Re: CCIE SP Basic Configuration - InternetworkExpert .net file

From: Nitin Venugopal (nitinsworld@gmail.com)
Date: Sat Mar 07 2009 - 13:26:27 ARST

Pls find the same as below

R1

interface ATM2/0
 no ip address
 no ip directed-broadcast
 no atm enable-ilmi-trap
 no atm ilmi-keepalive
 no clns route-cache
!
interface ATM2/0.1 tag-switching
 ip address 172.16.1.5 255.255.255.252
 no ip directed-broadcast
 no atm enable-ilmi-trap
 snmp trap link-status
 mpls label protocol ldp
 tag-switching atm control-vc 31 31
 tag-switching ip
R2

interface ATM3/0
 no ip address
 no atm ilmi-keepalive
 mpls label protocol both
 tag-switching atm control-vc 21 22
 tag-switching ip
 no clns route-cache
!
interface ATM3/0.1 tag-switching
 ip address 172.16.1.6 255.255.255.252
 tag-switching atm control-vc 21 22
 tag-switching ip

HTH,

Regds
Nitin
On Sat, Mar 7, 2009 at 7:15 PM, backbone systems <backbone.systems@gmail.com
> wrote:

> Dear Nitin,
>
> Can u please send me a sample config with ATM supporting tag-switvching?
>
> BB
>
> On Sat, Mar 7, 2009 at 5:40 PM, Nitin Venugopal <nitinsworld@gmail.com>
> wrote:
> > Yes it is , build your topolgy on dynamips with the below H/W and S/W
> Image
> >
> > 7200 VXR (NPE 400)
> > 12.0 (32) S11
> >
> > ATM OC3 (MM) port adapter
> >
> >
> >
> > Regds
> > Nitin
> >
> > On Sat, Mar 7, 2009 at 6:14 PM, backbone systems
> > <backbone.systems@gmail.com> wrote:
> >>
> >> Can anyone please confirm if the following is possible on dynamips,
> >>
> >> interface ATM3/0.1 tag-switching
> >> ip address 150.1.19.1
> >> tag-switching atm control-vc 40 40
> >> tag-switching ip
> >>
> >>
> >> interface ATM3/0.1 tag-switching
> >> ip address 150.1.19.2
> >> tag-switching atm control-vc 40 40
> >> tag-switching ip
> >>
> >> As far as i know cell made switching is not supported on dynamips?????
> >> i can not run this command
> >>
> >> interface ATM3/0.1 tag-switching
> >>
> >> Please confirm???
> >>
> >> I was using those interfaces as normal and running mpls ip on the atm
> >> interface which is frame mode ??? am i right.
> >>
> >> On Sat, Mar 7, 2009 at 2:19 PM, Nitin Venugopal <nitinsworld@gmail.com>
> >> wrote:
> >> > Hi,
> >> >
> >> > You have to define in the subinterface for cell-mode , if it will be
> a
> >> > point to point , multipoint , mpls or tag-switching
> >> >
> >> > Below will be if its for MPLS
> >> >
> >> > interface ATM3/0.1 tag-switching
> >> > ip address 150.1.19.1
> >> > tag-switching atm control-vc 40 40
> >> > tag-switching ip
> >> >
> >> >
> >> > interface ATM3/0.1 tag-switching
> >> > ip address 150.1.19.2
> >> > tag-switching atm control-vc 40 40
> >> > tag-switching ip
> >> >
> >> >
> >> > Regds
> >> > Nitin
> >> >
> >> > On Sat, Mar 7, 2009 at 12:07 PM, Vignesh Sethuraman
> >> > <sethuvignesh@gmail.com>wrote:
> >> >
> >> >> Hello,
> >> >>
> >> >> I was configuring basic atm configuration between 2 routers connected
> >> >> via
> >> >> ATM switch in my 4 GB Ram laptop running WindowsXP.
> >> >>
> >> >> R1(3/0) ------ 1/0 (ATM SW) 2/0 ------(3/0) R2
> >> >>
> >> >> I am unable to ping R1 to R2
> >> >>
> >> >> R1:
> >> >> interface ATM3/0
> >> >> ip address 150.1.19.1 255.255.255.0
> >> >> no atm enable-ilmi-trap
> >> >> no clns route-cache
> >> >> pvc 0/102
> >> >> protocol ip 150.1.19.2 broadcast
> >> >>
> >> >> R2:
> >> >> interface ATM3/0
> >> >> ip address 150.1.19.2 255.255.255.0
> >> >> no atm enable-ilmi-trap
> >> >> no clns route-cache
> >> >> pvc 0/102
> >> >> protocol ip 150.1.19.1 broadcast
> >> >>
> >> >> R1#p 150.1.19.2
> >> >> Type escape sequence to abort.
> >> >> Sending 5, 100-byte ICMP Echos to 150.1.19.2, timeout is 2 seconds:
> >> >> .....
> >> >> Success rate is 0 percent (0/5)
> >> >> R1#
> >> >> I have started my Cell mode atm switch. But i did not do any mappings
> >> >> on
> >> >> the
> >> >> ATM switch. Do we need to configure mappings on the ATM switch as
> like
> >> >> the
> >> >> FRSW. I am using InternetworkExpert .net file.
> >> >>
> >> >> And also CPU process is showing 100% even if i choose the best idlepc
> >> >> shown
> >> >> in the GNS.
> >> >>
> >> >> Could you pleas help me to resolve this issue.
> >> >>
> >> >> Thanks,
> >> >> Vignesh
> >> >>
> >> >>
> >> >> Blogs and organic groups at http://www.ccie.net
> >> >>
> >> >>
> _______________________________________________________________________
> >> >> Subscription information may be found at:
> >> >> http://www.groupstudy.com/list/CCIELab.html
> >> >
> >> >
> >> > Blogs and organic groups at http://www.ccie.net
> >> >
> >> >
> _______________________________________________________________________
> >> > Subscription information may be found at:
> >> > http://www.groupstudy.com/list/CCIELab.html

Blogs and organic groups at http://www.ccie.net

This archive was generated by hypermail 2.1.4 : Mon Apr 06 2009 - 06:44:04 ART