From: Geert Nijs (Geert.Nijs@simac.be)
Date: Wed May 28 2008 - 07:27:47 ART
Hi Ananth,
I will keep that in mind, but as you said, my problem does not arrive when connecting a 25th phone. It just does not work on any port, not for a single phone,
because the switch advertises that it has no power available, although it is powered :-)
sh power inline
Module Available Used Remaining
(Watts) (Watts) (Watts)
------ --------- -------- ---------
1 370.0 170.1 199.9
2 370.0 155.6 214.4
3 370.0 187.1 182.9
4 n/a n/a n/a <<<<<<<-------- ??????????????
We will propably replace the switch.
mvg,
Geert
________________________________
From: A.G. Ananth Sarma (GMail) [ananth.sarma@gmail.com]
Sent: 28 May 2008 11:35
To: Geert Nijs
Cc: ccielab@groupstudy.com
Subject: Re: 3750 and power inlnie
Hi Geert,
I had a similar issue on 3560 PoE switches where the 25th phone does not get the power.
This is due to the fact that the power available on the switch was 370 W and by default, each port is allocated 15.4 W.
(370 / 15.4 = 24.026 phones max).
As per one of the Voice Experts in the GS, I tweaked the power on the switch ports to 6.3W ( IP Phone 7941) and 5.0 W ( IP Phone 7911) and so on. By this way, I managed to utilise more or less all the ports.
( IP Phone 7971 should also work with 6.3 W which I do not remember exactly).
To do this, go to the interface config mode and run : power inline consumption 6300
You may get a warning, but that is ok to ignore. Better shutdown the port before apply this command.
I know what I have written above may not be fully relevant to your case, but may be handy for later usage.
Try shutting down the ports and enable / Or reload the 4th switch during non-production hours.
Let us know as to how you fix this.
Regards,
Ananth
On Wed, May 28, 2008 at 11:43 AM, Geert Nijs <Geert.Nijs@simac.be<mailto:Geert.Nijs@simac.be>> wrote:
Hi group,
Is it possible for a 3750 to fail completely regarding PoE, but keep functioning normally for the rest ?
Are all PoE-functions controlled by one critical "power controller" maybe ?
I have a PoE-capable switch, where suddenly the available power has dropped to 0 and not a single port gets powered....
sh power inline
Module Available Used Remaining
(Watts) (Watts) (Watts)
------ --------- -------- ---------
1 370.0 170.1 199.9
2 370.0 155.6 214.4
3 370.0 187.1 182.9
4 n/a n/a n/a <<<<<<<-------- ??????????????
Switch Ports Model SW Version SW Image
------ ----- ----- ---------- ----------
* 1 52 WS-C3750-48P 12.2(25)SED1 C3750-IPBASE-M
2 52 WS-C3750-48P 12.2(25)SED1 C3750-IPBASE-M
3 52 WS-C3750-48P 12.2(25)SED1 C3750-IPBASE-M
4 52 WS-C3750-48P 12.2(25)SED1 C3750-IPBASE-M <<<--- power enabled.
regards,
Geert
________________________________
disclaimer : http://webservices.simac.be/disclaimer.htm
This archive was generated by hypermail 2.1.4 : Mon Jun 02 2008 - 06:59:18 ART