From: backbone systems (backbone.systems@gmail.com)
Date: Sat Mar 07 2009 - 13:31:01 ARST
sorry boss....can u please send the .NET file tooo.
thanks
On Sat, Mar 7, 2009 at 6:26 PM, Nitin Venugopal <nitinsworld@gmail.com> wrote:
> Pls find the same as below
>
> R1
>
> interface ATM2/0
> no ip address
> no ip directed-broadcast
> no atm enable-ilmi-trap
> no atm ilmi-keepalive
> no clns route-cache
> !
> interface ATM2/0.1 tag-switching
> ip address 172.16.1.5 255.255.255.252
> no ip directed-broadcast
> no atm enable-ilmi-trap
> snmp trap link-status
> mpls label protocol ldp
> tag-switching atm control-vc 31 31
> tag-switching ip
> R2
> interface ATM3/0
> no ip address
> no atm ilmi-keepalive
> mpls label protocol both
> tag-switching atm control-vc 21 22
> tag-switching ip
> no clns route-cache
> !
> interface ATM3/0.1 tag-switching
> ip address 172.16.1.6 255.255.255.252
> tag-switching atm control-vc 21 22
> tag-switching ip
>
> HTH,
>
> Regds
> Nitin
> On Sat, Mar 7, 2009 at 7:15 PM, backbone systems
> <backbone.systems@gmail.com> wrote:
>>
>> Dear Nitin,
>>
>> Can u please send me a sample config with ATM supporting tag-switvching?
>>
>> BB
>>
>> On Sat, Mar 7, 2009 at 5:40 PM, Nitin Venugopal <nitinsworld@gmail.com>
>> wrote:
>> > Yes it is , build your topolgy on dynamips with the below H/W and S/W
>> > Image
>> >
>> > 7200 VXR (NPE 400)
>> > 12.0 (32) S11
>> >
>> > ATM OC3 (MM) port adapter
>> >
>> >
>> >
>> > Regds
>> > Nitin
>> >
>> > On Sat, Mar 7, 2009 at 6:14 PM, backbone systems
>> > <backbone.systems@gmail.com> wrote:
>> >>
>> >> Can anyone please confirm if the following is possible on dynamips,
>> >>
>> >> interface ATM3/0.1 tag-switching
>> >> ip address 150.1.19.1
>> >> tag-switching atm control-vc 40 40
>> >> tag-switching ip
>> >>
>> >>
>> >> interface ATM3/0.1 tag-switching
>> >> ip address 150.1.19.2
>> >> tag-switching atm control-vc 40 40
>> >> tag-switching ip
>> >>
>> >> As far as i know cell made switching is not supported on dynamips?????
>> >> i can not run this command
>> >>
>> >> interface ATM3/0.1 tag-switching
>> >>
>> >> Please confirm???
>> >>
>> >> I was using those interfaces as normal and running mpls ip on the atm
>> >> interface which is frame mode ??? am i right.
>> >>
>> >> On Sat, Mar 7, 2009 at 2:19 PM, Nitin Venugopal <nitinsworld@gmail.com>
>> >> wrote:
>> >> > Hi,
>> >> >
>> >> > You have to define in the subinterface for cell-mode , if it will be
>> >> > a
>> >> > point to point , multipoint , mpls or tag-switching
>> >> >
>> >> > Below will be if its for MPLS
>> >> >
>> >> > interface ATM3/0.1 tag-switching
>> >> > ip address 150.1.19.1
>> >> > tag-switching atm control-vc 40 40
>> >> > tag-switching ip
>> >> >
>> >> >
>> >> > interface ATM3/0.1 tag-switching
>> >> > ip address 150.1.19.2
>> >> > tag-switching atm control-vc 40 40
>> >> > tag-switching ip
>> >> >
>> >> >
>> >> > Regds
>> >> > Nitin
>> >> >
>> >> > On Sat, Mar 7, 2009 at 12:07 PM, Vignesh Sethuraman
>> >> > <sethuvignesh@gmail.com>wrote:
>> >> >
>> >> >> Hello,
>> >> >>
>> >> >> I was configuring basic atm configuration between 2 routers
>> >> >> connected
>> >> >> via
>> >> >> ATM switch in my 4 GB Ram laptop running WindowsXP.
>> >> >>
>> >> >> R1(3/0) ------ 1/0 (ATM SW) 2/0 ------(3/0) R2
>> >> >>
>> >> >> I am unable to ping R1 to R2
>> >> >>
>> >> >> R1:
>> >> >> interface ATM3/0
>> >> >> ip address 150.1.19.1 255.255.255.0
>> >> >> no atm enable-ilmi-trap
>> >> >> no clns route-cache
>> >> >> pvc 0/102
>> >> >> protocol ip 150.1.19.2 broadcast
>> >> >>
>> >> >> R2:
>> >> >> interface ATM3/0
>> >> >> ip address 150.1.19.2 255.255.255.0
>> >> >> no atm enable-ilmi-trap
>> >> >> no clns route-cache
>> >> >> pvc 0/102
>> >> >> protocol ip 150.1.19.1 broadcast
>> >> >>
>> >> >> R1#p 150.1.19.2
>> >> >> Type escape sequence to abort.
>> >> >> Sending 5, 100-byte ICMP Echos to 150.1.19.2, timeout is 2 seconds:
>> >> >> .....
>> >> >> Success rate is 0 percent (0/5)
>> >> >> R1#
>> >> >> I have started my Cell mode atm switch. But i did not do any
>> >> >> mappings
>> >> >> on
>> >> >> the
>> >> >> ATM switch. Do we need to configure mappings on the ATM switch as
>> >> >> like
>> >> >> the
>> >> >> FRSW. I am using InternetworkExpert .net file.
>> >> >>
>> >> >> And also CPU process is showing 100% even if i choose the best
>> >> >> idlepc
>> >> >> shown
>> >> >> in the GNS.
>> >> >>
>> >> >> Could you pleas help me to resolve this issue.
>> >> >>
>> >> >> Thanks,
>> >> >> Vignesh
>> >> >>
>> >> >>
>> >> >> Blogs and organic groups at http://www.ccie.net
>> >> >>
>> >> >>
>> >> >> _______________________________________________________________________
>> >> >> Subscription information may be found at:
>> >> >> http://www.groupstudy.com/list/CCIELab.html
>> >> >
>> >> >
>> >> > Blogs and organic groups at http://www.ccie.net
>> >> >
>> >> >
>> >> > _______________________________________________________________________
>> >> > Subscription information may be found at:
>> >> > http://www.groupstudy.com/list/CCIELab.html
Blogs and organic groups at http://www.ccie.net
This archive was generated by hypermail 2.1.4 : Mon Apr 06 2009 - 06:44:04 ART