Re: leased line with G703 module using router 2851 and 2801

yes that is possible. Your lease line provider should map your individual 2
megs timeslots to all remote site using a MUX.
In central site u can just use one interface with frame-relay
point-to-multipoint subinterface.

On Wed, Jul 15, 2009 at 8:02 PM, Mohammed Naviwala <monavy_at_gmail.com> wrote:

> well if that is the requirement, you were better off with the
> MPLS........leased lines dont work that way....
>
>
> On Wed, Jul 15, 2009 at 1:37 PM, erwin wijaya <erwinem.wijaya_at_gmail.com>wrote:
>
>> Hi again,
>>
>> Is it possible at central site only using 1 router and 1 vwic G703? coz,
>> all branch office connected leased line to central site. so we just adding
>> 1 card G703 per branch?
>>
>> thanks again..
>> regards-Erwin
>>
>>
>>
>> Radioactive Frog wrote:
>>
>>> u only need 1 routerat the central site wiht 3 serial or E1 interface
>>> (depends where E1 line terminates). If its close to (within 120
>>> meters) PDH/SDH MuX use E1 else u may need to use a e1 extender
>>> convertor.
>>>
>>>
>>> On 7/7/09, erwinem wijaya <erwinem.wijaya_at_gmail.com> wrote:
>>>
>>>
>>>> Hi all,
>>>> another questions, for example i need to connecting office B to A, also
>>>> ofice C to A, and office D to A. office A is a central office. do wee
>>>> need 3
>>>> router at office A or we just need 1 router at office A if we'll using
>>>> leased line. Today we using 1 router for 3 branch office with MPLS.
>>>>
>>>> thanks for any helps.
>>>>
>>>> ----- Original Message -----
>>>> From: Radioactive Frog
>>>> To: erwin wijaya
>>>> Cc: ccielab_at_groupstudy.com
>>>> Sent: Tuesday, June 30, 2009 8:39 PM
>>>> Subject: Re: leased line with G703 module using router 2851 and 2801
>>>>
>>>>
>>>> Hi Erwin,It's damn easy!controller E1 2/0channel-group 0 unframedafter
>>>> issuing above command the router creates a logical serial interface
>>>> where
>>>> you can put your WAN ip, just like you've seen serial port.assign ip
>>>> here
>>>> for wan side of thigns.
>>>> interface Serial2/0:0ip address 1.1.1.1 255.255.255.0verify by using
>>>> 'show
>>>> controller e1 1/0 and show inter serial2/0:0"HTH-frog
>>>>
>>>> On Tue, Jun 30, 2009 at 5:33 PM, erwin wijaya <
>>>> erwinem.wijaya_at_gmail.com>
>>>> wrote:
>>>>
>>>> dear all,
>>>> how to configure my router when i need to connecting my office
>>>> (router
>>>> 2851) with branch office (router 2801) using G703 module. We are using
>>>> leased line conection to connecting both office. Also we'll use to send
>>>> data
>>>> and voice..present we using MPLS tech to connecting both office. Is it
>>>> the
>>>> same way?
>>>>
>>>> thanks alot for any helps.
>>>> regards - erwin
>>>>
>>>>
>>>> Blogs and organic groups at http://www.ccie.net
>>>>
>>>>
>>>> _______________________________________________________________________
>>>> Subscription information may be found at:
>>>> http://www.groupstudy.com/list/CCIELab.html
>>>>
>>>
>>
>> Blogs and organic groups at http://www.ccie.net
>>
>> _______________________________________________________________________
>> Subscription information may be found at:
>> http://www.groupstudy.com/list/CCIELab.html
>>
>>
>>
>>
>>
>>
>>
>>
>
>
> --
> Best Regards
>
> Mohammed Abdul Razzaq
>
>
> If you are not small enough to loose, you are not big enough to win..

Blogs and organic groups at http://www.ccie.net
Received on Thu Jul 16 2009 - 17:10:08 ART