From: backbone systems (backbone.systems@gmail.com)
Date: Sat Mar 07 2009 - 13:15:07 ARST
Dear Nitin,
Can u please send me a sample config with ATM supporting tag-switvching?
BB
On Sat, Mar 7, 2009 at 5:40 PM, Nitin Venugopal <nitinsworld@gmail.com> wrote:
> Yes it is , build your topolgy on dynamips with the below H/W and S/W Image
>
> 7200 VXR (NPE 400)
> 12.0 (32) S11
>
> ATM OC3 (MM) port adapter
>
>
>
> Regds
> Nitin
>
> On Sat, Mar 7, 2009 at 6:14 PM, backbone systems
> <backbone.systems@gmail.com> wrote:
>>
>> Can anyone please confirm if the following is possible on dynamips,
>>
>> interface ATM3/0.1 tag-switching
>> ip address 150.1.19.1
>> tag-switching atm control-vc 40 40
>> tag-switching ip
>>
>>
>> interface ATM3/0.1 tag-switching
>> ip address 150.1.19.2
>> tag-switching atm control-vc 40 40
>> tag-switching ip
>>
>> As far as i know cell made switching is not supported on dynamips?????
>> i can not run this command
>>
>> interface ATM3/0.1 tag-switching
>>
>> Please confirm???
>>
>> I was using those interfaces as normal and running mpls ip on the atm
>> interface which is frame mode ??? am i right.
>>
>> On Sat, Mar 7, 2009 at 2:19 PM, Nitin Venugopal <nitinsworld@gmail.com>
>> wrote:
>> > Hi,
>> >
>> > You have to define in the subinterface for cell-mode , if it will be a
>> > point to point , multipoint , mpls or tag-switching
>> >
>> > Below will be if its for MPLS
>> >
>> > interface ATM3/0.1 tag-switching
>> > ip address 150.1.19.1
>> > tag-switching atm control-vc 40 40
>> > tag-switching ip
>> >
>> >
>> > interface ATM3/0.1 tag-switching
>> > ip address 150.1.19.2
>> > tag-switching atm control-vc 40 40
>> > tag-switching ip
>> >
>> >
>> > Regds
>> > Nitin
>> >
>> > On Sat, Mar 7, 2009 at 12:07 PM, Vignesh Sethuraman
>> > <sethuvignesh@gmail.com>wrote:
>> >
>> >> Hello,
>> >>
>> >> I was configuring basic atm configuration between 2 routers connected
>> >> via
>> >> ATM switch in my 4 GB Ram laptop running WindowsXP.
>> >>
>> >> R1(3/0) ------ 1/0 (ATM SW) 2/0 ------(3/0) R2
>> >>
>> >> I am unable to ping R1 to R2
>> >>
>> >> R1:
>> >> interface ATM3/0
>> >> ip address 150.1.19.1 255.255.255.0
>> >> no atm enable-ilmi-trap
>> >> no clns route-cache
>> >> pvc 0/102
>> >> protocol ip 150.1.19.2 broadcast
>> >>
>> >> R2:
>> >> interface ATM3/0
>> >> ip address 150.1.19.2 255.255.255.0
>> >> no atm enable-ilmi-trap
>> >> no clns route-cache
>> >> pvc 0/102
>> >> protocol ip 150.1.19.1 broadcast
>> >>
>> >> R1#p 150.1.19.2
>> >> Type escape sequence to abort.
>> >> Sending 5, 100-byte ICMP Echos to 150.1.19.2, timeout is 2 seconds:
>> >> .....
>> >> Success rate is 0 percent (0/5)
>> >> R1#
>> >> I have started my Cell mode atm switch. But i did not do any mappings
>> >> on
>> >> the
>> >> ATM switch. Do we need to configure mappings on the ATM switch as like
>> >> the
>> >> FRSW. I am using InternetworkExpert .net file.
>> >>
>> >> And also CPU process is showing 100% even if i choose the best idlepc
>> >> shown
>> >> in the GNS.
>> >>
>> >> Could you pleas help me to resolve this issue.
>> >>
>> >> Thanks,
>> >> Vignesh
>> >>
>> >>
>> >> Blogs and organic groups at http://www.ccie.net
>> >>
>> >> _______________________________________________________________________
>> >> Subscription information may be found at:
>> >> http://www.groupstudy.com/list/CCIELab.html
>> >
>> >
>> > Blogs and organic groups at http://www.ccie.net
>> >
>> > _______________________________________________________________________
>> > Subscription information may be found at:
>> > http://www.groupstudy.com/list/CCIELab.html
Blogs and organic groups at http://www.ccie.net
This archive was generated by hypermail 2.1.4 : Mon Apr 06 2009 - 06:44:04 ART