A45E09D800B/DPM/dpMatchPeersMoreArg:
  Result=MORE_DIGITS_NEEDED(1)
Feb 16 07:26:07.395: //-1/5A45E09D800B/DPM/dpMatchPeersCore:
  Calling Number=, Called Number=5013, Peer Info Type=DIALPEER_INFO_SPEECH
Feb 16 07:26:07.395: //-1/5A45E09D800B/DPM/dpMatchPeersCore:
  Match Rule=DP_MATCH_DEST; Called Number=5013
Feb 16 07:26:07.395: //-1/5A45E09D800B/DPM/dpMatchPeersCore:
  Result=Success(0) after DP_MATCH_DEST
Feb 16 07:26:07.395: //-1/5A45E09D800B/DPM/dpMatchPeersMoreArg:
  Result=SUCCESS(0)
  List of Matched Outgoing Dial-peer(s):
    1: Dial-peer Tag=4
Feb 16 07:26:07.395: //-1/5A45E09D800B/DPM/dpMatchPeersCore:
  Calling Number=, Called Number=5013, Peer Info Type=DIALPEER_INFO_SPEECH
Feb 16 07:26:07.395: //-1/5A45E09D800B/DPM/dpMatchPeersCore:
  Match Rule=DP_MATCH_DEST; Called Number=5013
Feb 16 07:26:07.395: //-1/5A45E09D800B/DPM/dpMatchPeersCore:
  Result=Success(0) after DP_MATCH_DEST
Feb 16 07:26:07.395: //-1/5A45E09D800B/DPM/dpMatchPeersMoreArg:
  Result=SUCCESS(0)
  List of Matched Outgoing Dial-peer(s):
    1: Dial-peer Tag=4

BR

-- 
KJ
On Wed, Feb 17, 2010 at 5:55 PM, <kaelwyoung_at_netscape.net> wrote:
> Karim,
>             Please send me that gateway config .
>                             Karl.
>
>
>
>
>
> -----Original Message-----
> From: karim jamali <karim.jamali_at_gmail.com>
> To: kaelwyoung_at_netscape.net; Cisco certification <ccielab_at_groupstudy.com>
> Sent: Wed, Feb 17, 2010 9:48 am
> Subject: Re: OT:Voice Gateway & CUCM Problem
>
> hi,
>
> The problem is not with the SP @ all. I can reach the FXO port (analog)
> perfectly and from there a tcl script opens which greets you and asks you to
> input an internal extension. This is where the problem occurs, the extension
> I am dialling is different than the one shown in the Voice Gateway (using
> debug voice dial-peer inout). This is the problem I am facing. I am able to
> reach the line from outside (mobile) however when asked to put the extension
> the router is reading differently or incorrectly than the digits I am
> entering on the mobile (digit collection problem) and this leads to an
> incorrectly routed call.
>
> Best Regards,
>
> Karim Jamali
>
> On Wed, Feb 17, 2010 at 5:38 PM, <kaelwyoung_at_netscape.net> wrote:
>
> > Karim,
> >            The Design engineer should instruct the Service Provider to send
> > you as many digits ( 3 -10) as you need to make your design work. Typically
> > they will send you 3 or 4 digits but you can request that they change their
> > swich (DMS-100 ) etc to send you the required digits .
> >                                                           Karl.
> >
> >
> >
> >
> >
> > -----Original Message-----
> > From: Farrukh Haroon <farrukhharoon_at_gmail.com>
> > To: karim jamali <karim.jamali_at_gmail.com>
> > Cc: mohammed shoeb ahmed <mdshoeb_at_gmail.com>; Cisco certification <
> > ccielab_at_groupstudy.com>
> > Sent: Tue, Feb 16, 2010 1:14 pm
> > Subject: Re: OT:Voice Gateway & CUCM Problem
> >
> > If you have DID, the provider will only send the last 3 or 4 digits (at
> > least this is how STC does it in Saudi), not all 7.
> >
> > Regards
> >
> > Farrukh
> >
> > On Tue, Feb 16, 2010 at 9:11 PM, karim jamali <karim.jamali_at_gmail.com>wrote:
> >
> > > hi,
> > >
> > > I have an FXO port connected to PSTN. I am trying to place a call from
> > > outside to inside by just dialling into the analog port number, which after
> > > a couple of rings opens a secondary tone and then I dial an internal
> > > extension. The problem I am facing is related to digit collection; where
> > > the
> > > digits I am dialling are not always the digits I see in the debug voice
> > > dial-peer inout for a reason I can't understand and this leads to the call
> > > being unrouted properly. I have tried this without TCL script (by dialling
> > > into analog line which opens secondary dial tone) and with TCL script
> > > (simple script which just welcomes the caller and asks him to put
> > > extension).The weird thing is that it works sometimes & other times it
> > > doesn't work.
> > >
> > > Any help will be much appreciated!
> > >
> > > Best Regards.
> > >
> > >
> > >
> > > On Tue, Feb 16, 2010 at 2:20 PM, mohammed shoeb ahmed <mdshoeb_at_gmail.com
> > > >wrote:
> > >
> > > >  Would you please clarify what you are trying to achieve here, if you are
> > > > testing auto attendant then "Connection Plar 600" would be needed under
> > > your
> > > > voice ports.
> > > >
> > > >
> > > >
> > > > --
> > > > Best Regards,
> > > >
> > > > Mohammed Shoeb Ahmed
> > > >
> > > > Sr. Consultant,
> > > > CCIE 18379
> > > >
> > >
> > >
> > >
> > > --
> > > KJ
> > >
> > >
> > > Blogs and organic groups at http://www.ccie.net
> > >
> > > _______________________________________________________________________
> > > Subscription information may be found at:
> > > http://www.groupstudy.com/list/CCIELab.html
> >
> >
> > Blogs and organic groups at http://www.ccie.net
> >
> > _______________________________________________________________________
> > Subscription information may be found at: http://www.groupstudy.com/list/CCIELab.html
> >
> >
> >
> >
> >
> >
> >
>
>
> --
> KJ
>
>
> Blogs and organic groups at http://www.ccie.net
>
> _______________________________________________________________________
> Subscription information may be found at: http://www.groupstudy.com/list/CCIELab.html
>
>
>
>
>
>
>
-- 
KJ
Blogs and organic groups at http://www.ccie.net