Re: Dynamips Issue

whts "Quote to Core." ??

u mean Quad Core? or Core 2 Duo?
Thanking You

Yours Sincerely

Divin Mathew John
divinjohn_at_gmail.com
divin_at_dide3d.com
http://www.dide3d.com
+91 9945430983
+91 9846697191
+974 5008916
PGP PUBLIC KEY BLOCK @ http://www.dide3d.com/divin_Public_PGP_key.txt
Sent from Bangalore, KA, India

On Mon, May 11, 2009 at 8:33 PM, Peter Kurdziel <usaccie_at_gmail.com> wrote:
> Your Idlepc values need to be tweaked. It takes some time to find a good
> one for your pc.
>
> Try http://www.gns3.net/ It's much easier to work with.
>
> http://www.gns3.net/documentation
>
> On Mon, May 11, 2009 at 10:38 AM, Ravi Singh <way2ccie_at_googlemail.com>wrote:
>
>> Hi Marish,
>>
>> 1) As Welly said, the already configured idlepc values in your
>> topology will not work. You need to find one that suits your system .
>>
>> 2) When you find out an idlepc value check how much is your cpu usage
>> when you have only a couple of routers started. If it is still high
>> ,say above 40 - 50% , you do not have the optimum idlepc value set up.
>> You will have to play around a bit to find the best idlepc value.
>>
>> 3) do not start all the routers together. Start 2 or 3 , telnet into
>> them , then then next 2 or 3 and then telnet. Your cpu utilization
>> increases when the routers are getting started and it decreases when
>> you telnet and get to the router> prompt.
>>
>> And yes,I think a loop in your topology will increase your cpu utilization
>> .
>>
>> P.S - do read the dynamips/dynagen tutorial . It does help a lot
>>
>> HTH,
>> Ravi
>>
>> On Mon, May 11, 2009 at 2:56 PM, marish shah <contactmarish_at_gmail.com>
>> wrote:
>> > Hi Experts,
>> > I'm facing some problem with my dynamips.(Slowness
>> > problem).During Using dynamips my CPU Usage always remain 100% and make
>> my
>> > work very slow.I have CPU with this Specifcations.
>> > Ram = 6 GB
>> > Procssor = 2.6 Quote to Core.
>> > Window = XP
>> >
>> > and on this PC I don't have any software install no Anti Virus.
>> > I'm using IEW dynamips topolgy which already configured with idle pc
>> value
>> > So my Q is still I need to put any thing to reduse my CPU utlization.
>> > And one Q more that when where there is loop in my topology it will make
>> my
>> > dyamips slow also ?
>> >
>> > Thanks.
>> >
>> >
>> > Blogs and organic groups at http://www.ccie.net
>> >
>> > _______________________________________________________________________
>> > Subscription information may be found at:
>> > http://www.groupstudy.com/list/CCIELab.html
>>
>>
>> Blogs and organic groups at http://www.ccie.net
>>
>> _______________________________________________________________________
>> Subscription information may be found at:
>> http://www.groupstudy.com/list/CCIELab.html
>>
>>
>>
>>
>>
>>
>>
>>
>
>
> --
> Regards,
> Peter Kurdziel
>
>
> Blogs and organic groups at http://www.ccie.net
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html

Blogs and organic groups at http://www.ccie.net
Received on Mon May 11 2009 - 22:01:15 ART