From: Dan C (cdan2154@gmail.com)
Date: Sun May 11 2008 - 03:40:57 ART
Hi Dave,
You can always cascade the virtual links by doing so, every time you use a
VL you are extending the Area 0 by one hop ( router ) if you use any
authentication you must add Area 0 to the hop router, keeping in mind that
you can not create a Virtual link over stub areas.
Cheers,
Dan
On Sun, May 11, 2008 at 1:10 AM, dave dave <funccie@gmail.com> wrote:
> I am not on my laptop, so can someone lab it or if any one tested it first
> can please confirm that VL will work as mentioned in reply.
>
> Regards,
> Dave
>
> Regards
> Dave
>
>
> On 5/10/08, Jason Madsen <madsen.jason@gmail.com> wrote:
> >
> > Dave,
> >
> > seems as though you could use virtual links between R4&R5, R3&R4, R2&R3,
> > and R1&R2...I agree, doesn't look as though you'd need one between R6&R7
> > since R6 is already touching area 0.
> >
> > as far as the virtual links go, I've never seen multiple virtual links
> back
> > to back. it's just a suggestion to try. the univercd doesn't make
> mention
> > of using virtual links in tandem like this. i guess if that doesn't
> work,
> > you might have to go the gre route, although i suspect using these
> virtual
> > links in tandem will work snice since each virtual link becomes an
> extension
> > of area 0.
> >
> > good luck. let know how it turns out...this is pretty neat.
> >
> > Jason
> >
> >
> > On Sat, May 10, 2008 at 2:43 AM, Shine <shinepjoseph@iprimus.com.au>
> > wrote:
> >
> >> I think the answer is Virtual link between R1&R2, R2&R3, R3&R4, R4&R5
> and
> >> R6&R7.
> >>
> >> Regards,
> >> Shine
> >>
> >>
> >> -----Original Message-----
> >> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
> >> dave
> >> dave
> >> Sent: Saturday, 10 May 2008 4:42 PM
> >> To: Cisco certification
> >> Subject: OSPF Question for connecting to Area 0
> >>
> >> Hi Expert,
> >>
> >> I dont have any area as a stub area then how will i connect the all
> area
> >> to area0 & how will able to see the lookback addres in area100 on router
> >> R7.
> >> Can it possible with out using GRE tunnel?
> >>
> >>
> >> * loopback in area 100<==* R1 <--Area10---> R2 <--Area20 --->R3
> >> <---Area30---->R4<---Area40---->R5<-- *Area0 *--->R6 <---Area50---->R7
> >>
> >> Regards,
> >> Mukesh
> >>
> >>
> >> _______________________________________________________________________
> >> Subscription information may be found at:
> >> http://www.groupstudy.com/list/CCIELab.html
> >>
> >>
> >> _______________________________________________________________________
> >> Subscription information may be found at:
> >> http://www.groupstudy.com/list/CCIELab.html
>
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Mon Jun 02 2008 - 06:59:16 ART