Re: RMON Error

Bryan thanx,

It works

regards

Splinter

On Mon, May 18, 2009 at 5:02 PM, Bryan Bartik <bbartik_at_ipexpert.com> wrote:

> use a lower case i.
>
> ifOutQLen.4
>
>
> On Mon, May 18, 2009 at 8:56 AM, Splinter <splinter330_at_gmail.com> wrote:
>
>> Bryan,
>>
>> not working this is the error: Unknown object: IfOutQLen.4
>>
>> Splinter
>>
>>
>> On Mon, May 18, 2009 at 4:52 PM, Bryan Bartik <bbartik_at_ipexpert.com>wrote:
>>
>>> Splinter,
>>>
>>> You have to specify the interface index after ifOutQLen. If your s2/0 is
>>> interface 4 then:
>>>
>>> rmon alarm 1 ifOutQLen.4 30 absolute rising-threshold 40 1
>>> falling-threshold 0 2
>>>
>>> Bryan Bartik
>>> CCIE #23707 (R&S), CCNP
>>> Sr. Support Engineer - IPexpert, Inc.
>>> URL: http://www.IPexpert.com
>>>
>>>
>>>
>>> On Mon, May 18, 2009 at 8:38 AM, Splinter <splinter330_at_gmail.com> wrote:
>>>
>>>> Hello Sir,
>>>>
>>>> I am getting an "Alarm creation failure"
>>>>
>>>> R6#sh snmp mib ifmib ifindex
>>>> FastEthernet0/0: Ifindex = 2
>>>> Loopback0: Ifindex = 13
>>>> Null0: Ifindex = 8
>>>> Serial2/0: Ifindex = 4
>>>> Virtual-Access2: Ifindex = 25
>>>> FastEthernet0/1: Ifindex = 3
>>>> Serial2/1: Ifindex = 5
>>>> Serial2/2: Ifindex = 6
>>>> Serial2/3: Ifindex = 7
>>>> FastEthernet0/0.26-mpls layer: Ifindex = 16
>>>> FastEthernet0/0.67-mpls layer: Ifindex = 18
>>>> FastEthernet0/0.26-802.1Q vLAN subif: Ifindex = 15
>>>> FastEthernet0/0.67-802.1Q vLAN subif: Ifindex = 17
>>>>
>>>> Splinter
>>>>
>>>>
>>>> On Mon, May 18, 2009 at 4:31 PM, Shaughn Smith <
>>>> Shaughn.Smith_at_mtnbusiness.co.za> wrote:
>>>>
>>>> > Do this, to get the specific interface mib
>>>> >
>>>> > Test#sh snmp mib ifmib ifindex
>>>> > Async0/0/0: Ifindex = 5
>>>> > FastEthernet0/0: Ifindex = 1
>>>> > Loopback0: Ifindex = 7
>>>> > Null0: Ifindex = 4
>>>> > Serial0/0/0: Ifindex = 3
>>>> > Loopback1: Ifindex = 8
>>>> > FastEthernet0/1: Ifindex = 2
>>>> > Serial0/0/0.101: Ifindex = 6
>>>> >
>>>> > Then this
>>>> >
>>>> > rmon alarm 1 ifEntry.3 (<------ from step 1, ie serial0/0) 30 absolute
>>>> > rising threshold 40 1 falling-threshold 0
>>>> > 2
>>>> >
>>>> >
>>>> >
>>>> > -----Original Message-----
>>>> > From: nobody_at_groupstudy.com [mailto:nobody_at_groupstudy.com] On Behalf
>>>> Of
>>>> > Splinter
>>>> > Sent: Monday, May 18, 2009 3:58 PM
>>>> > To: ccielab_at_groupstudy.com
>>>> > Subject: RMON Error
>>>> >
>>>> > Hello,
>>>> >
>>>> > when I configure my rmon alarm i get the following error:
>>>> >
>>>> > Unknown object: ifOutQlen
>>>> >
>>>> > where am i going wrong?
>>>> >
>>>> > here is my config:
>>>> >
>>>> > snmp-server ifindex persist
>>>> > snmp-server community public
>>>> > snmp-server enable traps syslog
>>>> >
>>>> > rmon event 1 log trap public description "serial 2/0 output queue
>>>> full"
>>>> > owner cisco
>>>> > rmon event 2 log trap public description "serial 2/0 output queue OK"
>>>> owner
>>>> > cisco
>>>> > rmon alarm 1 ifOutQlen 30 absolute rising threshold 40 1
>>>> falling-threshold
>>>> > 0
>>>> > 2 <= "this is were i am getting the error"
>>>> >
>>>> > the sampling MIB vlaue is ifEntry.21
>>>> >
>>>> > please help failing to get the correct IfEntry.
>>>> >
>>>> > Splinter
>>>> >
>>>> >
>>>> > Blogs and organic groups at http://www.ccie.net
>>>> >
>>>> >
>>>> _______________________________________________________________________
>>>> > Subscription information may be found at:
>>>> > http://www.groupstudy.com/list/CCIELab.html
>>>>
>>>>
>>>> Blogs and organic groups at http://www.ccie.net
>>>>
>>>> _______________________________________________________________________
>>>> Subscription information may be found at:
>>>> http://www.groupstudy.com/list/CCIELab.html
>>>>
>>>>
>>>>
>>>>
>>>>
>>>>
>>>>
>>>>
>>>
>>>
>>> --
>>>
>>>
>>
>
>
> --
> Bryan Bartik
> CCIE #23707 (R&S), CCNP
> Sr. Support Engineer - IPexpert, Inc.
> URL: http://www.IPexpert.com

Blogs and organic groups at http://www.ccie.net
Received on Mon May 18 2009 - 17:08:22 ART