From: Dayaa Al Zoubi (cciecool@gmail.com)
Date: Wed Mar 11 2009 - 11:12:30 ARST
Sorry i am not that far , still in first lab but i have a problem with the
tunnel in lab 1 it is not coming up , any of you faced this problem or could
be my configuration wrong
thanks
dayaa
ccie 21450
On Wed, Mar 11, 2009 at 5:05 PM, john jacob <john.jj.jacob@googlemail.com>wrote:
> Actually local pool is an option instead of DHCP but unfortunately we
> end up in other issues with Local pool.
> The issue with local pool is the the ip address learnt via Local Pool
> (IPCP) default to a /32 subnet .
> This will have problems with OSPF neighbor realtionship.
>
> However Faris has a solution for the DHCP issue , by specifying the
> Client Identifier in the DHCP scope and it works fine
>
> Cheers
> John
>
> On Wed, Mar 11, 2009 at 3:45 PM, Rich Collins <nilsi2002@gmail.com> wrote:
> > I spent a bit of time with this but could only get a satisfactory
> > result using local pools. Would that be a possibility instead of
> > dhcp?
> >
> > -Rich
> >
> > On Mon, Mar 9, 2009 at 5:40 PM, john jacob <john.jj.jacob@googlemail.com>
> wrote:
> >> Hi ,
> >>
> >> Just a bit stuck with PPPoE with IE Lab 6 of SP workbook.
> >> When i specify the ip address in the DHCP pool via the Host command ,
> >> the client router ( R3 ) doesn not take the ip .
> >> However if I specify a Pool via the network Command under the DHCP
> >> Pool , the client router takes the a randon ip from the pool.
> >>
> >> Cant figure out what i am missing . The configs are as below.
> >>
> >> R5 -- E0/0
> >> ------------------------------------------------- E0/1 -- R3
> >>
> >> R5 is the Server and R3 is the client
> >>
> _-------------------------------------------------------------------------------------------------------------------------------------------------------
> >> R5 - Server configs
> >>
> >> ip dhcp pool R3
> >> network 20.1.35.0 255.255.255.0 ( Client gets and IP
> >> 20.1.35.1/24 with this command)
> >> host 20.1.35.3 255.255.255.0 ( client does not
> >> get any IP with this command ) We need Client to get this IP from R5
> >>
> >> vpdn group 1
> >> accept-dialin
> >> protocol pppoe
> >> virtual-template 1
> >>
> >> interface virtual-template 1
> >> ip add 20.1.35.5 255.255.255.0
> >> peer default ip address dhcp-pool R3
> >>
> >> int e0/0
> >> no ip add
> >> pppoe enable
> >>
> >>
> ------------------------------------------------------------------------------------------------------------------------------------------------------------
> >>
> >> R3 - Client config
> >>
> >> vpdn enable
> >> vpdn-group 1
> >> request- dialin
> >> protocol pppoe
> >>
> >> interface dialer1
> >> ip address dhcp
> >> encapsulation ppp
> >> dialer pool 1
> >> dialer persistant
> >>
> >> int e0/1
> >> pppoe enable
> >> pppoe-client dial-pool-number 1
> >>
> >>
> ____________________________________________________________________________________________
> >>
> >>
> >>
> >> Hope some has already gone through this ,
> >>
> >> Cheers
> >> John .
> >>
> >>
> >> Blogs and organic groups at http://www.ccie.net
> >>
> >> _______________________________________________________________________
> >> Subscription information may be found at:
> >> http://www.groupstudy.com/list/CCIELab.html
> >>
> >>
> >>
> >>
> >>
> >>
> >>
> >>
> >
>
>
>
> --
> ______________________________
> John Jacob
> CCIE # 19213
> Core IP Networks
> Nokia Siemens Networks
> Dubai, U.A.E
> Mob: +971 50 4589370
> ______________________________
>
>
> Blogs and organic groups at http://www.ccie.net
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
Blogs and organic groups at http://www.ccie.net
This archive was generated by hypermail 2.1.4 : Mon Apr 06 2009 - 06:44:04 ART