Re: RMON Error

Splinter,

You have to specify the interface index after ifOutQLen. If your s2/0 is
interface 4 then:

rmon alarm 1 ifOutQLen.4 30 absolute rising-threshold 40 1 falling-threshold
0 2

Bryan Bartik
CCIE #23707 (R&S), CCNP
Sr. Support Engineer - IPexpert, Inc.
URL: http://www.IPexpert.com

On Mon, May 18, 2009 at 8:38 AM, Splinter <splinter330_at_gmail.com> wrote:

> Hello Sir,
>
> I am getting an "Alarm creation failure"
>
> R6#sh snmp mib ifmib ifindex
> FastEthernet0/0: Ifindex = 2
> Loopback0: Ifindex = 13
> Null0: Ifindex = 8
> Serial2/0: Ifindex = 4
> Virtual-Access2: Ifindex = 25
> FastEthernet0/1: Ifindex = 3
> Serial2/1: Ifindex = 5
> Serial2/2: Ifindex = 6
> Serial2/3: Ifindex = 7
> FastEthernet0/0.26-mpls layer: Ifindex = 16
> FastEthernet0/0.67-mpls layer: Ifindex = 18
> FastEthernet0/0.26-802.1Q vLAN subif: Ifindex = 15
> FastEthernet0/0.67-802.1Q vLAN subif: Ifindex = 17
>
> Splinter
>
>
> On Mon, May 18, 2009 at 4:31 PM, Shaughn Smith <
> Shaughn.Smith_at_mtnbusiness.co.za> wrote:
>
> > Do this, to get the specific interface mib
> >
> > Test#sh snmp mib ifmib ifindex
> > Async0/0/0: Ifindex = 5
> > FastEthernet0/0: Ifindex = 1
> > Loopback0: Ifindex = 7
> > Null0: Ifindex = 4
> > Serial0/0/0: Ifindex = 3
> > Loopback1: Ifindex = 8
> > FastEthernet0/1: Ifindex = 2
> > Serial0/0/0.101: Ifindex = 6
> >
> > Then this
> >
> > rmon alarm 1 ifEntry.3 (<------ from step 1, ie serial0/0) 30 absolute
> > rising threshold 40 1 falling-threshold 0
> > 2
> >
> >
> >
> > -----Original Message-----
> > From: nobody_at_groupstudy.com [mailto:nobody_at_groupstudy.com] On Behalf Of
> > Splinter
> > Sent: Monday, May 18, 2009 3:58 PM
> > To: ccielab_at_groupstudy.com
> > Subject: RMON Error
> >
> > Hello,
> >
> > when I configure my rmon alarm i get the following error:
> >
> > Unknown object: ifOutQlen
> >
> > where am i going wrong?
> >
> > here is my config:
> >
> > snmp-server ifindex persist
> > snmp-server community public
> > snmp-server enable traps syslog
> >
> > rmon event 1 log trap public description "serial 2/0 output queue full"
> > owner cisco
> > rmon event 2 log trap public description "serial 2/0 output queue OK"
> owner
> > cisco
> > rmon alarm 1 ifOutQlen 30 absolute rising threshold 40 1
> falling-threshold
> > 0
> > 2 <= "this is were i am getting the error"
> >
> > the sampling MIB vlaue is ifEntry.21
> >
> > please help failing to get the correct IfEntry.
> >
> > Splinter
> >
> >
> > Blogs and organic groups at http://www.ccie.net
> >
> > _______________________________________________________________________
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html
>
>
> Blogs and organic groups at http://www.ccie.net
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
>
>
>
>
>
>
>

--
Blogs and organic groups at http://www.ccie.net