From: Tyson Scott (tscott@ipexpert.com)
Date: Mon Dec 29 2008 - 22:12:09 ARST
Tony,
I guess all I am saying is configure the port as a layer2 port and
configure the layer3 interface.
Just the same way as the old hybrid 6500 days.
RTR#sh run int f0/3/0
interface FastEthernet0/3/0
switchport trunk native vlan 200
switchport mode trunk
switchport voice vlan 400
end
RTR#sh ip int brief
Interface IP-Address OK? Method Status
Protocol
FastEthernet0/3/0 unassigned YES unset up up
FastEthernet0/3/1 unassigned YES unset up down
FastEthernet0/3/2 unassigned YES unset up down
FastEthernet0/3/3 unassigned YES unset up down
Vlan200 10.10.102.1 YES manual up up
Vlan400 10.10.202.1 YES manual up up
On Mon, Dec 29, 2008 at 7:03 PM, Tony Varriale
<tvarriale@flamboyaninc.com> wrote:
> Not going to happen. They are l2 only.
>
> tv
>
> -----Original Message-----
> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
> Hobbs
> Sent: Monday, December 29, 2008 5:57 PM
> To: Haroon
> Cc: Cisco certification
> Subject: Re: Cisco 2800s and HWICs
>
> If cost is an issue I would check get the hwic-4esw if it allows "no
> switchport". I don't have one to verify. If it's for lab purposes it should
> be fine. An online rack I use has a 2800 with a nm-16esw and it allows the
> no switchport command.
>
> Does anyone here know?
>
> On Mon, Dec 29, 2008 at 4:39 PM, Haroon <itguy.pro@gmail.com> wrote:
>
>> Thanks Hobbs.
>>
>> I was just looking at those documents.
>>
>> It seems HWIC-1FE would be a better option but are bit expensive though,
>> is anybody selling HWIC-1FE, I need 4 or 5 pieces?
>>
>> Thanks,
>>
>> Haroon
>>
>>
>> On Mon, Dec 29, 2008 at 6:34 PM, Hobbs <deadheadblues@gmail.com> wrote:
>>
>>> Hi,
>>>
>>>
>>>
> http://www.cisco.com/en/US/products/ps5854/products_relevant_interfaces_and_
> modules.html
>>>
>>>
>>>
> http://www.cisco.com/en/US/prod/collateral/routers/ps5854/product_data_sheet
> 0900aecd80581fe6_ps5853_Products_Data_Sheet.html
>>>
>>> I believe the switch module interfaces can be converted to routed ports
>>> with the "no switchport" command. Don't know if all the switch modules
>>> support it though. Otherwise take a look at the links above for HWIC-1FE.
>>>
>>> hth
>>>
>>> On Mon, Dec 29, 2008 at 3:51 PM, Haroon <itguy.pro@gmail.com> wrote:
>>>
>>>> Hello Experts,
>>>>
>>>> I have couple of 2811s and few 2821s. I need to add 2 additional
>>>> Fast-Ethernet interfaces on each of these routers, what is the best way
>>>> to
>>>> go about doing that? Which module (part#?) would allow layer3
> capability?
>>>>
>>>> I understand HWIC-4ESW would but isn't that a switch which doesn't
> really
>>>> do
>>>> routing on it self but forwards it to the host?
>>>>
>>>> Please help.
>>>>
>>>> Thanks,
>>>>
>>>> Haroon
>>>>
>>>>
>>>> Blogs and organic groups at http://www.ccie.net
>>>>
>>>> _______________________________________________________________________
>>>> Subscription information may be found at:
>>>> http://www.groupstudy.com/list/CCIELab.html
>
>
> Blogs and organic groups at http://www.ccie.net
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
>
> Blogs and organic groups at http://www.ccie.net
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
>
>
>
>
>
>
>
-- Tyson Scott - CCIE #13513 R&S and Security Technical Instructor - IPexpert, Inc.Telephone: +1.810.326.1444 Fax: +1.810.454.0130 Mailto: tscott@ipexpert.com
Join our free online support and peer group communities: http://www.IPexpert.com/communities
IPexpert - The Global Leader in Self-Study, Classroom-Based, Video On Demand and Audio Certification Training Tools for the Cisco CCIE R&S Lab, CCIE Security Lab, CCIE Service Provider Lab , CCIE Voice Lab and CCIE Storage Lab Certifications.
Blogs and organic groups at http://www.ccie.net
This archive was generated by hypermail 2.1.4 : Thu Jan 01 2009 - 12:53:10 ARST