Re: Dynamips Issue

Thanks All for your help now its working fine I just change the idlepc
value and now it much better 30 to 40 % only

Thanks.

On Mon, May 11, 2009 at 7:39 PM, marish shah <contactmarish_at_gmail.com>wrote:

> Its Quad Core
>
> On Mon, May 11, 2009 at 7:31 PM, Divin Mathew John <divinjohn_at_gmail.com>wrote:
>
>> whts "Quote to Core." ??
>>
>> u mean Quad Core? or Core 2 Duo?
>> Thanking You
>>
>> Yours Sincerely
>>
>> Divin Mathew John
>> divinjohn_at_gmail.com
>> divin_at_dide3d.com
>> http://www.dide3d.com
>> +91 9945430983
>> +91 9846697191
>> +974 5008916
>> PGP PUBLIC KEY BLOCK @ http://www.dide3d.com/divin_Public_PGP_key.txt
>> Sent from Bangalore, KA, India
>>
>>
>> On Mon, May 11, 2009 at 8:33 PM, Peter Kurdziel <usaccie_at_gmail.com>
>> wrote:
>> > Your Idlepc values need to be tweaked. It takes some time to find a
>> good
>> > one for your pc.
>> >
>> > Try http://www.gns3.net/ It's much easier to work with.
>> >
>> > http://www.gns3.net/documentation
>> >
>> > On Mon, May 11, 2009 at 10:38 AM, Ravi Singh <way2ccie_at_googlemail.com
>> >wrote:
>> >
>> >> Hi Marish,
>> >>
>> >> 1) As Welly said, the already configured idlepc values in your
>> >> topology will not work. You need to find one that suits your system .
>> >>
>> >> 2) When you find out an idlepc value check how much is your cpu usage
>> >> when you have only a couple of routers started. If it is still high
>> >> ,say above 40 - 50% , you do not have the optimum idlepc value set up.
>> >> You will have to play around a bit to find the best idlepc value.
>> >>
>> >> 3) do not start all the routers together. Start 2 or 3 , telnet into
>> >> them , then then next 2 or 3 and then telnet. Your cpu utilization
>> >> increases when the routers are getting started and it decreases when
>> >> you telnet and get to the router> prompt.
>> >>
>> >> And yes,I think a loop in your topology will increase your cpu
>> utilization
>> >> .
>> >>
>> >> P.S - do read the dynamips/dynagen tutorial . It does help a lot
>> >>
>> >> HTH,
>> >> Ravi
>> >>
>> >> On Mon, May 11, 2009 at 2:56 PM, marish shah <contactmarish_at_gmail.com>
>> >> wrote:
>> >> > Hi Experts,
>> >> > I'm facing some problem with my dynamips.(Slowness
>> >> > problem).During Using dynamips my CPU Usage always remain 100% and
>> make
>> >> my
>> >> > work very slow.I have CPU with this Specifcations.
>> >> > Ram = 6 GB
>> >> > Procssor = 2.6 Quote to Core.
>> >> > Window = XP
>> >> >
>> >> > and on this PC I don't have any software install no Anti Virus.
>> >> > I'm using IEW dynamips topolgy which already configured with idle pc
>> >> value
>> >> > So my Q is still I need to put any thing to reduse my CPU utlization.
>> >> > And one Q more that when where there is loop in my topology it will
>> make
>> >> my
>> >> > dyamips slow also ?
>> >> >
>> >> > Thanks.
>> >> >
>> >> >
>> >> > Blogs and organic groups at http://www.ccie.net
>> >> >
>> >> >
>> _______________________________________________________________________
>> >> > Subscription information may be found at:
>> >> > http://www.groupstudy.com/list/CCIELab.html
>> >>
>> >>
>> >> Blogs and organic groups at http://www.ccie.net
>> >>
>> >> _______________________________________________________________________
>> >> Subscription information may be found at:
>> >> http://www.groupstudy.com/list/CCIELab.html
>> >>
>> >>
>> >>
>> >>
>> >>
>> >>
>> >>
>> >>
>> >
>> >
>> > --
>> > Regards,
>> > Peter Kurdziel
>> >
>> >
>> > Blogs and organic groups at http://www.ccie.net
>> >
>> > _______________________________________________________________________
>> > Subscription information may be found at:
>> > http://www.groupstudy.com/list/CCIELab.html

Blogs and organic groups at http://www.ccie.net
Received on Mon May 11 2009 - 21:18:45 ART