Re: RMON Error

Cool. Just remember those names are sensitive.
And if in doubt you can do "show snmp mib" to see possible names, it's very
long list :)

On Mon, May 18, 2009 at 9:08 AM, Splinter <splinter330_at_gmail.com> wrote:

> Bryan thanx,
>
> It works
>
> regards
>
> Splinter
>
>
> On Mon, May 18, 2009 at 5:02 PM, Bryan Bartik <bbartik_at_ipexpert.com>wrote:
>
>> use a lower case i.
>>
>> ifOutQLen.4
>>
>>
>> On Mon, May 18, 2009 at 8:56 AM, Splinter <splinter330_at_gmail.com> wrote:
>>
>>> Bryan,
>>>
>>> not working this is the error: Unknown object: IfOutQLen.4
>>>
>>> Splinter
>>>
>>>
>>> On Mon, May 18, 2009 at 4:52 PM, Bryan Bartik <bbartik_at_ipexpert.com>wrote:
>>>
>>>> Splinter,
>>>>
>>>> You have to specify the interface index after ifOutQLen. If your s2/0 is
>>>> interface 4 then:
>>>>
>>>> rmon alarm 1 ifOutQLen.4 30 absolute rising-threshold 40 1
>>>> falling-threshold 0 2
>>>>
>>>> Bryan Bartik
>>>> CCIE #23707 (R&S), CCNP
>>>> Sr. Support Engineer - IPexpert, Inc.
>>>> URL: http://www.IPexpert.com
>>>>
>>>>
>>>>
>>>> On Mon, May 18, 2009 at 8:38 AM, Splinter <splinter330_at_gmail.com>wrote:
>>>>
>>>>> Hello Sir,
>>>>>
>>>>> I am getting an "Alarm creation failure"
>>>>>
>>>>> R6#sh snmp mib ifmib ifindex
>>>>> FastEthernet0/0: Ifindex = 2
>>>>> Loopback0: Ifindex = 13
>>>>> Null0: Ifindex = 8
>>>>> Serial2/0: Ifindex = 4
>>>>> Virtual-Access2: Ifindex = 25
>>>>> FastEthernet0/1: Ifindex = 3
>>>>> Serial2/1: Ifindex = 5
>>>>> Serial2/2: Ifindex = 6
>>>>> Serial2/3: Ifindex = 7
>>>>> FastEthernet0/0.26-mpls layer: Ifindex = 16
>>>>> FastEthernet0/0.67-mpls layer: Ifindex = 18
>>>>> FastEthernet0/0.26-802.1Q vLAN subif: Ifindex = 15
>>>>> FastEthernet0/0.67-802.1Q vLAN subif: Ifindex = 17
>>>>>
>>>>> Splinter
>>>>>
>>>>>
>>>>> On Mon, May 18, 2009 at 4:31 PM, Shaughn Smith <
>>>>> Shaughn.Smith_at_mtnbusiness.co.za> wrote:
>>>>>
>>>>> > Do this, to get the specific interface mib
>>>>> >
>>>>> > Test#sh snmp mib ifmib ifindex
>>>>> > Async0/0/0: Ifindex = 5
>>>>> > FastEthernet0/0: Ifindex = 1
>>>>> > Loopback0: Ifindex = 7
>>>>> > Null0: Ifindex = 4
>>>>> > Serial0/0/0: Ifindex = 3
>>>>> > Loopback1: Ifindex = 8
>>>>> > FastEthernet0/1: Ifindex = 2
>>>>> > Serial0/0/0.101: Ifindex = 6
>>>>> >
>>>>> > Then this
>>>>> >
>>>>> > rmon alarm 1 ifEntry.3 (<------ from step 1, ie serial0/0) 30
>>>>> absolute
>>>>> > rising threshold 40 1 falling-threshold 0
>>>>> > 2
>>>>> >
>>>>> >
>>>>> >
>>>>> > -----Original Message-----
>>>>> > From: nobody_at_groupstudy.com [mailto:nobody_at_groupstudy.com] On Behalf
>>>>> Of
>>>>> > Splinter
>>>>> > Sent: Monday, May 18, 2009 3:58 PM
>>>>> > To: ccielab_at_groupstudy.com
>>>>> > Subject: RMON Error
>>>>> >
>>>>> > Hello,
>>>>> >
>>>>> > when I configure my rmon alarm i get the following error:
>>>>> >
>>>>> > Unknown object: ifOutQlen
>>>>> >
>>>>> > where am i going wrong?
>>>>> >
>>>>> > here is my config:
>>>>> >
>>>>> > snmp-server ifindex persist
>>>>> > snmp-server community public
>>>>> > snmp-server enable traps syslog
>>>>> >
>>>>> > rmon event 1 log trap public description "serial 2/0 output queue
>>>>> full"
>>>>> > owner cisco
>>>>> > rmon event 2 log trap public description "serial 2/0 output queue OK"
>>>>> owner
>>>>> > cisco
>>>>> > rmon alarm 1 ifOutQlen 30 absolute rising threshold 40 1
>>>>> falling-threshold
>>>>> > 0
>>>>> > 2 <= "this is were i am getting the error"
>>>>> >
>>>>> > the sampling MIB vlaue is ifEntry.21
>>>>> >
>>>>> > please help failing to get the correct IfEntry.
>>>>> >
>>>>> > Splinter
>>>>> >
>>>>> >
>>>>> > Blogs and organic groups at http://www.ccie.net
>>>>> >
>>>>> >
>>>>> _______________________________________________________________________
>>>>> > Subscription information may be found at:
>>>>> > http://www.groupstudy.com/list/CCIELab.html
>>>>>
>>>>>
>>>>> Blogs and organic groups at http://www.ccie.net
>>>>>
>>>>> _______________________________________________________________________
>>>>> Subscription information may be found at:
>>>>> http://www.groupstudy.com/list/CCIELab.html
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>
>>>>
>>>>
>>>> --
>>>>
>>>>
>>>
>>
>>
>> --
>> Bryan Bartik
>> CCIE #23707 (R&S), CCNP
>> Sr. Support Engineer - IPexpert, Inc.
>> URL: http://www.IPexpert.com
>>
>
>

-- 
Bryan Bartik
CCIE #23707 (R&S), CCNP
Sr. Support Engineer - IPexpert, Inc.
URL: http://www.IPexpert.com
Blogs and organic groups at http://www.ccie.net