Re: Dynamips Issue

Its Quad Core

On Mon, May 11, 2009 at 7:31 PM, Divin Mathew John <divinjohn_at_gmail.com>wrote:

> whts "Quote to Core." ??
>
> u mean Quad Core? or Core 2 Duo?
> Thanking You
>
> Yours Sincerely
>
> Divin Mathew John
> divinjohn_at_gmail.com
> divin_at_dide3d.com
> http://www.dide3d.com
> +91 9945430983
> +91 9846697191
> +974 5008916
> PGP PUBLIC KEY BLOCK @ http://www.dide3d.com/divin_Public_PGP_key.txt
> Sent from Bangalore, KA, India
>
>
> On Mon, May 11, 2009 at 8:33 PM, Peter Kurdziel <usaccie_at_gmail.com> wrote:
> > Your Idlepc values need to be tweaked. It takes some time to find a good
> > one for your pc.
> >
> > Try http://www.gns3.net/ It's much easier to work with.
> >
> > http://www.gns3.net/documentation
> >
> > On Mon, May 11, 2009 at 10:38 AM, Ravi Singh <way2ccie_at_googlemail.com
> >wrote:
> >
> >> Hi Marish,
> >>
> >> 1) As Welly said, the already configured idlepc values in your
> >> topology will not work. You need to find one that suits your system .
> >>
> >> 2) When you find out an idlepc value check how much is your cpu usage
> >> when you have only a couple of routers started. If it is still high
> >> ,say above 40 - 50% , you do not have the optimum idlepc value set up.
> >> You will have to play around a bit to find the best idlepc value.
> >>
> >> 3) do not start all the routers together. Start 2 or 3 , telnet into
> >> them , then then next 2 or 3 and then telnet. Your cpu utilization
> >> increases when the routers are getting started and it decreases when
> >> you telnet and get to the router> prompt.
> >>
> >> And yes,I think a loop in your topology will increase your cpu
> utilization
> >> .
> >>
> >> P.S - do read the dynamips/dynagen tutorial . It does help a lot
> >>
> >> HTH,
> >> Ravi
> >>
> >> On Mon, May 11, 2009 at 2:56 PM, marish shah <contactmarish_at_gmail.com>
> >> wrote:
> >> > Hi Experts,
> >> > I'm facing some problem with my dynamips.(Slowness
> >> > problem).During Using dynamips my CPU Usage always remain 100% and
> make
> >> my
> >> > work very slow.I have CPU with this Specifcations.
> >> > Ram = 6 GB
> >> > Procssor = 2.6 Quote to Core.
> >> > Window = XP
> >> >
> >> > and on this PC I don't have any software install no Anti Virus.
> >> > I'm using IEW dynamips topolgy which already configured with idle pc
> >> value
> >> > So my Q is still I need to put any thing to reduse my CPU utlization.
> >> > And one Q more that when where there is loop in my topology it will
> make
> >> my
> >> > dyamips slow also ?
> >> >
> >> > Thanks.
> >> >
> >> >
> >> > Blogs and organic groups at http://www.ccie.net
> >> >
> >> >
> _______________________________________________________________________
> >> > Subscription information may be found at:
> >> > http://www.groupstudy.com/list/CCIELab.html
> >>
> >>
> >> Blogs and organic groups at http://www.ccie.net
> >>
> >> _______________________________________________________________________
> >> Subscription information may be found at:
> >> http://www.groupstudy.com/list/CCIELab.html
> >>
> >>
> >>
> >>
> >>
> >>
> >>
> >>
> >
> >
> > --
> > Regards,
> > Peter Kurdziel
> >
> >
> > Blogs and organic groups at http://www.ccie.net
> >
> > _______________________________________________________________________
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html

Blogs and organic groups at http://www.ccie.net
Received on Mon May 11 2009 - 19:39:42 ART